• Energy Research
• engineering and technology close
• IT close
• DE close
• Energies close

Research on corona discharge, shared by physics, chemistry and electrical engineering, has not arrested yet. As a dissipative process, the development of corona increases the resistive losses of transmission lines and enhances the line capacitance locally. Introducing additional losses and propagation delay, along the line, non-linearity and non-uniformity of the line parameters; therefore, corona should not be neglected. The present work is meant to provide the reader with comprehensive information on the corona macroscopic phenomenology and development, referring to the most relevant contributions in the literature on this subject. The models proposed in the literature for the simulation of the corona development are reviewed in detail, and sensitivity curves are provided to highlight their dependence on the input parameters.

The hygrothermal behaviour of an internally insulated historic wall is still hard to predict, mainly because the physical characteristics of the materials composing the historic wall are unknown. In this study, the hygrothermal assessment of an internally thermal insulated masonry wall of an historic palace located in Ferrara, in Italy, is shown. In situ non-destructive monitoring method is combined with a hygrothermal simulation tool, aiming to better analyse and discuss future refurbishment scenarios. In this context, the original U-value of the wall (not refurbished) is decreased from 1.44 W/m2K to 0.26 W/m2K (10 cm stone wool). Under the site specific conditions of this wall, not reached by the sun or rain, it was verified that even in the absence of vapour barrier, no frost damage is likely to occur and the condensation risk is very limited. Authors proposed further discussion based on simulation. The results showed that the introduction of a second gypsum board to the studied technology compensated such absence, while the reduction of the insulation material thickness provides a reduction of RH peaks in the interstitial area by 1%; this second solution proved to be more efficient, providing a 3% RH reduction and the avoidance of further thermal losses.

The proposed special issue (SI) has invited submissions related to renewable energy, energy storage, power converters and electric drive systems for electrified transportation and smart grid applications [...]

Shading the greenhouses is necessary in summer to reduce the solar radiation load. This however generates a considerable amount of thermal radiation heat load that needs to be removed via cooling systems. This study aimed to evaluate the effect of different shading configurations on the solar and thermal radiation in a greenhouse. Nets at four different locations were employed to shade the roof and side-walls of a polycarbonate, mechanically ventilated greenhouse. The spectral radiative properties of all these plastic materials were measured in short and long wave spectrum bands. The net solar and thermal radiations and air temperature were measured outside and inside two identical shaded and unshaded greenhouses. The results showed that external roof-shading is desirable, as it reduced the generated thermal radiation in the greenhouse by 21% and 15% during the day and night time, respectively and reduced the greenhouse air temperature during the day. The internal shading (roof and side walls) is undesirable, since it drastically increased the generated thermal radiation in the greenhouse by 147% and strongly increased the greenhouse air temperature during the day. Shading the side-walls is not recommended because it significantly reduces the transmitted solar radiation in the morning and afternoon (when the outside irradiance is low) and is useless at around noon when the outside irradiance is extremely high.

Coal will continue to be the main energy source in China for the immediate future, although the environmental pollution and ecological impacts of each stage in the full life cycle of coal mining, transportation, and combustion generate large quantities of external costs. The Late Permian coals in southwestern (SW) China usually contain high amounts of fluorine (F), arsenic (As), and ash, which together with high-F clays cause abnormally high levels of endemic fluorosis, As poisoning, and lung cancer in areas where coal is mined and burned. In this paper, we estimate the external costs of the life cycle of coal. The results show that the externalities of coal in SW China are estimated at USD 73.5 billion or 284.3 USD/t, which would have accounted for 6.5 % of the provincial GDP in this area in 2018. The external cost of human health accounts for 87.2% of the total external costs, of which endemic skeletal fluorosis diseases and related lung cancers have the most important impact. Our study provides a more precise estimate of externalities compared with its counterparts in other provinces in China. Therefore, several policy recommendations would be proposed to internalize the external cost.

Direct Numerical Simulations (DNS) have been conducted to study the response of initially laminar spherical premixed methane–air flame kernels to successively higher turbulence intensities at five different equivalence ratios. The numerical experiments include a 16-species/25-step skeletal mechanism for methane oxidation and a multicomponent molecular transport model. Highly turbulent conditions (with integral Reynolds numbers up to 4513) have been accessed. The effect of turbulence on the physical properties of the flame, in particular its consumption speed Sc, which is an interesting measure of the turbulent flame speed ST has been investigated. Local quenching events are increasingly observed for highly turbulent conditions, particularly for lean mixtures. The obtained results qualitatively confirm the expected trend regarding correlations between u′/SL and the consumption speed: Sc first increases, roughly linearly, with u′/SL (low turbulence zone), then levels off (bending zone) before decreasing again (quenching limit) for too intense turbulence. For a fixed value of u′/SL, Sc/SL varies with the mixture equivalence ratio, showing that additional parameters should probably enter phenomenological expressions relating these two quantities.

The biogas production technology has improved over the last years for the aim of reducing the costs of the process, increasing the biogas yields, and minimizing the greenhouse gas emissions. To obtain a stable and efficient biogas production, there are several design considerations and operational parameters to be taken into account. Besides, adapting the process to unanticipated conditions can be achieved by adequate monitoring of various operational parameters. This paper reviews the research that has been conducted over the last years. This review paper summarizes the developments in biogas design and operation, while highlighting the main factors that affect the efficiency of the anaerobic digestion process. The study’s outcomes revealed that the optimum operational values of the main parameters may vary from one biogas plant to another. Additionally, the negative conditions that should be avoided while operating a biogas plant were identified.