• Energy Research
• engineering and technology close
• 6. Clean water close
• AU close
• IT close

Abstract Economically harvesting energy from a microbial fuel cell (MFC), increasing its electrical power production, and developing its role as a practical energy supply, needs a low-cost and high-performance design of the MFC compartments. According to this strategy, a novel monolithic membrane electrode assembly (MEA) was fabricated and evaluated as an air–cathode in a single-chamber MFC (SCMFC). The MEA was made of bacterial cellulose (BC), conductive multi-walled carbon nanotubes (CNT), and nano-zycosil (NZ). BC, as a nano-celluloses with oxygen barrier property, can maintain anaerobic conditions for the anode compartment. Binder-less CNT coating on BC avoids costly binders such as poly-tetra fluoro ethylene (PTFE) and Nafion and decreases the MEA charge transfer resistance. NZ, as a very cheap modifier, not only prevents the anolyte leakage but also provides more MEA’s active sites for the oxygen reduction reaction (ORR). The electrochemical performance of the MEA was compared to a PTFE- based gas diffusion electrode (GDE) in the SCMFC. The MEA cell provided a pulse power density of 1790 mW/m2, roughly twice as high as the pulse power density of GDE (920 mW/m2). SCMFC’s internal resistance decreased from 1.84 KΩ (with GDE) to 0.8 KΩ (with MEA). Also, the cell’s columbic efficiency increased from 4.2% (with GDE) to11.7% (with MEA). Additionally, the capacitance of the MEA (65 mF) was much higher than the value for GDE (0.73 mF). Thus, the MEA compared to the GDE showed higher performance in the SCMFC for electricity generation and wastewater treatment at a lower cost.

Improving access to safe drinking water can result in multi-dimensional impacts on people's livelihood. This has been aptly reflected in the Millennium Development Goals (MDG) as one of the major objectives. Despite the availability of diverse and complex set of technologies for water purification, pragmatic and cost-effective use of the same is impeding the use of available sources of water. Hence, in country like India simple low-energy technologies such as solar still are likely to succeed. Solar stills would suffice the basic minimum drinking water requirements of man. Solar stills use sunlight, to kill or inactivate many, if not all, of the pathogens found in water. This paper provides an integrated assessment of the suitability of domestic solar still as a viable safe water technology for India. Also an attempt has been made to critically assess the operational feasibility and costs incurred for using this technology in rural India.

Abstract Italy reformed its water and sanitation services in 1994. The strategy aimed at transforming public entities, financed by the central budget, into self-sufficient professional companies regulated at arms' length. Nearly 20 years after, the reform has failed to deliver (despite some partial success). Italians have been divided in two parties: those blaming public sector inefficiencies and calling for competitive tendering; and those refusing to privatize water and willing to go back to the fiscal budget. In this article, we suggest that both parties are wrong. Underperformance is not related to the ownership structure of water companies, but rather to poor regulatory design and lack of understanding of the regulatory requirements that are implicit in the management model chosen, namely the concession contract.

In this work we assess the pathways for environmental improvement by the coal utilization industry for power generation in Australia. In terms of resources, our findings show that coal is a long term resource of concern as coal reserves are likely to last for the next 500 years or more. However, our analysis indicates that evaporation losses of water in power generation will approach 1000 Gl (gigalitres) per year, equivalent to a consumption of half of the Australian residential population. As Australia is the second driest continent on earth, water consumption by power generators is a resource of immediate concern with regards to sustainability. We also show that coal will continue to play a major role in energy generation in Australia and, hence, there is a need to employ new technologies that can minimize environmental impacts. The major technologies to reduce impacts to air, water and soils are addressed. Of major interest, there is a major potential for developing sequestration processes in Australia, in particular by enhanced coal bed methane (ECBM) recovery at the Bowen Basin, South Sydney Basin and Gunnedah Basin. Having said that, CO2 capture technologies require further development to support any sequestration processes in order to comply with the Kyoto Protocol. Current power generation cycles are thermodynamic limited, with 35-40% efficiencies. To move to a high efficiency cycle, it is required to change technologies of which integrated gasification combined cycle plus fuel cell is the most promising, with efficiencies expected to reach 60-65%. However, risks of moving towards an unproven technology means that power generators are likely to continue to use pulverized fuel technologies, aiming at incremental efficiency improvements (business as usual). As a big picture pathway, power generators are likely to play an increasing role in regional development; in particular EcoParks and reclaiming saline water for treatment as pressures to access fresh water supplies will significantly increase.

Abstract Aquatic centres are large and complex buildings which include at least one indoor swimming pool and several amenities such as gymnasium, cafe, office, spa, sauna and stadium. There are only a few studies that have investigated the energy and water use of aquatic centres. This study developed energy and water benchmarks for aquatic centres in Victoria, Australia using data from 22 aquatic centres. Statistical regression based benchmarking method was used to identify relevant correlations and significances of several variables in regards to the energy and water use of aquatic centres. The analysis indicated that conditioned usable floor area and the number of visitors have the strongest correlation and significance to the energy and water use of aquatic centres respectively. No strong correlation was found between energy and water use. The proposed energy benchmark for aquatic centres ranges between 648 kWh/m2 and 2283 kWh/m2 (conditioned usable floor area) and the proposed water benchmark for aquatic centres ranges between 11 L/Visitor and 110 L/Visitor. An attempt to identify energy and water efficient characteristics of aquatic centres was also undertaken using the detailed data collected.

This paper proposes a two-part process for producing biocrude with reduced impurities. The biocrude was produced from hydrothermal liquefaction (HTL) of Spirulina sp. and Tetraselmis sp. in a batch reactor at both 300 and 350°C, 5min, and 16%w/w solid feed composition. The resultant biocrudes were vacuum distilled at a maximum temperature of 360°C. It was shown that biocrude quality could be enhanced without using catalyst by vacuum distillation (VD). The biocrude yield for Spirulina sp. was 36wt% at 300°C, 42wt% at 350°C, and for Tetraselmis sp. was 34wt% at 300°C, and 58wt% at 350°C. VD of Spirulina sp. biocrude obtained at 300 and 350°C led to 62 and 67wt% distilled biocrudes yield, respectively. VD of Tetraselmis sp. biocrude obtained at 300°C was 70wt%, and 73wt% at 350°C. The higher heating values (HHV) increased from 32MJ/kg to 40MJ/kg. There were substantial reductions in oxygen, metallic content, and boiling point ranges in distilled biocrudes.

ABSTRACTAn overview is given of an International Atomic Energy Agency Coordinated Research Project (CRP) on the treatment of irradiated graphite (i-graphite) to meet acceptance criteria for waste disposal. Graphite is a unique radioactive waste stream, with some quarter-million metric tons worldwide eventually needing to be disposed of. The CRP has involved 24 organizations from 10 Member States. Innovative and conventional methods for i-graphite characterization, retrieval, treatment and conditioning technologies have been explored in the course of this work, and offer a range of options for competent authorities in individual Member States to deploy according to local requirements and regulatory conditions.

The enhanced oil recovery technique of low-salinity (LS) water flooding is a topic of substantial interest in the petroleum industry. Studies have shown that LS brine injection can increase oil production relative to conventional high-salinity (HS) brine injection, but contradictory results have also been reported and an understanding of the underlying mechanisms remains elusive. We have recently developed a steady-state pore network model to simulate oil recovery by LS brine injection in uniformly wetted pore structures (Watson et al., Transp. Porous Med. 118, 201-223, 2017). We extend this approach here to investigate the low-salinity effect (LSE) in heterogeneously wetted media. We couple a model of capillary force-driven fluid displacement to a novel tracer algorithm and track the salinity front in the pore network as oil and HS brine are displaced by injected LS brine. The wettability of the pore structure is modified in regions where water salinity falls below a critical threshold, and simulations show that this can have significant consequences for oil recovery. For networks that contain spanning clusters of both water-wet and oil-wet (OW) pores prior to flooding, our results demonstrate that the OW pores contain the only viable source of incremental oil recovery by LS brine injection. Moreover, we show that a LS-induced increase in microscopic sweep efficiency in the OW pore fraction is a necessary, but not sufficient, condition to guarantee additional oil production. Simulations suggest that the fraction of OW pores in the network, the average network connectivity and the initial HS brine saturation are key factors that can determine the extent of any improvement in oil recovery in heterogeneously wetted networks following LS brine injection. This study highlights that the mechanisms of the LSE can be markedly different in uniformly wetted and non-uniformly wetted porous media.

The global energy demand is growing substantially. Clean and secure energy supply is a must for our civilization's sustainable development. Solar and wind energy is growing fast and can contribute significantly to meet the goals set by many countries to reduce greenhouse gas emissions. A deep and wide investigation of the environmental impact of solar and wind energy is important before any solar or wind plants' construction is made. In this study, the literature is reviewed to summarize the environmental impact of solar and wind energy systems in terms of the following factors; land use, water consumption, impact on biodiversity, visual and noise effects, health issues, and impact on micro climate. Although the benefits of solar and wind energy are obvious and great, negative perception of these technologies can inhibit their wide penetration in some regions. This review paper includes a critical and an inclusive analysis of solar and wind energy’s environmental impact and may serve as an important tool to conduct a proper environmental impact assessment. This critical analysis may serve also as a tool for developers, policy, and decision-when planning future solar and wind farms.