• Energy Research
• Embargo close
• GB close
• NL close
• RU close

[EN] The objective of this article is to compare the behaviour of the most representative domestic hot water systems (DHW) in single-family buildings. The study evaluates the energy consumption, equivalent CO2 emissions and cost for each system over a 15-year life period. This analysis is carried out in four cli- matic zones across Europe to observe the influence of climatic conditions on the results. The four climatic zones are located in the cities of Athens, Madrid, London and Berlin. The analysed systems are: a) natural gas-fired instantaneous water heaters, b) electric storage water heater, c) solar thermal system with gas- fired instantaneous, d) solar thermal system with electric storage water heater, e) air-source heat pump, f) photovoltaic system with electric storage water heater, and g) photovoltaic system with air-source heat pump. This range of technologies covers the most likely solutions to be implemented across domestic buildings in Europe.The heat pump system (HPWH) with PV considering self-consumption shows the lowest environmen- tal impact in all zones, but is not an attractive investment in the coldest zones due to lower natural gas prices. Thermal solar systems have a high purchase and maintenance costs which do not compensate their energy savings. The PV HPWH system has a greater reduction of emissions and a lower cost than HPWH across a 15-year life. The gas boiler system has the lowest cost in a 15-year period in the coldest areas, despite having a greater environmental impact than the heat pump.(c) 2023 Elsevier B.V. All rights reserved.

AbstractCalcium oxide supported on ZrO2 is a highly active catalyst for base‐catalyzed reactions such as aldol‐type reactions and transesterification reactions. The role of key parameters during preparation, that is, impregnation versus precipitation, heat treatment, and metal oxide loading on the basicity and catalytic activity were investigated for CaO supported on ZrO2. An impregnation of 10 wt % CaO on monoclinic zirconia followed by heat treatment at 600 °C resulted in high activity for the self‐condensation reaction of acetone. An evaluation of a series of CaO/ZrO2 samples with different loadings showed that the activity increased for impregnated amounts per gram catalyst of 0–10 wt % CaO, and at higher loading the activity decreased as a result of a decrease in dispersion. The number of strong base sites (calculated from CO2 desorbed at temperatures higher than 625 °C) correlated with the activity. For MgO, CaO, SrO, and BaO on zirconia the catalytic activity increased as the ionic radius of the metal cation increased, suggesting the impact of base strength on catalytic performance.

Filament seals, such as brush seals and leaf seals, are investigated as a potential improved seal for gas turbine applications. As these seals operate in contact with the rotor, a good understanding of their stiffness is required in order to minimize seal wear and degradation. This paper demonstrates that the filament and complete seal stiffness is affected in comparable magnitudes by mechanical and aerodynamic forces. In certain cases, the aerodynamic forces can also lead to an overall negative seal stiffness which may affect stable seal operation. In negative stiffness, the displacement of the seal or rotor into an eccentric position causes a resultant force, which, rather than restoring the rotor to a central position, acts to amplify its displacement. Insight into the forces acting on the seal filaments is gained by investigating a leaf seal, which consists of a pack of thin planar leaves arranged around the rotor, with coverplates on either side of the leaf pack, offset from the pack surfaces. The leaf seal is chosen due to its geometry being more suitable for analysis compared to alternative filament seals such as the brush seal. Data from two experimental campaigns are presented which show a seal exhibiting negative stiffness and a seal exhibiting a stiffness reduction due to aerodynamic effects. An empirical model for the forces acting on leaf filaments is developed based on the experimental data, which allows separation of mechanical and aerodynamic forces. In addition a numerical model is developed to analyze the flow approaching the leaf pack and the interleaf flow, which gives an insight into the causes of the aerodynamic forces. Using the empirical and numerical models together, a full picture of the forces affecting leaf stiffness is created. Validation of the models is achieved by successfully predicting seal stiffness for a further data set across the full range of operating conditions. The understanding of aerodynamic forces and their impact on filament and seal stiffness allows for their consideration in leaf seal design. A qualitative assessment of how they may be used to improve seal operation in filament seals is given.

The lifetime and reliability of power transformers are primarily dependent on the hot-spot temperature in the windings, as temperature is the most important factor determining the insulation degradation rate. Key to removing the heat from the transformer is the radiator which must be carefully designed to keep the temperatures within limits under all operating conditions whilst minimizing the transformer size, weight and cost. This paper compares the analytical method used to predict the radiator performance with computational fluid dynamics (CFD) models in terms of heat dissipation. It is found that the analytical method and CFD models give similar results in the air natural (AN) cooling modes, whereas the analytical method overestimates the heat dissipation in the air forced (AF) cooling modes. Moreover, the thermal conduction effect in the radiator wall is investigated under different operating conditions and for different radiator sizes using the CFD models. The simulation results indicate that the radiator wall contributes to 6%-10% of the total heat dissipation under some circumstances and therefore should not be simply ignored in radiator models.

Selective removal of coatings by lasers can facilitate the reuse of coated tools in a circular economy. In order to optimise and control the process, it is essential to study the impact of process input variables on process performance. In this paper, coating removal from tooling was carried out using a picosecond a pulsed fibre laser, in order to investigate the effects of laser pulse energy, pulse frequency, galvo scanning speed and scanning track stepover. A fractional factorial design of experiments and analysis of variance was used to optimise the process; considering cleaning rate, specific energy consumption and surface integrity as assessed by changes in surface roughness and composition of the tooling after laser cleaning. The results shows synergy between cleaning rate and specific energy with the laser pulse frequency and galvo scanning speed as the two most significant factors, while the laser pulse energy had the greatest contribution to changes in surface composition. Based on extensive experiments, the relationship between processing rate and system specific energy consumption was mathematically modelled. The paper contributes a new specific energy model for laser cleaning and provides a benchmark of the process energy requirements compared to other manufacturing processes. Additionally, the generic scientific learning from this is that the rate of energy input is a key tool for maximising cleaning rate and minimising specific energy requirements, while the intensity of energy applied, is a key metric that influences surface integrity. More complex factors, influence the surface integrity.

AbstractTransition to a bio‐based economy will create new demand for biomass, e.g. the increasing use of bioenergy, but the impacts on existing markets are unclear. Furthermore, there is a growing public concern on the sustainability of biomass. This study proposes a methodological framework for mapping national biomass flows based on domestic production‐consumption and cross‐border trade, and respective share of sustainably‐certified biomass. A case study was performed on the Netherlands for 2010‐2011, focusing on three categories: (i) woody biomass, (ii) oils and fats, and (iii) carbohydrates. Between 2010‐2011 few major shifts were found, besides the increasing biofuel production. The share of sustainably‐certified feedstock is growing in many categories. Woody biomass used for energy amounted to 3.45 MT, including 1.3 MT imported wood pellets ( >85% certified). About 0.6 MT of oils and fats and 1.2 MT (estimation) of carbohydrates were used for biofuel production. It is assumed that only certified materials were used for biofuel production. For non‐energy purpose, more than 50% of woody biomass used was either certified or derived from recycled streams. Certified oils has entered the Dutch food sector since 2011, accounted for 7% of total vegetable oils consumption. It is expected that carbohydrates will also be certified in the near future. Methodological challenges encountered are: inconsistency in data definitions, lack of coherent cross‐sectorial reporting systems, low reliability of bilateral trade statistics, lack of transparency in biomass supply chains, and disparity in sustainability requirements. The methodology may be expanded for future projection in different scenarios. © 2013 Society of Chemical Industry and John Wiley & Sons, Ltd

Abstract: This study evaluates the economic and environmental benefits of implementing the proposed REcovered Nitrogen from manURE (RENURE) criteria as mineral fertiliser into the Nitrates Directive (ND) to facilitate the utilisation of minerals from manure. Implementing the RENURE amendment could significantly contribute to sustainability goals in an economic way, offering a 4.8 % reduction in economic costs in livestock-dense regions including Brittany (-0.7 %), Lombardy (-2.3 %), Flanders (-2.6 %), Lower Saxony (-4.7 %), Catalonia (-4.8 %), North-Rhine Westphalia (-4.8 %), and the Netherlands (-5.0 %). Through spatially explicit multi-agent modeling, the study revealed that the RENURE amendment not only promises economic benefits, but also enhances nitrogen circularity by 1.3 % and reduces greenhouse gas emissions by 6 % in these areas. These findings highlight the potential of nutrient recovery and reuse under RENURE to address both economic and environmental challenges, supporting the European Union's (EU) Farm-to-Fork strategy (F2F) goals of reducing nutrient emissions to the air and fertilizer use.