• Energy Research
• 7. Clean energy close
• 6. Clean water close
• IN close
• JP close
• UA close

AbstractTwenty sodium-cooled fast reactors (SFRs) have provided valuable experience in design, licensing, and operation. This paper summarizes the important safety criteria and safety guidelines of intermediate sodium systems, steam generators, decay heat removal systems and associated construction materials and in-service inspection. The safety criteria and guidelines provide a sufficient framework for design and licensing, in particular by new entrants in SFRs.

Mobile edge computational power faces the difficulty of balancing the energy consumption of many devices and workloads as science and technology advance. Most related research focuses on exploiting edge server computing performance to reduce mobile device energy consumption and task execution time during task processing. Existing research, however, shows that there is no adequate answer to the energy consumption balances between multi-device and multitasking. The present edge computing system model has been updated to address this energy consumption balance problem. We present a blockchain-based analytical method for the energy utilization balance optimization problem of multi-mobile devices and multitasking and an optimistic scenario on this foundation. An investigation of the corresponding approximation ratio is performed. Compared to the total energy demand optimization method and the random algorithm, many simulation studies have been carried out. Compared to the random process, the testing findings demonstrate that the suggested greedy algorithm can improve average performance by 66.59 percent in terms of energy balance. Furthermore, when the minimum transmission power of the mobile device is between five and six dBm, the greedy algorithm nearly achieves the best solution when compared to the brute force technique under the classical task topology.

Anode with good electrocatalytic capabilities is more specifically required to reduce the ohimic losses during microbial fuel cell (MFC) operation. Highly conductive polymers viz., Polyaniline (PANi) and Polyaniline/Carbon nanotube (PANi/CNT) composite were prepared by in situ oxidative chemical polymerization method. Anodes were fabricated independently by coating PANi and CNT/PANi composites on the surface of SSM. The fabricated electrodes were evaluated as anode against stainless steel mess (SSM) as cathode during MFC operation. Maximum bioelectricity generation was observed in SSM-PANi/CNT-anode with power density of 48 mW/m2 and COD removal efficiency of 80% compared with SSM-PANi-anode (38 mW/m2; 65%) and SSM-anode (28 mW/m2; 58%). Bioelectrochemical characterization of the electrode materials using cyclic voltammetry and electrochemical impedance spectroscopy showed high electrocatalytic activity of PANi/CNT composite electrode. The study concluded the efficiency of PANi/CNT composite electrodes as bioanode in operation of MFCs towards achieving increased bioelectricity production along with wastewater treatment.

This review presents recent advancements in high-voltage rechargeable aqueous batteries employing water-in-salt and modified water-in-salt electrolytes.

Partial discharge (PD) measurement using electromagnetic waves by antennas is a promising technique for diagnosing the insulation performance of gas-insulated switchgear (GIS). In order to establish highly sensitive diagnosis techniques of GIS insulation, frequency characteristics of electromagnetic waves, which are determined by GIS apertures such as insulating spacers and bushings, should be clarified. In this paper, we measure the electromagnetic waves radiated from different GIS apertures and also analyze them using the transient analysis program "PSpice." Comparing the measurements with the theoretical analyses, we investigate the relationship between the GIS aperture configuration and the radiated electromagnetic wave spectrum from the aperture. We also discuss how the aperture condition contributes to the radiation characteristics of electromagnetic waves. Finally, we conclude that the electromagnetic waves radiated from the GIS aperture are based on different radiation mechanisms in frequency.

Abstract. The last half century has witnessed the increasing trend of renewable energy utilization with solar photovoltaic (PV) systems as one of the most popular option. Solar PV continues to supplement the main grid in powering both commercial establishments (mainly for reduced electricity expense) as well as residential houses in isolated areas (for basic energy requirement such as for lighting purposes). The objective of this study is to assess the available solar PV power (PPV) potential considering the effects of high temperature, dust and snow in the Asia Pacific region. The PPV potential was estimated considering the effects of the said meteorological parameters using several satellite data including shortwave radiation from Advanced Himawari Imager 8 (AHI8), MOD04 aerosol data from Moderate Resolution Imaging Spectroradiometer (MODIS), precipitation rate from Global Satellite Mapping of Precipitation (GSMaP), air temperature from NCEP/DOE AMIP-II Reanalysis-2 data, and snow water equivalent (SWE) from Microwave Scanning Radiometer for the Earth Observing System (AMSR-E). The model is validated by comparing its outputs with the measured PV power from two solar PV installations in Bangkok, Thailand and Perth, Australia. Results show that maximum PPV is estimated at 2.5 GW (cell efficiency of 17.47%) for the region with the maximum decrease in PPV estimated to be about < 2%, 22% and 100% due to high temperature (temperature coefficient of power = 0.47%/K), dust and snow, respectively. Moreover, areas in India and Northern China were observed to experience the effects of both dust and temperature during March-April-May (MAM) season. Meanwhile, countries located in the higher latitudes were severely affected by snow while Australia by high temperature during Dec-Jan-Feb (DJF) season. The model has a mean percentage prediction error (PPE) range of 5% to18% and 7% to 23% in seasonal and monthly estimations, respectively. Outputs from this study can be used by stakeholders of solar PV in planning for small-scale or large-scale solar PV projects in the solar rich region of Asia Pacific.

Abstract Biodiesel has gained the forefront of our focus on renewable transportation fuels. This article provides a comprehensive review on the sources used as feedstock and their classification based on generation or type (edible, non-edible, waste resources and animal fats) along with a variety of classical and modern oil extraction techniques. The technical aspects of the various biodiesel production methods currently implemented to the best of our knowledge are discussed here, which include in-situ biodiesel production, both catalysed (homogeneous and heterogeneous systems) and uncatalysed classical production approaches, with emphasis on how each of these approaches are affected by their reaction parameters. The review also highlights the observed drawbacks of each process with a view to assessing the implementation of supercritical and superheated technologies as an alternative, economically feasible advancement. Supercritical process (SCP) has shown great prospect in the obtainment of high quality biodiesel from a wide range of high to low grade feedstock with minimal impacts on the presence of water or FFAs (free fatty acids). From available literature it is shown that these do not affect the process significantly, and various other supercritical fluids such as methyl acetate, tert-butyl methyl ether (MTBE) and dimethyl carbonate can also be used to avoid glycerol formation. The process however, suffers from high initial implementation cost being the most prominent drawback, among others like thermal degradation of the fuel. Another promising technique, the superheated vapour technology (SHV) has emerged as an alternative, with limited literature proving the superiority of either of these processes to be inconclusive. In future works, researchers need to look into various aspects such as developing a spiral reactor for heat recovery, using software based optimization for eliminating redundant experiments analysing production cost for industrial scale-up and improving the fuel’s oxidative stability by adding antioxidants for convenient long-term storage and use.

Abstract Heat exchanger is one the most essential heat transfer equipment in thermal area. On that heat transfer and effectiveness enhancement by using nano particles is recently developing method. In this study enhancement of effectiveness focused by using nano particles mixed with cold fluid used in the heat exchanger. Hot fluid is water with 200 °C flow into Counter flow heat exchanger and the cold fluid is mixed with 5% of nano particles which is combination of Aluminium oxide and Magnesium oxides with equal proportion. The inlet temperature of the cold fluid is maintained at 30 °C throughout the experiments. The temperatures of each place need to measure are obtained by the thermocouples connected on the particular portion of the setup. There is different mass flow rate of cold fluid passed in each successive experiment for the same mass flow rate and inlet temperature of the hot fluid. The consequent exit temperatures of hot and cold fluids were measured and considered for the mathematical calculations of the outcome of the experiments.