• Energy Research
• Closed Access close
• IT close
• GB close
• UA close
• Energy Conversion and Management close

Abstract The combined production of electricity, heat and cold by a polygeneration system connected to a district heating and cooling network can provide high energy utilization efficiency. The inherent complexity of simultaneous production of different services and the high variability in the energy demand make combined cooling and heating systems performance highly dependent on the operational strategy. In this paper, an operational optimization method based on the moving average of real-time measurements of energy demands and ambient conditions is proposed. Real energy demand data from a district heating and cooling network close to Barcelona, Spain, are used to test the method. A complex polygeneration system is considered, consisting of an internal combustion engine, a double-effect absorption chiller, an electric chiller, a boiler and a cooling tower. A detailed modelling of the system is provided, considering partial load behavior of the components and ambient conditions effects. Results of the real-time optimal management are discussed and compared to traditional operational strategies and to the ideal optimal management achievable with perfectly accurate forecast of energy demands. Moreover, the optimal width of the window adopted for the moving average of real-time data is identified.

Abstract The general objective of the investigation described in this article is the experimental testing of solar assisted dryers reported earlier. The tests show good technical results with a conventional energy consumption decrease of 27–80% and an average solar system efficiency of approx. 40%. From the experimental results, it can also be concluded that, with controlled removal of the moist air, improved product quality, significant reduction in drying time and mass losses, etc. result. The introduction of solar dryers seems to be a promising way for drying various agricultural products.

This paper describes a study of the combustion process in an industrial radiant tube burner (RTB), used in heat treating furnaces, as part of an attempt to improve burner performance. A detailed three-dimensional Computational Fluid Dynamics model has been used, validated with experimental test furnace temperature and flue gas composition measurements. Simulations using the Eddy Dissipation combustion model with peak temperature limitation and the Discrete Transfer radiation model showed good agreement with temperature measurements in the inner and outer walls of the burner, as well as with flue gas composition measured at the exhaust (including NO). Other combustion and radiation models were also tested but gave inferior results in various aspects. The effects of certain RTB design features are analysed, and an analysis of the heat transfer processes within the burner is presented.

Abstract The production of valued added fuels and chemicals via photocatalytic carbon dioxide reduction has attracted increasing attentions in recent years. Based on the traditional twin reactor configuration, a novel bubbling twin reactor is proposed to improve the conversion of carbon dioxide to methanol in this work. The multiphysical model for the bubbling twin reactor is developed and numerically simulated. The variations of the methanol production with the gas inlet flow velocity and gas inlet number are obtained. The results show that the bubbling twin reactor has a higher carbon dioxide conversion efficiency than the traditional one. Moreover, the methanol production subsequently increases as the gas inlet velocity increases. With the constant inlet gas volumetric flow rate, the production of methanol can be improved by increasing the gas inlet number.

Abstract Volumetric machines are the most suitable candidates to be used as expander in power units based on the Organic Rankine Cycle (ORC) thermodynamic concept, for waste heat recovery of Internal Combustion Engine in the on-the-road transportation sector. In particular, the technology of the Sliding Rotary Vane Expander (SRVE) shows intrinsic advantages thanks to their lower cost, shaping features, easier manufacturing and reliability and, generally speaking, very suitable operative conditions. Nevertheless, they show some disadvantages which are typical of volumetric machines, such as low capacity, limited expansion ratio and power lost by friction. Among the different technologies available to reduce the effects of these aspects (revolution speed increase, elliptical stators or with more complex geometries, tip blade optimization, rolling stators, etc.), the Dual-Intake Port (DIP) was assessed as a promising solution to enhance SVREs performance and operability. However, dual-intake port was still not conceived as design option. In this paper, a novel Sliding Vane Rotary Expander design concept involving a Dual Intake Port expander (DIP) option was developed and compared to the conventional Single Intake Port (SIP) one, under the same operating conditions. Thus, after an experimental comparison between SIP and DIP expanders, under the same conditions of mass flowrate, a theoretical expander model of the latter was validated on a set of experimental results. The model allows to outline the advantages of considering the dual port as a design option: for a specific flow rate and revolution speed, this option allows to reduce the friction losses, which represent a weak point of this volumetric machine. For a given mass flow rate of the working fluid, an additional feature is that it allows a sensible downsizing with respect to the SIP, with an axial dimension reduction up to 50%, ensuring additional weight and space saving. Despite the reduction of the dimensions, DIP produces a comparable mechanical power with respect to SIP, limiting the reduction to 8–10% of the SIP one with a 50% lower mechanical power loss due to friction. For the same flow rate, the added intake port determines a decrease of the intake pressure which is completely beneficial in terms of operating conditions of the overall recovery unit.

Abstract Aiming at designing biogas-to-electricity advanced systems, Solid Oxide Fuel Cells are promising candidates. They benefit from scalability on plant sizes that suit anaerobic digesters potentialities. For biogas-Solid Oxide Fuel Cells applications, the implementation of an external pre-reformer is usually considered. However, the possibility to perform direct fuel feeding to the Solid Oxide Fuel Cell offers new opportunities towards the realization of lean systems, which are competitive especially on small-scale installations (i.e. on-farm biogas-to-electricity conversion). In this frame, scientific literature is rather poor and, to cover this gap, system simulations are called for two reasons: first, to demonstrate the potential efficiency gain of new concepts; second, to provide a meaningful support for long-term experimental investigation on Solid Oxide Fuel Cells operated upon direct feeding of unreformed biogas. For that, the current study compares two system designs for biogas utilization into Solid Oxide Fuel Cells. The conventional one realizes biogas steam reforming prior the fuel cell, while the novel concept is based on direct feeding of partially upgraded biogas by means of carbon dioxide-separation membranes. As main outcome of the study, the system equipped with carbon dioxide-separation membranes achieves better performances than its conventional competitor does, scoring 51.1% energy efficiency and 52.3% exergy efficiency (compared to 37.2% and 38.6% respectively exhibited by the reformer-based system). Because of the lack a high endothermic process steps, the membrane-based system is also convenient whether heat recovery is required, producing a combined heat-and-power efficiency of 74.8% versus 47.0% obtained in the other system. Moreover, the results of a sensitivity analysis of the impact of membrane and reforming operating parameters on the overall system performances justify the convenience of adopting the solution of biogas direct feeding. Even in the hypothesis of a poorly performing membrane and an optimized reformer, the membrane-based system exhibits a gain in the system energy and combined heat-and-power efficiency of 25.2% and 34.9% respectively, with regard to the reforming-based concept. The forcefulness of this result is reinforced by a preliminary evaluation of capital expenditures, which represents a further economic advantage beside the economic revenue coming from a higher energy conversion efficiency.