• Energy Research
• Closed Access close
• Restricted close
• 6. Clean water close
• 14. Life underwater close
• CA close
• GB close
• DE close

Abstract In this study, crude cellulose derived from cornstalk, after bleaching, was used as raw material for the synthesis of sodium carboxymethyl cellulose (CMC) by reacting with the cellulose with NaOH and chloroacetic acid at 75 °C for 1.5 h. Effects of alkali dosage, concentration of chloroacetic acid on the physical and chemical properties of the CMC products were investigated. It was revealed that the reactants alkali reagent/chloroacetic acid/cellulose at the molar ratio of 4.6:2.8:1and 4:2.5:1, or at the molar ratio of NaOH/ClCH 2 COOH ≈1.6–1.64, resulted in CMC products of relatively high water solubility. The viscosity-average molecular weight M v of these two CMC products obtained at molar ratios of 4.0:2.5:1 and 4.6:2.8:1 is in the range of 1.94 × 10 4 –2.48 × 10 4 g mol −1 , and the average DS of the two products are 0.57 and 0.85, respectively. As the solute concentration is above 2 wt%, the viscosity of the CMC-water solution exhibits nonlinear (exponential) increasing with increasing the solute concentration (typical of non-Newton fluids).

Among various bioreactors examined in anaerobic digestion and dark fermentation, UASB bioreactor has shown to be a promising alternative. However, mass transfer resistance and biomass washout have been the issues that reported as draw backs of the granular system in the literature. Another problem associated with such a system is its long start-up period as a result of biomass washout and long microbial granulation stage. In this paper, the results obtained from an UASFF bioreactor in methane (AD process) and hydrogen (DF process) production from POME, are presented to assess mass transfer of substrate into the granules and also study the role of internal packing used in the middle part of reactor in the process stability. The value of effectiveness factor, η, for AD and DF processes were calculated to be 0.96 and 0.94, respectively, indicating that there was no mass transfer resistance due to internal and/or external factors. The results showed that the packing material could retain biomass in the reactor and had outstanding contribution in the granulation enhancement. Its role as a supplementing treatment stage was more significant at low HRTs and up-flow velocities.

Bioplastics are alternatives of conventional petroleum-based plastics. Bioplastics are polymers processed from renewable sources and are biodegradable. This study aims at conducting an environmental impact assessment of the bioprocessing of agricultural wastes into bioplastics compared to petro-plastics using an LCA approach. Bioplastics were produced from potato peels in laboratory. In a biochemical reaction under heating, starch was extracted from peels and glycerin, vinegar and water were added with a range of different ratios, which resulted in producing different samples of bio-based plastics. Nevertheless, the environmental impact of the bioplastics production process was evaluated and compared to petro-plastics. A life cycle analysis of bioplastics produced in laboratory and petro-plastics was conducted. The results are presented in the form of global warming potential, and other environmental impacts including acidification potential, eutrophication potential, freshwater ecotoxicity potential, human toxicity potential, and ozone layer depletion of producing bioplastics are compared to petro-plastics. The results show that the greenhouse gases (GHG) emissions, through the different experiments to produce bioplastics, range between 0.354 and 0.623 kg CO2 eq. per kg bioplastic compared to 2.37 kg CO2 eq. per kg polypropylene as a petro-plastic. The results also showed that there are no significant potential effects for the bioplastics produced from potato peels on different environmental impacts in comparison with poly-β-hydroxybutyric acid and polypropylene. Thus, the bioplastics produced from agricultural wastes can be manufactured in industrial scale to reduce the dependence on petroleum-based plastics. This in turn will mitigate GHG emissions and reduce the negative environmental impacts on climate change.

The operation of centrifugal pumps can generate instabilities and pressure pulsations that may be detrimental to the integrity and performance of the pump. In the present study a numerical investigation of the time variation of pressure within a complete centrifugal pump was undertaken. A range of parameters and three flow rates were investigated and the pulsations were extracted at 15 different locations covering important pump regions. The transient flow results compared reasonably with experimental data obtained in a limited experimental survey and clearly indicated the pump locations experiencing the largest pulsation levels. It was also noted that monitoring pulsations at the top dead centre of the pump volute casing would provide a better indication of internal pump pulsations than monitoring at the discharge.

Abstract Bitumen recovery by steam-solvent coinjection involves the coupled thermal/compositional mechanisms for reduction of bitumen viscosity. Reliable design of such processes requires reservoir flow simulation based on a proper phase-behavior model so that the oleic-phase viscosity near the steam-chamber edge can be modeled reliably. However, the effect of bitumen characterization (e.g., the number of pseudo components used) on steam-solvent coinjection simulation has not been studied in detail, and can be realized only after running multiple reservoir simulations, which is time consuming. There are two main objectives in this paper. One is to develop a reliable method for bitumen characterization by improving the fluid characterization method that was recently developed based on perturbation from n-alkanes (PnA). The other is to develop a novel analytical method for assessing the sensitivity of a particular coinjection simulation to bitumen characterization without having to perform reservoir simulations. A simulation case study is given to validate this analytical method. A proper number of pseudo components for bitumen characterization cannot be determined without considering the effect of phase behavior on the oleic-phase viscosity at chamber-edge conditions in steam-solvent coinjection simulation. Results show that the analytical method developed in this research can detect the sensitivity of recovery simulation to bitumen characterization without performing multiple flow simulations using different sets of fluid models. The PnA-based method developed for bitumen characterization gives reliable predictions of phase behavior for bitumen/solvent mixtures with a small amount of experimental data.

Abstract This paper investigates the hydrodynamics of a seabed-mounted, bottom-hinged, flap-type wave energy converter in shallow water. A conceptual model of the hydrodynamics of the device has been formulated and shows that, as the motion of the flap is highly constrained, the magnitude of the wave force on the flap is the key determinant of power capture. The results from a physical modelling program have been used in conjunction with numerical data from WAMIT to validate the conceptual model. The work finds that designing the device to increase the wave force is more profitable than designing it to be tuned to the incident wave climate. As wave force is the primary driver of device performance it is shown that the flap should fill the water column and pierce the water surface to reduce decoupling due to wave overtopping. It is concluded that, in order to maximize capture factor at a typical North Atlantic site, the flap should be approximately 20–30 m wide, with large diameter rounded side edges, having its pivot close to the seabed and its top edge piercing the water surface.

SummaryThe German government has adopted a law that requires sewage plants to go beyond the recovery of phosphorus from wastewater and to promote recycling. We argue that there is no physical global short‐ or mid‐term phosphorus scarcity. However, we also argue that there are legitimate reasons for policies such as those of Germany, including: precaution as a way to ensure future generations’ long‐term supply security, promotion of technologies for closed‐loop economics in a promising stage of technology development, and decrease in the current supply risk with a new resource pool.

Use of a pilot-scale fixed-film bioreactor was investigated for remediation of bromate contamination within groundwater. Bromate reduction with stoichiometric production of bromide was observed, providing supporting evidence for complete reduction of bromate with no production of stable intermediates. Reduction of 87-90% bromate from an influent concentration of 1.1 mg L(-1) was observed with retention times of 40-80 h. Lower retention times led to decreases in bromate reduction capability, with 11.5% removal at a 10 h retention time. Nitrate reduction of 76-99% from a 30.7 mg L(-1) as NO(3)(-) influent was observed at retention times of 10-80 h, although an increase in nitrite production to 2.7 mg L(-1) occurred with a 10 h retention time. Backwashing was not required, with the large plastic packing media able to accommodate biomass accumulation without decreases in operational efficiency. This study has provided proof of concept and demonstrated the potential of biological bromate reduction by fixed-film processes for remediation of a bromate contaminated groundwater source.

Abstract The development of predictive mathematical models for water management in polymer electrolyte membrane fuel cells requires detailed understanding of water distribution and water transport across the Nafion layer. The anisotropic microstructure of Nafion suggests the measurement of water content and mass transport should be along the fuel cell functional direction, i.e. across the membrane. Non-invasive, high resolution, microscopy measurements of this type are very challenging. We report here the calibration of a minimal mathematical model for diffusive water transport in Nafion against data from high-resolution water content maps determined with a new magnetic resonance imaging methodology developed for this purpose. A mock fuel cell was designed to permit well-controlled wetting and drying boundary conditions. With no chemical potential driving force involved, we assume the water transport behavior will be dominated by diffusion. Moreover we show that, in this context, our model is mathematically equivalent to the traditional permeation models based upon saturation dependent pressure gradients via a capillary pressure ansatz. The non-linear equilibrium water distribution across the Nafion membrane measured in this work suggests a bi-modal diffusivity. The model constructed associates distinct transport behaviors to water contents above and below a critical threshold, consistent with a rearrangement of a micro-structural pore network. The experimental observation and the model prediction agree with the primary features of Weber's model of Nafion, which predicts distinct modes of transport for hydration fronts traversing the through-plane direction of the membrane.