• Energy Research
• other engineering and technologies close
• GB close
• RU close
• DE close
• UA close

The path congestion and communication risks of electric power communication network have emerged as the carried businesses are becoming more and more heavy. In this paper, a multi-objective optimization method for power communication network routing considering the importance of the carried businesses is proposed to reduce load imbalance and transmission risk. Firstly, information entropy is introduced as the objective of communication network load balancing optimization. And a risk assessment model for power communication network nodes and links is established. Then fuzzy membership functions are adopted to singularize the two objectives to jointly optimize path congestion and communication risks. The device nodes are dynamically divided according to the carried businesses to pursue the global optimization of the power communication network in which the Yen's algorithm is adopted. Finally, this paper uses the IEEE 30-bus communication network to carry out case simulations and analyzes the proposed method to verify the effectiveness and feasibility.

Torrefaction is considered as a method for producing biofuels with improved characteristics compared to those of the “raw” biomass (higher calorific value, moisture resistance, better grindability). The torrefaction process is an endothermic process that is usually carried out in a gaseous atmosphere in the absence of oxygen. To reduce the required heat input, it is proposed to employ the oxidative torrefaction and conduct the process in a fluidized bed agitated with flue gases containing less than 6% oxygen. Preliminary studies of the oxidative torrefaction of sunflower husks, including thermogravimetric analysis of the treated material, have shown that the heat treatment time for the biomass should be at least 5 min. A fluidized bed is a reactor with ideal mixing of the treated material where uniform treatment of raw material particles cannot generally be attained. To overcome this disadvantage of the fluidization technique and achieve the required residence time for biomass in a fluidized bed during a continuous torrefaction process, it was proposed to equip a torrefaction reactor with a series of vertical baffles spaced at 50 mm. These baffles induce a loop-like flow of the processed biomass from the inlet to the outlet of the reactor. To investigate the residence time for husk particles in the reactor, a tracer, which was colored to husk particles' color with a water-soluble dye which did not change the weight and size of the particles, was injected into the bed of uncolored particles. Tracer samples were taken every 30 s at the outlet of the reactor and were analyzed using a special procedure to determine the fraction of colored particles in each sample. This enabled us to gauge the time during which the colored particles injected into the fluidized bed reached the point of their discharge from the bed. Studies performed in a “cold” model of the reactor showed that a series of vertical baffles in the bed can provide the required residence time for biomass in a reactor including commercial reactors. Plates can provide the necessary biomass residence time in the reactor.

Abstract Secondary concentrators are used in solar concentrating systems to redirect solar beams reflected by the primary concentrators to the focal point or line. These components allow to increase the concentrated solar flux density and hence to lower thermal radiation losses. Solar reflectors for secondary concentrators are permanently exposed to environmental conditions, high radiation fluxes and elevated temperatures that potentially cause stress and degradation throughout the time. Therefore, analyzing solar reflectors of secondary concentrators by simulating these conditions is crucial. No previous research works about the durability of solar reflector materials for secondary concentrators have been reported. The present work is focused on studying the degradation of the reflector materials by simulating accelerated aging, caused by several ambient parameters and the effect of concentrated radiation. Both cooled and uncooled systems for secondary concentrators are included in this study. According to results obtained, aluminum reflectors and thin silvered-glass reflectors glued to an aluminum structure showed minimum reflectance losses and structural degradation under the operation conditions of cooled 3D secondary concentrators (tower systems). Following critical aspects to avoid reflector degradation were identified: to select a suitable adhesive material to glue the thin silvered-glass reflector to the support aluminum structure, to properly protect reflectors edges, to design a suitable cooling system and to avoid the combination of high radiation fluxes with mechanical stress. In addition, laminated silvered-glass reflectors have shown to be suitable for uncooled 2D secondary concentrators (Fresnel collectors). Furthermore, a comparison with naturally aged secondary concentrators using silvered-glass reflectors glued to an aluminum structure revealed that the simulated degradation under accelerated conditions performed in this work did reproduce the most frequent degradation patterns suffered in real operating conditions.

This paper introduces a model predictive control (MPC) strategy for the purpose of fuel-optimal operation of a range-extender hybrid vehicle. The modern navigation system nowadays can provide abundant road information. Using this information, the proposed controller solves a global optimization problem offline in order to determine a preset trajectory of the state of charge (SoC). The online MPC uses the resulting SoC trajectory as set-points for the terminal state in every moving horizon. Repeating this process, the optimal energy management along the trip to be traveled can thus be calculated. This proposed control strategy is implemented in the commercial vehicle simulation environment IPG CarMaker. From the first simulation results, the proposed strategy shows a promising fuel saving potential with real-time capability.

AbstractIn this paper a complete vehicle system simulation tool chain which applies a Multi Objective Optimization (MOO) methodology for designing the Electric Powertrain (ePT) of Battery Electric Vehicles (BEV) is presented. Optimization scope includes all relevant electric powertrain components from battery, inverter, electric machine to gear box. In addition to cost, vehicle dynamics, energy consumption and range are further optimization targets. For an overall minimal system cost design a multiplicity of interactions between all powertrain components has to be taken into account. High system complexity prevents an expert to consider all relevant correlations without the support of numeric simulation tools. The presented simulation tool chain enables fast identification of the best cost/benefit trade off regarding system cost while considering all defined system performance requirements. The approach enables experts to find unconventional solutions which would have been overlooked applying a classical straight forward approach and, thus, helps to sharpen the expert's knowledge in cause-effect relationships on the system level. Typical use cases are given and illustrated by several practical examples.

Abstract Transient thermal behaviors of ultra-supercritical steam turbine control valves during the cold start warm-up process of steam turbine systems were comprehensively studied using conjugate heat transfer (CHT) simulation. The geometrical configurations and boundary conditions used in simulation were identical to the field setup in a thermal power plant. The simulated temperature variations were first validated using measurements by the flush-mounted thermocouples inside the solid valve bodies. The CHT simulation implementing the shear stress transport (SST) turbulence model demonstrated good agreement with the field data, and the overall numerical errors were below 10%; however, the numerical errors of the simulation, which used empirical heat transfer coefficients at the fluid–solid interfaces, reached 40%. The determined temperature differences between the cold valve bodies with the hot steam flow decreased significantly. Specifically, the temperature differences along the inner wall surfaces of the valve bodies decreased to less than 50 °C. Further investigation of the transient heat flux distributions and Nusselt number distributions confirmed that the unsteady flow behaviors, such as the alternating oscillations of the annular wall-attached jet, the central reverse flow and the intermediate shear layer instabilities, enhanced the fluid–solid heat convection process and thus contributed to the warming up of the solid valve bodies.

This paper reports the generalized results of computer simulation of physical processes at a rotor-disk film evaporating plant. Optimization of the operation mode cannot be achieved without establishing patterns in the course of physical processes. We have proposed a computer model of hydrodynamics that accounts for all the features, initial and boundary conditions. The results of computer simulations make it possible to adequately assess the effectiveness of using a rotor-disk film evaporating plant (RDFVP) for the concentration of heat-labile materials. We have established patterns in the course of physical processes within a structure of RDFVP by using computer simulation of hydrodynamics in the programming environment ANSYS and applying a k-e turbulence model. The result of simulation is the derived velocity fields of the concentrated fluid (w max =0.413 m/s) and the gas phase (w max =8.176 m/s), as well as the magnitude of values for shear stress τ=0.94·10 -6 Pa. It was established that the gas heat-carrier is characterized by the highly-turbulent flows with maximum values for kinetic energy TKE max =8.985·10 -1 m 2 /s 2 . The reliability of results is ensured by the correctness, completeness, and adequacy of physical assumptions when stating the problem and while solving it using the computer aided design system ANSYS. It has been established that the proposed structure is an effective alternative to equipment for the concentration of solutions. The data obtained could be used when designing heat-and-mass-exchange equipment for the highly efficient dehydration of thermolabile materials

The passivation of iron and steel (DIN 1623) was studied by integral and depth selective conversion electron Mossbauer spectroscopy and Auger electron spectroscopy. Thickness and phase composition of the passive layer formed in sulphate solution and in a phosphate buffer were determined in dependence on the anodic potential and the duration of the passivating procedure. The experimental results lead to the conclusion that not the whole oxidic layer is responsible for the passivity but only a very thin intermediate layer formed between the cubic substrate and the rhombic oxide (γ-FeOOH) cover.

AbstractShipbuilding is an energy-intensive industrial sector that produces a significant amount of waste, pollution and air emissions. However, the International Maritime Organization concentrates only on reducing emissions during the operational phase. In order to completely phase out emissions from the shipping industry, a life-cycle approach must be taken. The study implemented the proposed transdisciplinary energy management framework in a Bangladeshi shipyard. The framework aims to support shipyard decision makers in making rational and optimized decisions to make shipyards sustainable, while maintaining good product quality and reducing relative cost. This is achieved by applying the Fuzzy Analytical Hierarchy Process and Fuzzy Order of Preference by Similarity to Ideal Solution methods to identify optimal solutions. In addition to making shipyards more sustainable, the framework can enhance both the business and socio-economic prospects of the shipyard and promote the reputation of the shipyard and improve its competitiveness and, in line with this, lead to the promotion of nationally determined contributions under the Paris Agreement for States. The implementation of the framework shows that the political and legal discipline, the social criteria and the implementation of ISO 14001 and cyber security were the most important criteria and options for the yard's decision makers.