• Energy Research
• Closed Access close
• Embargo close
• GB close

Even with state of the art forecasting methods, the short-term generation of wind farms cannot be predicted with a high degree of accuracy. In a market situation, these forecasting errors lead to commercial risk through imbalance costs when advance contracting. This situation is one that needs to be addressed due to the steady increase in the amount of grid connected wind generation, combined with the rise of deregulated, market orientated electricity systems. In the presence of imbalance prices and uncertain generation, a method is required to determine the optimum level of contract energy to be sold on the advance markets. Such a method is presented here using Markov probabilities for a wind farm and demonstrates substantial reductions in the imbalance costs. The effect of market closure delays and forecasting window lengths are also shown.

Abstract In this paper, the possibility of applying a Power System Stabilizer (PSS) via the governor-turbine system of a generating unit is studied for both single-machine and multimachine power systems. The results of analysis and simulation show that the conventional exciter-based PSS can be used in conjunction with the modern high-speed governor to suppress low-frequency oscillations in power systems. This arrangement of stabilizer possesses better robustness to the changes of power system operating conditions. Furthermore, in the environment of a multimachine power system, the control of PSS on the governor of every generator can be locally synthesized to stabilize the whole system, PSS design becomes much easier and simpler.

Abstract The housing growth programme could offer an opportunity for accelerating the deployment of decentralised renewable energy systems (DRES) in the UK. The Government hopes to leverage private sector investment into DRES as part of new housing projects. The aim of this paper is to assess whether current regulatory and funding frameworks are sufficient to achieve this. The question is explored by drawing on the experience of developers, local authorities, energy utilities and service companies operating in the largest housing growth region in the UK–Thames Gateway. Their experience suggests that the current low intervention approach will be insufficient to generate the shift required in both industries. In order to be more successful economic and regulatory instruments should focus on producers (house-builders and energy providers) rather than consumers (households). Tighter regulation is needed to ensure that producers have a responsibility to install DRES as part of new developments, to enable connection to the grid, to ensure a sustained financial return from investment and revenue is spent on the expansion of new renewable energy infrastructure. This regulatory framework must be under-pinned by substantial funds focused on producers. Greater intervention is needed if DRES is to be included in new housing development.

Abstract A new method for providing ventilation in large enclosures, which utilizes the principle of ‘selective withdrawal’ of contaminants while ensuring energy-efficiency and allowing a better use of space, is presented in this study. The concept is based on dividing the enclosed space ventilation-wise into separate zones using a combination of horizontal partitions by stratification and vertical partitions by temporary walls. This gives a high degree of flexibility in the use of available space. The relative influence of all the parameters on the flow patterns inside an enclosure is discussed in order to identify the design parameters that should be controlled to apply the technique successfully. An experimental study in a scale model was conducted, which provided a better understanding of the physical processes that occur in such enclosures. The influence of exhaust location on the flow field was studied in particular. It was found that by controlling the position of exhaust the stratification effects are enhanced and maintained at a desired level in order to achieve a successful utilization of the selective ventilation system.

Melanin obtained from Aureobasidium pullulans and Cladosporium resinae was an efficient biosorbent for copper. Copper uptake could be expressed using various adsorption isotherms; melanin from A. pullulans obeyed Freundlich and Langmuir isotherms whereas C. resinae melanin followed the BET isotherm indicating a more complex type of adsorption than in A. pullulans. In general, uptake capacities of melanin were greater than for intact biomass and the higher uptake by pigmented rather than albino biomass could be correlated with the presence of melanin. Cu2+ was less readily desorbed from melanin by dilute mineral acids than from intact biomass and again, the relative ease of Cu2+ desorption from pre-loaded pigmented or albino biomass was correlated with the presence or absence of melanin. Mg2+ and Zn2+ appeared to be the most effective cations for desorption with Na+ and K+ the least effective. The addition of melanin to a coppercontaining culture of the albino strain of A. pullulans resulted in some reduction of toxicity.

Abstract Analytical and numerical investigation of methane–air lean combustibility limit (LCL) in reciprocal flow filtration combustion reactor was performed. Practically important parameters (heat loss coefficient, reactor length, pressure, particles size, porosity) were varied and corresponding sets of LCL curves were built. Existence of extremum at LCL – gas flow rate function is found. Numerical study shows that the porous media particle size is the most important factor for LCL control. Smaller particles provide lower LCL and reduce steepness of the growing branch of the LCL-gas flow rate function. For the particles smaller than 2 mm the corresponding LCL line goes down monotonously. High pressure in the system provides better LCL, which may be used for stabilization of the reactors operating at near LCL regimes.

Abstract Post-combustion solvent-based carbon capture is a promising technology that potentially can offset the greenhouse gas emissions from fossil-driven power generation systems. The challenge is that CO2 absorption (similar to other CCS technologies) imposes energetic penalties, and constrains the operational flexibility. In this paper, we build upon our recent contributions in the field (Sharifzadeh et al., 2016; Sharifzadeh and Shah, 2016), and study the dynamic response of such process to the electricity load changes in the power plant. The key research question is to investigate if the steady-state integrated process design and control framework applied in the previous studies, can also ensure controllability under a wide range of disturbances. The present study considers the mutual interactions between the power plant and capture process. Other features of interest include the implications of key design and operational decisions such as reboiler temperature, solvent circulation flow rate, solvent concentration and the rate of power load change or CO2 setpoint tracking for flexible process operation. The results suggest that the capture process exhibits a high degree of flexibility and the integrated design and control framework could be the key enabler for the commercialization of post-combustion solvent-based carbon capture.

Abstract A building integrated cooling facade is proposed in this paper. It is a fan-assisted system that consists of two vertical plenums. The first plenum was made of black aluminium transpired plate and a sandtile wall, while the second plenum is formed by the sandtile wall and the building wall. The aluminium plate served as a solar collector and the sandtile wall was an evaporative pad. The reverse side of the sandtile wall that contacted with the air in the second plenum was coated with a water-resistant layer, hence the air was cooled without adding any moisture into it. The facade cooling performance under various operating conditions is investigated through experiment and theoretical analyses. It is found that inlet water temperature is the key factor affecting the cooling performance. In terms of cooling efficiency, the energy consumption to generate 1 kW of cooling that cooling the air to 293 K is only 0.52 W, which is similar to the amount of energy required by some of the solar indirect evaporative cooling and desiccant cooling systems.