• Energy Research
• engineering and technology close
• GB close
• IT close

In this paper a novel generalised modelling framework for multi-energy systems containing storage elements is combined with a multi-objective model predictive control. The control objective is to both minimise the economic cost of importing energy into the system as well as providing the service of smoothing the profile of the electrical energy imported thus levelling the load and reducing peak demand. The capabilities of the approach are demonstrated by its application to a representative case study based on two buildings at the University of Manchester. Results show that model predictive control is capable of simultaneously addressing minimisation of economic cost as well as smoothing the electrical energy import.

Abstract In this paper, the possibility of applying a Power System Stabilizer (PSS) via the governor-turbine system of a generating unit is studied for both single-machine and multimachine power systems. The results of analysis and simulation show that the conventional exciter-based PSS can be used in conjunction with the modern high-speed governor to suppress low-frequency oscillations in power systems. This arrangement of stabilizer possesses better robustness to the changes of power system operating conditions. Furthermore, in the environment of a multimachine power system, the control of PSS on the governor of every generator can be locally synthesized to stabilize the whole system, PSS design becomes much easier and simpler.

In the present work the influence of accelerated mineral carbonation on the leaching behaviour of basic oxygen furnace steel slag was investigated. The environmental behaviour of the material as evaluated through the release of major elements and toxic metals under varying pH conditions was the main focus of the study. Geochemical modelling of the eluates was used to derive a theoretical description of the underlying leaching phenomena for the carbonated material as compared to the original slag. Among the investigated elements, Ca and Si were most appreciably affected by carbonation. A very clear effect of carbonation on leaching was observed for silicate phases, and lower-Ca/Si-ratio minerals were found to control leaching in carbonated slag eluates as compared to the corresponding untreated slag sample as a result of Ca depletion from the residual slag particles. Clear evidence was also gained of solubility control for Ca, Mg and Mn by a number of carbonate minerals, indicating a significant involvement of the original slag constituents in the carbonation process. The release of toxic metals (Zn, V, Cr, Mo) was found to be variously affected by carbonation, owing to different mechanisms including pH changes, dissolution/precipitation of carbonates as well as sorption onto reactive mineral surfaces. The leaching test results were used to derive further considerations on the expected metal release levels on the basis of specific assumptions on the relevant pH domains for the untreated and carbonated slag.

The electric response to an external periodic voltage of small amplitude of dye-sensitized solar cells (DSCs) made up with an alternative architecture has been investigated. DSCs have been fabricated with a reversible sealing structure, based on microfluidic concepts, with a precise control on the geometric parameters of the active chamber. Cells with different electrolyte thicknesses have been characterized, without varying the thickness of the TiO2layer, both under illumination and in dark conditions. Measurements of the electric impedance have been performed in the presence of an external bias ranging from 0 V to 0.8 V. The experimental data have been analyzed in terms of a transmission line model, with two transport channels. The results show that the photovoltaic performances of the microfluidic cell are comparable with those obtained in irreversibly sealed structures, actually demonstrating the reliability of the proposed device.

Abstract In the last decade, there has been a growing trend towards flexible body wave energy converters (WECs) enabled by rubber-like elastomeric composite membrane structures that can simplify all aspects of WEC design. Currently, there are few literature studies detailing the implementations of membranes into WEC design. This paper aims to overcome this by reviewing the developments, material selection and modelling procedures for novel membrane based wave energy converters (mWECs), providing the reader with a comprehensive overview of the current state of the technology. In the first half of this paper, all of the possible WEC implementation areas are reviewed which include the primary mover, power take-off (PTO) and other sub-assembly systems. For the primary mover, the review has identified three main working surface approaches using membranes, these are: air-filled cells, water filled tubes and tethered carpets; which aim to reduce peak loads for enhanced reliability and survivability. In other areas, the PTO of WECs can benefit from using soft dielectric elastomer generators (DEGs) which offer a simpler designs compared with conventional mechanical turbomachinery. These have been implemented into the membrane working surface as well as replacing the PTO in existing WEC architectures. In the second half of the paper, a discussion is made on the material selection requirements with a few possible compositions presented. Following this, the potential modelling procedures for these devices is detailed. The device numerical models have altered existing procedures to take into account the non-linearities caused by the membrane interface and membrane PTO damping.

Abstract The housing growth programme could offer an opportunity for accelerating the deployment of decentralised renewable energy systems (DRES) in the UK. The Government hopes to leverage private sector investment into DRES as part of new housing projects. The aim of this paper is to assess whether current regulatory and funding frameworks are sufficient to achieve this. The question is explored by drawing on the experience of developers, local authorities, energy utilities and service companies operating in the largest housing growth region in the UK–Thames Gateway. Their experience suggests that the current low intervention approach will be insufficient to generate the shift required in both industries. In order to be more successful economic and regulatory instruments should focus on producers (house-builders and energy providers) rather than consumers (households). Tighter regulation is needed to ensure that producers have a responsibility to install DRES as part of new developments, to enable connection to the grid, to ensure a sustained financial return from investment and revenue is spent on the expansion of new renewable energy infrastructure. This regulatory framework must be under-pinned by substantial funds focused on producers. Greater intervention is needed if DRES is to be included in new housing development.

Abstract A new method for providing ventilation in large enclosures, which utilizes the principle of ‘selective withdrawal’ of contaminants while ensuring energy-efficiency and allowing a better use of space, is presented in this study. The concept is based on dividing the enclosed space ventilation-wise into separate zones using a combination of horizontal partitions by stratification and vertical partitions by temporary walls. This gives a high degree of flexibility in the use of available space. The relative influence of all the parameters on the flow patterns inside an enclosure is discussed in order to identify the design parameters that should be controlled to apply the technique successfully. An experimental study in a scale model was conducted, which provided a better understanding of the physical processes that occur in such enclosures. The influence of exhaust location on the flow field was studied in particular. It was found that by controlling the position of exhaust the stratification effects are enhanced and maintained at a desired level in order to achieve a successful utilization of the selective ventilation system.

The assessment of the ‘quality’ of built heritage is a complex transdisciplinary issue, which both public administrations and real estate developers need to carefully consider when making any interventions. Recent international climate regulations underline that currently around 75% of buildings in the EU are not energy efficient. In Italy, those inefficient buildings are more than 50 years old and, if subjected to retrofit interventions, risk being totally transformed and losing their historical value in favor of a more contemporary use. This work aimed to study the residential heritage of the second half of the 20th century in the real estate market and to understand if, how, and in what measure the building and architectonical qualities are recognized and monetized by buyers. The city of Turin was chosen as a study area, and residential building qualities were analyzed using two quality indicators to perform a GWR on market POIs. The results highlighted that housing historical qualities are not homogeneously recognized by the real estate market, in favor of green ones. This work can help both public and private bodies to identify which ‘invisible’ quality residential buildings are immediately exploitable for enhancement strategies, with more respectful retrofitting interventions and a modern protection policy.