• Energy Research
• engineering and technology close
• GB close
• IT close

Computational fluid dynamics (CFD) studies are carried out on a two-bladed vertical axis wind turbine operating at a wind speed of 8 m/s for tip speed ratios (λ) of 0.50–3.0. The blade is the NACA0021 airfoil with chord length 0.265 m and rotor radius 1 m. Basic sensitivity studies for various time step sizes are carried out. The results are validated against available measurement data from the literature. Excellent agreement is obtained for small λ up to optimum condition. For the higher tip speed ratios, the two-dimensional CFD computations predict higher results than the wind tunnel experiment, but they are very similar to the field measurement data. Wake characteristics are presented, showing that the wake becomes Gaussian at 5 times radius downstream of the rotor. It is shown that complex flow phenomena occur owing to dynamic stall onset, especially for the smaller tip speed ratio.

SYNOPSIS In Swaziland policies to alleviate fuelwood shortages have been low on the list of development priorities, as much of the land has extensive bush and tree cover. There are, however, major social and geographical imbalances in biomass resource supply—some areas of Swazi Nation Land are barren due to increasing population pressure and the subsequent demand for fuelwood. This paper will show, in detail, the methodology for the survey which was carried out in Swaziland to investigate the importance of accessibility in linking potential supply to demand. Physical location, land tenure and management practices are generally recognised as important factors to take into consideration when converting potential resources into realistic amounts of fuelwood supply. Guesswork, however, is often used to estimate the impacts of these factors on biomass supplies. A nation-wide study was made in order to obtain more information on the accessibility of resources on privately owned land; results of a household surv...

Abstract Energy system modelling can be used to assess the implications of different scenarios and support improved policymaking. However, access to data is often a barrier to starting energy system modelling in developing countries, thereby causing delays. This article therefore provides data that can be used to create a simple zero order energy system model for Mauritania, which can act as a starting point for further model development and scenario analysis. The data are collected entirely from publicly available and accessible sources, including the websites and databases of international organizations, journal articles, and existing modelling studies. This means that the dataset can be easily updated based on the latest available information or more detailed and accurate local data. These data were also used to calibrate a simple energy system model using the Open Source Energy Modelling System (OSeMOSYS) and two stylized scenarios (Fossil Future and Least Cost ) for 2020-2050. The assumptions used and results of these scenarios are presented in the appendix as an illustrative example of what can be done with these data. This simple model can be adapted and further developed by in-country analysts and academics, providing a platform for future work.

This work presents an innovative control architecture, which takes its ideas from the theory of adaptive control techniques and the theory of statistical learning at the same time. Taking inspiration from the architecture of a classical neural network with several hidden levels, the principle is to divide the architecture of the adaptive controller into three different levels. Each level implements an algorithm based on learning from data and therefore we can talk about learning concepts. Each level has a different task: the first to learn the required reference to the control loop; the second to learn the coefficients of the state representation of a model of the system to be controlled; and finally, the third to learn the coefficients of the state representation of the actual controller. The design of the control system is reported from both a rigorous and an operational point of view. As an application example, the proposed control technique is applied on a second-order non-linear system. We consider a servo-drive based on a brushless DC (BLDC) motor, whose dynamic model considers all the non-linear effects related to the electromechanical nature of the electric machine itself, and also an accurate model of the switching power converter. The reported example shows the capability of the control algorithm to ensure trajectory tracking while allowing for disturbance rejection with different disturbance signal amplitude. The implementation complexity analysis of the new controller is also proposed, showing its low overhead vs. basic control solutions.

Efficiency of energy resource use is a key factor for a sustainable energy future. By matching the exergy levels of supply and demand, Energy Quality Management (EQM) of building energy supply systems may achieve more efficient use of energy resources. Beyond this, environmental impact of energy supply systems is another essential issue. This work addresses the influence of EQM on CO 2 emissions in the operation optimization of a Distributed Energy System (DES). A multi-objective linear programming problem is formulated to reduce energy costs and increase the overall exergy efficiency. Total CO 2 emissions are evaluated for the optimized operation strategies of the DES. The operators of the DES can choose the operation strategy from the Pareto front, based on their priorities and also aware of effects on CO 2 emissions. Results demonstrate more efficient use of energy resources and reduction in CO 2 emissions through EQM, as compared with conventional energy supply systems.

This paper presents a tradeoff analysis in terms of accuracy and computational cost between different architectures of artificial neural networks for the State of Charge (SOC) estimation of lithium batteries in hybrid and electric vehicles. The considered layouts are partly selected from the literature on SOC estimation, and partly are novel proposals that have been demonstrated to be effective in executing estimation tasks in other engineering fields. One of the architectures, the Nonlinear Autoregressive Neural Network with Exogenous Input (NARX), is presented with an unconventional layout that exploits a preliminary routine, which allows setting of the feedback initial value to avoid estimation divergence. The presented solutions are compared in terms of estimation accuracy, duration of the training process, robustness to the noise in the current measurement, and to the inaccuracy on the initial estimation. Moreover, the algorithms are implemented on an electronic control unit in serial communication with a computer, which emulates a real vehicle, so as to compare their computational costs. The proposed unconventional NARX architecture outperforms the other solutions. The battery pack that is used to design and test the networks is a 20 kW pack for a mild hybrid electric vehicle, whilst the adopted training, validation and test datasets are obtained from the driving cycles of a real car and from standard profiles.

Exterior insulation finishing systems (EIFSs) can efficiently promote energy efficiency of buildings. In this study, an EIFS with high thermal efficiency is presented to improve the insulation behavior of building enclosure. Based on heat transfer analysis results, energy simulations of buildings with fire spread prevention structures were performed. Results revealed that heat flow through the wall increased by 10.3 % when using a metal rail to fix the insulation; in contrast, using non-combustible phenolic foam reduces heat flow by 37.4 %, satisfying the requirement for fire spread prevention structures. Additionally, the energy consumption decreased by 8.8 % when both mineral wool and phenolic foam were applied. Fire spread prevention structures are essential to improve the fire safety performance of buildings. This external insulation system efficiently promote energy saving in building; additionally, leveraging a phase change material to improve the thermal storage performance of the building can reduce energy consumption by up to 11.9 %.