• Energy Research
• engineering and technology close
• 7. Clean energy close
• 13. Climate action close
• 11. Sustainability close
• 6. Clean water close
• IT close

Abstract To achieve the EU climate and energy objectives, a transition towards a future sustainable energy system is needed. The integration of the huge potential for industrial waste heat recovery into smart energy system represents a main opportunity to accomplish these goals. To successfully implement this strategy, all the several stakeholders' conflicting objectives should be considered. In this paper an evolutionary multi-objective optimization model is developed to perform a sustainability evaluation of an energy system involving an industrial facility as the waste heat source and the neighbourhood as district heating network end users. An Italian case study of heat recovery from a steel casting facility shows how the model allows to properly select the district heating network set of users to fully exploit the available waste energy. Design directions such as the thermal energy storage capacity can be also provided. Moreover, the model enables the analysis of the trade-off between the stakeholders’ different perspectives, allowing to identify possible win-win solutions for both the industrial sector and the citizenship.

-

Abstract Breastshot water wheels are gravity hydraulic machines employed in low head sites. The scope of this work is to test the performance of a breastshot water wheel with two geometric inflow configurations: a sluice gate at different openings and two vertical overflow weirs. With the sluice gate, the maximum efficiency of the plant is 75%, constant over a wide range of flow rates, while the efficiency with the weir is increasing in the same flow rate range. Therefore, the wheel with the weir can exploit higher water volumes, and also it performs better at high power input. In practical applications, the inflow configuration can be effectively controlled to optimize the operative working conditions of breastshot water wheels, depending on the external hydraulic ones. The experimental results are also discussed in dimensionless terms, in order to support engineers in the design of similar breastshot water wheels.

Telecommunication is a prerequisite for the Smart Grid. Several technologies are available on the market, but there is not a general agreement about which of them, or combination of them, that can enable most of the services for the distribution grid automation. The paper describes the approach of 7th Framework Program European Project INTEGRIS which relies on the hypothesis that there is not a single technology with an optimal trade-off between cost of investment and performances for all use cases and topologies of a distribution grid. It rather suggests to mesh several technologies (with focus on the Broadband Power Line, the Wi-Fi and the Fiber Optics) to cover all the segment of the distribution grid. This concept has been experimentally validated in two field demonstrators in Italy and in Spain. This paper presents the results of tests on the latency and the throughput.

Abstract Economically harvesting energy from a microbial fuel cell (MFC), increasing its electrical power production, and developing its role as a practical energy supply, needs a low-cost and high-performance design of the MFC compartments. According to this strategy, a novel monolithic membrane electrode assembly (MEA) was fabricated and evaluated as an air–cathode in a single-chamber MFC (SCMFC). The MEA was made of bacterial cellulose (BC), conductive multi-walled carbon nanotubes (CNT), and nano-zycosil (NZ). BC, as a nano-celluloses with oxygen barrier property, can maintain anaerobic conditions for the anode compartment. Binder-less CNT coating on BC avoids costly binders such as poly-tetra fluoro ethylene (PTFE) and Nafion and decreases the MEA charge transfer resistance. NZ, as a very cheap modifier, not only prevents the anolyte leakage but also provides more MEA’s active sites for the oxygen reduction reaction (ORR). The electrochemical performance of the MEA was compared to a PTFE- based gas diffusion electrode (GDE) in the SCMFC. The MEA cell provided a pulse power density of 1790 mW/m2, roughly twice as high as the pulse power density of GDE (920 mW/m2). SCMFC’s internal resistance decreased from 1.84 KΩ (with GDE) to 0.8 KΩ (with MEA). Also, the cell’s columbic efficiency increased from 4.2% (with GDE) to11.7% (with MEA). Additionally, the capacitance of the MEA (65 mF) was much higher than the value for GDE (0.73 mF). Thus, the MEA compared to the GDE showed higher performance in the SCMFC for electricity generation and wastewater treatment at a lower cost.

Abstract This article focuses on the results obtained by the enforcement of a original greenhouse gas emissions policy, issued in recent years in several municipalities in Northern Italy. The Municipality of Reggio Emilia was one of the firsts in Italy to develop and adopt a voluntary building energy-consumption certification method called Ecoabita, aiming to promote energy efficiency in buildings over its jurisdiction. Several reasons make this project innovative: first, the certification method has been processed through and verified by a quality international agency, secondly the procedure is assisting financial-incentive policies both on mandatory (European Directive 2002/91/CE) and voluntary basis (Municipality Protocol Ecoabita), finally it allows to obtain eligible credits for avoided emissions that can be negotiated on the CO2 exchange market. With specific reference to Reggio Emilia case, acknowledged the amount of actions, that are normally scheduled in the municipality throughout a year, it has been evaluated the benefit, in terms of environmental improvement, descended from the protocol, also projecting their trend in future years up to 2020 as well, demonstrating the scheduled interventions are fundamental in sought of the achievement of the Kyoto and Copenhagen commitments. The entire procedure has been developed in accordance to the parameters given by UNFCCC for these kinds of analyses and has been recently confirmed to be one of the most accurate international accounting procedure by a survey developed by the scientific committee of the European Project LIFE-LAKS.

Abstract This paper presents a non-stoichiometric equilibrium model for the simulation of biomass downdraft gasifiers. The chemical equilibrium is determined by minimizing the Gibbs free energy. Five elements characterize the biomass and 15 chemical species are considered in the syngas. The model calculates the lower heating value of the syngas and the relative abundances of gasification products. An advantage of this model is that it can easily calculate not only the concentrations of the main gasification products, but also the concentrations of minor product, especially the pollutant chemical species containing Nitrogen and Sulfur. To analyse the model behaviour, a sensitivity analysis on process parameters is presented. The model is validated by comparing its results with the results of simulation carried out with a stoichiometric model and with experimental data found in literature. Finally, the model is applied to the study of the gasification of forest waste.

Abstract Probability density functions (PDFs) are normally used to describe wind speed distribution for the proper selection of wind turbines in a given location. The identification of a suitable PDF is fundamental for accurately assessing the wind energy potential and designing the wind farms. To achieve this objective, the use of a mixture of two truncated normal distributions (MTTND), defined for v ≥ 0 and obtained by linearly combining two normal distributions with different means and variances, is proposed in this work for the representation of the wind speed PDF. The distribution is a function of five parameters, does not require a high computational burden and allows the representation of wind calm hours (v = 0). The use of the MTTND allows an accurate estimation to be obtained of the experimental discrete distribution of the probability density and cumulative probability, and the characteristic statistical quantities used to estimate the available energy and the performance indicators in the selection of both the site and wind turbine. The validity of the use of the MTTND was verified by comparison with the most widespread PDFs in the scientific literature: Weibull, Rayleigh, lognormal, gamma, inverse Gaussian and Burr. This comparison was developed using experimental wind speed data relating to five Italian locations and a location in Colorado (USA) belonging to the National Renewable Energy Laboratory. For each location, the parameters of each PDF were obtained with the least squares non-linear regression method. The results of the comparisons, in terms of the coefficient of determination R2 and root mean square error (RMSE) for goodness of fit and in terms of relative error in the calculation of the statistical quantities, show that the use of the MTTND gives rise to greater accuracy than a conventional wind speed PDF.

Abstract Reaching universal access to electricity by 2030 requires a massive deployment of mini-grids in rural areas of developing countries. Among the many challenges hindering this process, there are the high uncertainties in assessing demand patterns in rural communities, the costs of field survey campaigns, and the absence of ample and reliable datasets coming from existing projects. This paper tries to address these issues by presenting and discussing a database of load profiles from sixty-one off-grid mini-grids from developing countries worldwide, gathered from the literature, private developers and fieldworks, and reported with technical, socio-economic and geographical characterization factors. A clustering procedure led to the identification of five archetypal load profile clusters, which are presented and analyzed together with their load duration curves. Subsequently, the distribution among the clusters of the various characterization factors selected is studied. The proposed approach allows to widen the range of load profiles usually considered, and to seek correlations between the load profile shapes, the peak power and average energy consumption per connection, the number of customers, the age of measurement, geographical position, operator model, type of tariff and generation technologies present. This work establishes a first step in the creation of a shared database for load profiles of rural mini-grids, helping to overcome the lack of available data and difficulties of demand assessment, proposing original insights for researchers to understand load patterns, and contributing to reduce risks and uncertainties for mini-grid developers.