• Energy Research
• 7. Clean energy close
• 12. Responsible consumption close
• CN close
• US close
• DE close
• IT close
• EU close

AbstractMembrane Technology and Research, Inc. has proposed a hybrid system combining amine scrubbing with membrane technology to reduce energy cost. Previous studies of CO2 absorption mainly focused on coal-fired flue gas with 12% CO2. However, in the hybrid process, the CO2 in the flue gas can be enriched to 20%. Natural gas turbines will have flue gas with as little as 3% CO2。 Based on the arrangement, the hybrid amine/membrane system provides a gas to the system that has double the CO2 concentration of normal flue gas, reduces the volume of gas sent to the capture unit, or reduces the removal requirements for the capture unit.The objective of this work is to minimize the total energy use of stripping concentrated piperazine (PZ) at rich loading when treating flue gas from 3 to 20% inlet CO2. The base-case stripping configuration is the advanced flash stripper with warm rich bypass and cold rich exchanger bypass. . This configuration includes two split cross-exchangers in series, a convective steam heater, a smaller stripper column, a low residence time flash tank, and stripping at high temperature to produce CO2 at 5 to 17bar. Rich loading in 5 and 8m PZ was varied from 0.37 to 0.43mol CO2/mol N. For each rich loading, lean loading was optimized to minimize the total equivalent work. The “Independence” model for PZ in Aspen Plus® was used to simulate the stripping performance.Because 5m PZ has a lower viscosity than 8m PZ, it can achieve a reduced approach temperature in the cross exchanger. The total energy performance for 5m PZ is practically the same as 8m PZ, even though the capacity of 5m PZ is lower. Significantly more energy is required to regenerate solvents with lower rich loading. As CO2 rich loading increases, the equivalent work requirement decreases for the same loading difference between rich and lean.Stripping data for 24 cases, including heat duty, equivalent work, CO2 output pressure, and optimal cold and warm rich bypass were used to build a correlation with CO2 rich and lean loading. The Second Law efficiency based on the ratio of stripping minimum work and total ideal work was introduced to make the most of stripping work. The Second Law efficiency has a maximum value at a specific CO2 loading.

Abstract Transient thermal behaviors of ultra-supercritical steam turbine control valves during the cold start warm-up process of steam turbine systems were comprehensively studied using conjugate heat transfer (CHT) simulation. The geometrical configurations and boundary conditions used in simulation were identical to the field setup in a thermal power plant. The simulated temperature variations were first validated using measurements by the flush-mounted thermocouples inside the solid valve bodies. The CHT simulation implementing the shear stress transport (SST) turbulence model demonstrated good agreement with the field data, and the overall numerical errors were below 10%; however, the numerical errors of the simulation, which used empirical heat transfer coefficients at the fluid–solid interfaces, reached 40%. The determined temperature differences between the cold valve bodies with the hot steam flow decreased significantly. Specifically, the temperature differences along the inner wall surfaces of the valve bodies decreased to less than 50 °C. Further investigation of the transient heat flux distributions and Nusselt number distributions confirmed that the unsteady flow behaviors, such as the alternating oscillations of the annular wall-attached jet, the central reverse flow and the intermediate shear layer instabilities, enhanced the fluid–solid heat convection process and thus contributed to the warming up of the solid valve bodies.

Abstract This study sought to quantify and characterize cassava waste as fuel. The wastes from three cultivars were collected to study and were divided into three distinct parts of the cassava plant: seed stem, thick stalks, and thin stalks. Physical and chemical analyzes were carried out to determine the elemental composition of the waste: volatile matter; fixed carbon; ash; moisture; lignin; cellulose; hemicellulose; ash composition and higher heating value were determined. We conducted a thermogravimetric analysis in oxidizing and inert atmospheres to study the behavior of the waste as fuel. The root productivity obtained ranged from 7.7 to 13.0 t ha−1 yr−1 on a dry basis (db), and the ratio between waste and roots varied from 0.36 to 0.91. The physical and chemical properties of cassava waste are analogous to those of woody biomass regarding the elemental composition, the higher heating value, and thermogravimetric analysis. Ash content varied from 2.5% to 3.5%, reaching around 6.0% in samples unwashed. Approximately 60% of the ashes are alkali oxides, especially P2O5, K2O, and CaO, which have low melting points. The alkali index calculated suggests that there is a strong tendency that the combustion process leads to ash fouling and the formation of ash deposits.

Flexible butyl interconnection segments are synthetically incorporated into an electronically conductive poly(pyrene methacrylate) homopolymer and its copolymer. The insertion of butyl segment makes the pyrene polymer more flexible, and can better accommodate deformation. This new class of flexible and conductive polymers can be used as a polymer binder and adhesive to facilitate the electrochemical performance of a silicon/graphene composite anode material for lithium ion battery application. They act like a “spring” to maintain the electrode mechanical and electrical integrity. High mass loading and high areal capacity, which are critical design requirements of high energy batteries, have been achieved in the electrodes composed of the novel binders and silicon/graphene composite material. A remarkable area capacity of over 5 mAh/cm2 and volumetric capacity of over 1700 Ah/L have been reached at a high current rate of 333 mA/g.

AbstractTo estimate the life cycle cost of thermal power equipments in engineering, this paper established a comprehensive evaluation model of life cycle cost with the life cycle breakdown and cost breakdown structure. Based on the model, this paper defined the cost elements of the thermal power equipment, analyzed influences of the thermal power equipment. Finally, the model is applied to an instance to estimate various cost categories in each life phase, which were summed up to the life cycle cost of the thermal power equipment.

A template‐agent can affect defect formation as well as influence interface properties, due to the rapid growth of perovskite film from the solution. Herein, diethylammonium iodide (DAI) is used as an effective template‐agent to control the perovskite crystallization during preparation. It is found that a very small amount of DAI in chlorobenzene (CB) can slow down the perovskite growth of the CH3NH3PbI3 (MAPbI3) film with more large grain size and compacted crystal‐grains resulting in the lesser grain boundaries (GBs) in favor of carrier transport in perovskite solar cells (PSCs). Moreover, some redundant PbI2 can be digested to form DA2PbI4. One part of DA2PbI4 can form the sub‐grains with the composition of (DA2PbI4)0.2(PbI2)0.8 to passivate the GB defects, and other part can cover the surface to passivate the surface defects in large MAPbI3 grains. Using an optimized DAI concentration of 0.5 mg mL−1 in CB solution, the corrsponding MAPbI3 PSC achieves an increased power conversion efficiency of 20.31% with suppressed current–voltage hysteresis. This DAI passivation strategy provides a simple approach to effectively assist the grain‐growth for improved device performance.

The rapid development of advanced metering infrastructure provides a new data source—building electrical load profiles with high temporal resolution. Electric load profile characterization can generate useful information to enhance building energy modeling and provide metrics to represent patterns and variability of load profiles. Such characterizations can be used to identify changes to building electricity demand due to operations or faulty equipment and controls. In this study, we proposed a two-path approach to analyze high temporal resolution building electrical load profiles: (1) time-domain analysis and (2) frequency-domain analysis. The commonly adopted time-domain analysis can extract and quantify the distribution of key parameters characterizing load shape such as peak-base load ratio and morning rise time, while a frequency-domain analysis can identify major periodic fluctuations and quantify load variability. We implemented and evaluated both paths using whole-year 15-minute interval smart meter data of 188 commercial office building in Northern California. The results from these two paths are consistent with each other and complementary to represent full dynamics of load profiles. The time- and frequency-domain analyses can be used to enhance building energy modeling by: (1) providing more realistic assumptions about building operation schedules, and (2) validating the simulated electric load profiles using the developed variability metrics against the real building load data.

Abstract The prime purpose of this work is to prepare a novel kind of Pickering interfacial solid catalysts for biodiesel production to meet the requirements of highly efficiency and environmental benign. To achieve this goal, the core–shell P[xSPA-yDABCO]@SiO2@Fe3O4 composite materials with a shell of photo-responsive and base catalytic sites were manufactured by means of layer-by-layer fabrication method. The modified materials, entirely characterized by transmission electron microscopy (TEM), scanning electron microscope (SEM), Fourier transform infrared (FT-IR) spectra, X-ray powder diffraction (XRD) and magnetization versus magnetic (VSM) techniques, demonstrated sufficient catalytic active sites and photo-responsive sites. Among all the so-prepared catalysts, P[3SPA-2DABCO]@SiO2@Fe3O4 performs extremely well and can stabilize soybean oil-in-methanol Pickering emulsion for 24 h, achieving a biodiesel yield up to 98.2% at a catalyst dosage of 5 wt% after the reaction time of 5 h at 60 °C. Furthermore, the double responsive solid catalyst can be readily separated from the mixture of reaction by an external magnet and UV irradiation, and still presented superior catalytic activity after 6 cycles.

The electro-hydraulic servo pump control system (EHSPCS) is a volume control system that uses a permanent magnet synchronous motor (PMSM) with a fixed displacement pump to directly drive and control the hydraulic cylinder. The energy transmission law of the system is very complicated due to the transformation of electrical, mechanical and hydraulic energy as well as other energy fields, and qualitative analysis of the energy transfer efficiency is difficult. Energy transfer analysis of the EHSPCS under different working conditions and loads is proposed in this paper. First, the energy flow transfer mechanism was analyzed, and the mathematical and energy transfer models of the key components of the system were established to explore the energy characteristic state transition rule. Second, a power bond diagram model was built, its state equation and state matrix were deduced, and a system simulation model was built. Finally, combined with the EHSPCS experimental platform, simulation experiments were carried out on the dynamic position following and steady-state position holding conditions of the system, and the variation rules of the power of each energy characteristic state and the system energy transfer efficiency under different loads were obtained. The research results provide a foundation for the study of power matching and energy-saving mechanism of the EHSPCS.

Abstract In this paper, we analyze the rationale for an energy policy mix when the European Emissions Trading Scheme (ETS) is considered from a public choice perspective. That is, we argue that the economic textbook model of the ETS implausibly assumes (1) efficient policy design and (2) climate protection as the single objective of policy intervention. Contrary to these assumptions, we propose that the ETS originates from a political bargaining game within a context of multiple policy objectives. In particular, the emissions cap is negotiated between regulators and emitters with the emitters' abatement costs as crucial bargaining variable. This public choice view yields striking implications for an optimal policy mix comprising RES supporting policies. Whereas the textbook model implies that the ETS alone provides sufficient climate protection, our analysis suggests that support for renewable energies (1) contributes to a more effective ETS-design and (2) may even increase the overall efficiency of climate and energy policy if other externalities and policy objectives besides climate protection are considered. Thus, our analysis also shows that a public choice view not necessarily entails negative evaluations concerning efficiency and effectiveness of a policy mix.