• Energy Research
• 7. Clean energy close
• GB close
• ES close
• Energy close

The energy considered as waste heat in industrial furnaces owing to inefficiencies represents a substantial opportunity for recovery by means of thermal energy storage (TES) implementation. Although conventional systems based on sensible heat are used extensively, these systems involve technical limitations. Latent heat storage based on phase change materials (PCMs) results in a promising alternative for storing and recovering waste heat. Within this scope, the proposed PCM-TES allows for demonstrating its implementation feasibility in energy-intensive industries at high temperature range. The stored energy is meant to preheat the air temperature entering the furnace by using a PCM whose melting point is 885 °C. In this sense, a heat transfer model simulation is established to determine an appropriate design based on mass and energy conservation equations. The thermal performance is analysed for the melting and solidification processes, the phase transition and its influence on heat transference. Moreover, the temperature profile is illustrated for the PCM and combustion air stream. The obtained results prove the achievability of very high temperature levels (from 700 to 865 °C) in the combustion air preheating in a ceramic furnace; so corroborating an energy and environmental efficiency enhancement, compared to the initial condition presenting an air outlet at 650 °C.

Considering recent environmental regulations, the need to adapt domestic biomass combustion systems to models that generate less emissions has gained relative importance. The present research proposes an analysis of the bed cooling effects on emission patterns, specifically focusing on the concentration, typology and morphological aspects of the released particles. The study was carried out by comparing the behaviour of a small-scale pilot plant with air stratification, with and without bed cooling. The results revealed an optimal behaviour of the facility with distributions of 30% primary-70% secondary air, accompanied by a significant decrease in emissions due to the reduction in the operating temperatures. More than 75% of the particles were retained in the bed on the cooled surfaces due to the effect of the prominent temperature gradient that was produced. Among the types of emitted particles (mostly with sizes below 0.1 μm), the presence of partial biomass degradation remnants was observed, representing three-quarters of the total collected matter. To a lesser extent, the presence of carbonaceous agglomerates was detected and usually in very compact clusters; however, in cases of high primary air supply, large amounts of immature soot were observed. Agencia Estatal de Investigación | Ref. RTI2018-100765-B-I00

In the current situation with the unprecedented deployment of clean technologies for electricity generation, it is natural to expect that storage will play an important role in electricity networks. This paper provides a qualitative methodology to select the appropriate technology or mix of technologies for different applications. The multiple comparisons according to different characteristics distinguish this paper from others about energy storage systems. Firstly, the different technologies available for energy storage, as discussed in the literature, are described and compared. The characteristics of the technologies are explained, including their current availability. In order to gain a better perspective, availability is cross-compared with maturity level. Moreover, information such as ratings, energy density, durability and costs is provided in table and graphic format for a straightforward comparison. Additionally, the different electric grid applications of energy storage technologies are described and categorised. For each of the categories, we describe the available technologies, both mature and potential. Finally, methods for connecting storage technologies are discussed.

Abstract The consumption of buildings for the production of heat is expected to decrease in Switzerland in the coming years, in particular following policies encouraging the refurbishment of buildings. This will notably have an impact on the natural gas network, in parallel with the penetration of electric-driven heat pumps. Through a detailed optimization scheme, the evolution of the natural gas (NG) distribution network is studied over a future period of forty years, i.e. up to 2050, on the territory of a large Swiss canton. By way of installing large shares of co-generation units, it is shown that the NG network does not lose its meshed structure, while continuing to play a central role in the production of heat and the generation of part of the additional electricity demand associated with the concomitant penetration of heat pumps. As a novel result, the developed optimization framework allows a detailed, geographically precise view of both the evolution of the NG network, as well as of the optimal location of selected technologies. The adoption of energy networks convergence in urban zones therefore can lead to relevant synergies, avoiding over-investments, increasing system resilience and fostering the use of efficient technologies.

Phase change materials (PCM) are used in many industrial and residential applications for their advantageous characteristic of high capacity of latent thermal storage by means of an isothermal process. In this context, it is very useful to have predictive mathematical models for the analysis of the thermal performance and for the thermal design of these layers. In this work, an experimental validation of an analytical model that resolves the steady periodic heat transfer problem in a finite layer of PCM is presented. The experimental investigation was conducted employing a PCM with thermophysical and thermochemical behavior very close to those hypothesized in the formulation of the analytical model. For the evaluation of the thermophysical properties of the PCM sample used, an experimental procedure created by the authors was employed. In all tests realized in a sinusoidal and non-sinusoidal periodic regime, the comparison between the measured and calculated trends of the temperature at different sample heights and of the surface heat fluxes show an excellent agreement. Moreover, also having verified the analytical total stored energy, the analytical model constitutes a valid instrument for the evaluation of the latent and sensible contribution and the trend in time of the position of the bi-phase interface. Peer Reviewed

Abstract Biomass materials are renewable sources that abundant worldwide due to natural plants and living organisms. Lignocellulosic biomass can be categorized as hardwood, softwood, agricultural wastes, and grasses. Agricultural residues those which of them have importance due to being produced in huge amounts in the worldwide annually. Food wastes and agricultural wastes are utilized either alternative use such as generating energy, fuels or disposal. However, disposal of these residues is follow out either scraping or burning way. This study aims to convert industrial agricultural origin biomass by using hydrothermal carbonization method to carbon-based material having high conductivity for use in supercapacitor production by using different activating chemicals. Hydrothermal carbonization was applied to different biomass samples such as nutshell, hazelnut shell, and corn cob. The elemental analysis of the obtained biochar was carried out and it was determined that the highest source of biomass was corn cob. The selected biochar has been chemically activated with different chemicals such as KOH, NaOH, H3PO4 and, ZnCl2. Advanced carbonization of activated biochar was carried out at 500, 600, 700 and 800 °C with 1, 1.5 and 2-h retention times. The resulting carbon-based products were mixed with KBr and identical pellets were prepared and their electrical conductivity values were measured. Electrical conductivity results, NaOH-800 °C-2h and ZnCl2-700 °C-1.5 h obtained from the process prepared from the biocidal pellets were determined to have the highest conductivity value. Brunauer–Emmett–Teller (BET) and Scanning Electron Microscope (SEM) analyses of the samples with the highest conductivity values were performed and surface morphologies were examined.