• Energy Research
• 7. Clean energy close
• IT close
• GB close
• AU close
• Energies close

As a relatively mature technology, biomass molded fuel (BMF) is widely used in distributed and centralized heating in China and has received considerable government attention. Although many BFM incentive policies have been developed, decreased domestic traditional fuel prices in China have caused BMF to lose its economic viability and new policy recommendations are needed to stimulate this industry. The present study built a regionalized net present value (NPV) model based on real production process simulation to test the impacts of each policy factor. The calculations showed that BMF production costs vary remarkably between regions, with the cost of agricultural briquette fuel (ABF) ranging from 86 US dollar per metric ton (USD/t) to 110 (USD/t), while that of woody pellet fuel (WPF) varies from 122 USD/t to 154 USD/t. The largest part of BMF’s cost composition is feedstock, which accounts for up 50%–60% of the total; accordingly a feedstock subsidy is the most effective policy factor, but in consideration of policy implementation, it would be better to use a production subsidy. For ABF, the optimal product subsidy varies from 26 USD/t to 57 USD/t among different regions of China, while for WPF, the range is 36 USD/t to 75 USD/t. Based on the data, a regional BMF development strategy is also proposed in this study.

Nowadays, heating using wood, briquettes, or pellets is a curious replacement to fossil fuels such as coal, oil, or gas. Unfortunately, the combustion of biofuels, especially in low-power boilers with unstable operating conditions, releases a lot of gas pollutants (e.g., carbon monoxide (CO), nitric oxide (NO), and various organic compounds) that are usually generated due to the incomplete product combustion. The combustion of biofuel in grate boilers with top-down ignition is a new approach, popular in society (mainly used for coal fuels), which improves the combustion process and reduces the amount of pollutants emitted. This study evaluated the impact of ignition techniques on the emission level of gas pollutants during the combustion of wood logs, briquettes, and pellets of pine in grate-based charging boilers. The combination of top ignition mode with pinewood logs allowed us to achieve a reduction of 6% in CO and sulfur dioxide (SO2) emission into the atmosphere. However, the combination of top-down ignition mode with pellets and briquettes produced, in fully operational conditions, 1- to 18-fold higher levels of CO and SO2 respectively, than bottom-up ignition, after an initial period of low level CO and SO2 emissions. During the tests (mainly with ignition from top), substantial emissions of NO were observed of up to 400 mg·m−3 at 10% O2. Therefore, further research is required to decrease emission related to the content of nitrogen in biomass. In this respect, research of impact on the combustion temperature of such emissions is needed.

The decarbonisation of heating in the United Kingdom is likely to entail both the mass adoption of heat pumps and widespread development of district heating infrastructure. Estimation of the spatially disaggregated heat demand is needed for both electrical distribution network with electrified heating and for the development of district heating. The temporal variation of heat demand is important when considering the operation of district heating, thermal energy storage and electrical grid storage. The difference between the national and urban heat demands profiles will vary due to the type and occupancy of buildings leading to temporal variations which have not been widely surveyed. This paper develops a high-resolution spatiotemporal heat load model for Great Britain (GB: England, Scotland a Wales) by identifying the appropriate datasets, archetype segmentation and characterisation for the domestic and nondomestic building stock. This is applied to a thermal model and calibrated on the local scale using gas consumption statistics. The annual GB heat demand was in close agreement with other estimates and the peak demand was 219 GWth. The urban heat demand was found to have a lower peak to trough ratio than the average national demand profile. This will have important implications for the uptake of heating technologies and design of district heating.

The proposed special issue (SI) has invited submissions related to renewable energy, energy storage, power converters and electric drive systems for electrified transportation and smart grid applications [...]

Both electrical and thermal efficiencies combine in determining and evaluating the performance of a PV/T collector. In this study, two PV/T systems consisting of poly and monocrystalline PV panels were used, which are connected from the bottom by a heat exchanger consisting of a spiral tube through which a nanofluid circulates. In this study, a base fluid, water, and ethylene glycol were used, and iron oxide nanoparticles (nano-Fe2O3) were used as an additive. The mixing was carried out according to the highest specifications adopted by the researchers, and the thermophysical properties of the fluid were carefully examined. The prepared nanofluid properties showed a limited effect of the nanoparticles on the density and viscosity of the resulting fluid. As for the thermal conductivity, it increased by increasing the mass fraction added to reach 140% for the case of adding 2% of nano-Fe2O3. The results of the zeta voltage test showed that the supplied suspensions had high stability. When a mass fraction of 0.5% nano-Fe2O3 was added the zeta potential was 68 mV, while for the case of 2%, it reached 49 mV. Performance tests showed a significant increase in the efficiencies with increased mass flow rate. It was found when analyzing the performance of the two systems for nanofluid flow rates from 0.08 to 0.17 kg/s that there are slight differences between the monocrystalline, and polycrystalline systems operating in the spiral type of exchanger. As for the case of using monocrystalline PV the electrical, thermal, and total PV/T efficiencies with 2% added Fe2O3 ranged between 10% to 13.3%, 43–59%, and 59 to 72%, respectively, compared to a standalone PV system. In the case of using polycrystalline PV, the electrical, thermal, and total PV/T efficiencies ranged from 11% to 13.75%, 40.3% to 63%, and 55.5% to 77.65%, respectively, compared to the standalone PV system. It was found that the PV/T electrical exergy was between 45, and 64 W with thermal exergy ranged from 40 to 166 W, and total exergy from 85 to 280 W, in the case of using a monocrystalline panel. In the case of using polycrystalline, the PV/T electrical, thermal, and total exergy were between 45 and 66 W, 42–172 W, and 85–238 W, respectively. The results showed that both types of PV panels can be used in the harsh weather conditions of the city of Baghdad with acceptable, and efficient productivity.

Shading the greenhouses is necessary in summer to reduce the solar radiation load. This however generates a considerable amount of thermal radiation heat load that needs to be removed via cooling systems. This study aimed to evaluate the effect of different shading configurations on the solar and thermal radiation in a greenhouse. Nets at four different locations were employed to shade the roof and side-walls of a polycarbonate, mechanically ventilated greenhouse. The spectral radiative properties of all these plastic materials were measured in short and long wave spectrum bands. The net solar and thermal radiations and air temperature were measured outside and inside two identical shaded and unshaded greenhouses. The results showed that external roof-shading is desirable, as it reduced the generated thermal radiation in the greenhouse by 21% and 15% during the day and night time, respectively and reduced the greenhouse air temperature during the day. The internal shading (roof and side walls) is undesirable, since it drastically increased the generated thermal radiation in the greenhouse by 147% and strongly increased the greenhouse air temperature during the day. Shading the side-walls is not recommended because it significantly reduces the transmitted solar radiation in the morning and afternoon (when the outside irradiance is low) and is useless at around noon when the outside irradiance is extremely high.

In underground mining, it is not currently feasible to forecast a coal burst incident. A coal burst usually includes suddenly abrupt energy release in line with the significant deformed shape in a coal mass as well as coal ejection. The major source of the released energy is the energy stored in the coal. The effect of geological characteristics in the coal on the possible released energy due to material and joint damping is classified as a current silent issue. Therefore, innovative research is needed to understand the influence of coal’s joint and cleat characters (directions and densities) on the possible energy release and/or dissipation. A simple and novel analytical solution is developed in this paper to calculate the amount of released energy due to varying joint density. A broad validation is conducted by comparing the outcomes of the developed analytical model with the results of a three-dimensional numerical simulation using the commercial discrete element package 3DEC. An appropriate agreement has been observed between the results from the numerical modelling and the suggested closed form solution. The paper derives a novel analytical solution to calculate the amount of released energy in coal with different joint densities.

The prevailing need for a more sustainable management of natural resources depends not only on the decisions made by governments and the will of the population, but also on the knowledge of the role of energy in our society and the relevance of preserving natural resources. In this sense, critical work is being done to instill key concepts—such as the circular economy and sustainable energy—in higher education institutions. In this way, it is expected that future professionals and managers will be aware of the importance of energy optimization, and will learn a series of computational methods that can support the decision-making process. In the context of higher education, this paper reviews the main trends and challenges related to the concepts of circular economy and sustainable energy. Besides, we analyze the role of simulation and serious games as a learning tool for the aforementioned concepts. Finally, the paper provides insights and discusses open research opportunities regarding the use of these computational tools to incorporate circular economy concepts in higher education degrees. Our findings show that, while efforts are being made to include these concepts in current programs, there is still much work to be done, especially from the point of view of university management. In addition, the analysis of the teaching methodologies analyzed shows that, although their implementation has been successful in favoring the active learning of students, their use (especially that of serious games) is not yet widespread.