• Energy Research
• other engineering and technologies close
• 12. Responsible consumption close
• 6. Clean water close
• CN close
• IN close

Second-generation bioethanol can be produced from various lignocellulosic biomasses such as wood, agricultural or forest residues. Lignocellulosic biomass is inexpensive, renewable and abundant source for bioethanol production. The conversion of lignocellulosic biomass to bioethanol could be a promising technology though the process has several challenges and limitations such as biomass transport and handling, and efficient pretreatment methods for total delignification of lignocellulosics. Proper pretreatment methods can increase concentrations of fermentable sugars after enzymatic saccharification, thereby improving the efficiency of the whole process. Conversion of glucose as well as xylose to bioethanol needs some new fermentation technologies to make the whole process inexpensive. The main goal of pretreatment is to increase the digestibility of maximum available sugars. Each pretreatment process has a specific effect on the cellulose, hemicellulose and lignin fraction; thus, different pretreatment methods and conditions should be chosen according to the process configuration selected for the subsequent hydrolysis and fermentation steps. The cost of ethanol production from lignocellulosic biomass in current technologies is relatively high. Additionally, low yield still remains as one of the main challenges. This paper reviews the various technologies for maximum conversion of cellulose and hemicelluloses fraction to ethanol, and it point outs several key properties that should be targeted for low cost and maximum yield.

Acidogenic anaerobic fermentation route was explored for the production of bioethanol and volatile fatty acids (VFA) from the press mud (PM) obtained from sugar mill. Slurry was prepared from PM having 10% of total solids and the same was hydrolyzed under acidic thermal conditions. Both press mud slurry (PMS) and pre-treated press mud slurry (PTPMS) was used as feedstock with mixed microbial consortia (MMC) and enriched mixed microbial consortia (EMMC). Mix of bioethanol and VFA were obtained in all the four cases (PMS-MMC, PMS-EMMC, PTPMS-EMC and PTPMS-EMMC), but, bioethanol and VFA yield of 0.04 g/g and 0.27 g/g, respectively obtained from PTPMS with EMMC was found to be comparatively higher. Control experiments carried out with glucose yielded bioethanol and VFA of 0.042 g/g and 0.28 g/g, respectively demonstrating that the organism was using reducible sugars in the feedstock for the generation of bioethanol by simultaneously producing the VFA from COD.

Microwave-assisted alkali pre-treatment of wheat straw and its enzymatic hydrolysis were investigated and compared with the conventional alkali pre-treatment process. First, the effect of microwave power and pre-treatment time on the weight loss and composition of wheat straw was examined. The results show that the higher microwave power with shorter pre-treatment time and the lower microwave power with longer pre-treatment time had the same effect on the weight loss and composition at the same energy consumption. The comparison was then made between the effect of the microwave-assisted alkali pre-treatment and the conventional alkali one on the weight loss and composition of wheat straw. The wheat straw had a weight loss of 48·4% and a composition of cellulose 79·6%, lignin 5·7% and hemicellulose 7·8% after 25 min microwave-assisted alkali pre-treatment at 700 W, compared with a weight loss of 44·7% and a composition of cellulose 73·5%, lignin 7·2% and hemicellulose 11·2% after 60 min conventional alkali pre-treatment. The microwave-assisted alkali pre-treatment removed more lignin and hemicellulose from wheat straw with shorter pre-treatment time compared with the conventional alkali one. Finally, the enzymatic hydrolysis of pre-treated wheat straw (substrate concentration 50 g l−1, enzyme loading 20 mg g−1 substrate) was also investigated and the results indicate that the microwave-assisted alkali pre-treated wheat straw had higher hydrolysis rate, reducing sugar concentration and glucose content in the hydrolysate than the conventional alkali pre-treated one. Microwave-assisted alkali pre-treatment is a potential alternative of wheat straw pre-treatment for its enzymatic hydrolysis.

The current status and challenges associated with the production and utilization of cellulosic ethanol in Korea are reviewed in this paper. Cellulosic ethanol has emerged as a promising option for mitigating Korea's CO(2) emissions and enhancing its energy security. Korea's limited biomass resources is the most critical barrier to achieving its implementation targets for cellulosic ethanol. Efforts to identify new suitable biomass resources for cellulosic ethanol production are ongoing and intensive. Aquatic biomasses including macroalgae and plantation wastes collected in the Southeast Asia region have been found to have great potential as feedstocks for the production of cellulosic ethanol. R&D explorations into the development of technologies that can convert biomass materials to ethanol more efficiently also are underway. It is expected that cellulosic ethanol will be in supply from 2020 and that, by 2030, its use will have effectively reduced Korea's total gasoline consumption by 10%.

In the water-rich karst regions, high water and mud outbursts are common geological disasters in tunnel construction. To ensure the safe and smooth construction of tunnel projects, it is necessary to consider anti-water pressure, water inrush prevention and geological disasters during the design of tunnels. Based on the Yongfutun Tunnel Project, this paper studies the application and effect of radial grouting and curtain grouting, which involves those in high-water-pressure tunnels under double-layer support conditions. To obtain the effects and parameters of radial grouting and curtain grouting, the influences of different grouting ranges on the tunnel’s surrounding rocks and supporting structures were analyzed and the finite difference method was adopted. The results show that the radial grouting of the surrounding rock can notably improve the initial support of the tunnel, but the impact is less obvious when the grouting range exceeds 4 m. The design of radial grouting is recommended to be 4.0 m to 4.5 m. Curtain grouting can effectively reduce the external water pressure of the tunnel lining. The external water pressure of the grouting area is 23% greater than that without curtain grouting. Curtain grouting can slow down the infiltration of external water pressure. This is beneficial to the stress of the tunnel lining structure, but the improvement in initial support force is slight. Moreover, curtain grouting improves the safety reserve of the secondary lining by strengthening the self-stability ability of the surrounding rock. Meanwhile, the double-layer primary support can effectively share the external water pressure and surrounding rock pressure. This study provides a certain reference for the lining design of high-water-pressure tunnels.

Abstract Transportation de-carbonization is a complex problem involving the economy, population, technology and environment. Implementing the pathway simulation based on systematic methods will help to optimize the transportation sustainability plan. This study’s key motivation is that earlier research ignored the relationship between driving factors and the transmission process. To quantitatively identify the path and process of emission reduction, a hybrid system dynamics STIRPAT-SD model is proposed to explore the transportation optimization’s de-carbonization ability. This study fully considers the composition of elements and subsystems based on the STIRPAT theoretical model and visually shows the system’s feedback relationship. Transportation structural and technical optimization scenarios are set to identify the threshold reduction paths. It is found these optimization strategies have significant de-carbonization effects. And transportation structure policy has the highest de-carbonization efficiency, the emission intensity decreased by 9.1% under the TSS2 scenario (Transportation structure scenario). This study proposes a novelty model combining dynamic simulating processes with a significantly theoretical model to improve simulation and factor composition accuracy. And the joint scenario setting identifies the most effective de-carbonization pathway and clarifies the threshold of all possible pathways. Research findings can effectively track, test, predict the achievement of policy goals, and provide policy optimization references for the sustainable development related to the transportation system in practice.

Abstract In this paper, coupled governing equations were proposed to simulate three-dimensional heat conduction and moisture transport in the nuclear waste repository. Because there will be a large temperature gradient near inner and outer boundaries of the bentonite buffer layer, and the heat driven moisture transport is introduced in the governing equation of moisture transport. By applying the Fourier and Laplace transforms, the governing equations were converted to the Bessel equations, and the Laplace-domain solutions to temperature and moisture distributions were derived through the inverse Fourier transform. The reliability of the proposed solutions was verified through comparative analysis with the line heat source model. These analytical solutions were applied to obtain the evolutions of temperature field and moisture distribution near the waste canister. Finally, a sensitivity study was performed to analyze the effects of relevant parameters on the heat driven moisture transport.

This study aims to explore the application of fractional order chaotic system (FOCS), based on the T-S fuzzy model, in the design of secure communication (SC) and this SC system’s role in the construction of efficiency evaluation system for dispatching operation of energy saving and power generation under a low carbon economy (LCE). First, the definition of fractional order differential equations and the stability theory of FOCS are discussed. T-S fuzzy control is introduced to analyse the stability of FOCS. Then, based on the adaptive synchronisation theory, the combined FOCS is designed for SC, and the performance of the system constructed here is analysed in a MATLAB environment. Next, an evaluation index system of the dispatching operation effect of energy saving and power generation under LCE is constructed. The confidential communication system constructed here is used to transmit the index data. The particle swarm optimisation (PSO) algorithm is then used to optimise the back propagation neural network (BPNN) model. The BPNN algorithm based on PSO (PSO-BPNN) is obtained, and the evaluation model is constructed. After training this model, it is applied to the evaluation of the dispatching operation effect for energy saving and power generation in 10 provinces in China. The simulation results show that the FOCS based on the T-S fuzzy model can acquire the criterion of system stability. Furthermore, the constructed SC system can effectively undertake the secure transmission of square and sine waves. The performance of the PSO-BPNN model seems to be better than other algorithms. After analysing the data on energy saving and power generation from 10 provinces in China using this model, the comprehensive evaluation value of province 5 is found to be the highest and good (0.802), while that of province 4 is the lowest and general (0.600). Summarising, the FOCS based on T-S fuzzy model constructed here is applied to the design of SC. This can improve the confidentiality of data transmission and reduce the transmission error. Moreover, the BPNN evaluation model based on PSO can effectively achieve the evaluation of the dispatching operation effect of energy saving and power generation under LCE.