• Energy Research
• Restricted close
• Open Source close
• 7. Clean energy close
• IT close

Dolomite-based binders are characterised by interesting technical and environmental features. For their synthesis, sources of both CaO and MgO are required. The idea developed in this work is to couple the synthesis of dolomite-based binders, starting from a natural dolomite, through the concept of concentrated solar energy (needed to drive the endothermal dolomite calcination process) in fluidised bed reactors. To this end, a fluidised bed system, where the concentrated solar radiation is mimicked by the use of Xe-lamps (short-arc), has been set up and operated. Natural dolomite (sieved in the 420-590 ?m size range) was calcined at a nominal temperature of 850 °C, and bed temperature profiles during solar-driven calcination were investigated. Then, four binders were prepared by mixing slaked dolomite (obtained from the hydration of solar calcined dolomite) with either blast furnace slag or coal fly ash as supplementary cementitious materials. The binders were hydrated for curing times ranging from 7 to 56 days. X-ray fluorescence, X-ray diffraction and combined differential thermal and thermogravimetric analyses were employed as characterisation techniques both to analyse the chemical composition of starting materials and to investigate the evolution of the hydration in the four systems.

In this paper a grid-tied photovoltaic (PV) cascaded H-bridge (CHB) inverter with embedded storage units is proposed. The multi-input single-output inverter architecture allows a distributed maximum power point tracking (DMPPT) approach, thus mitigating the mismatch effects. The energy storage units (ESUs) embedded at each dc-link provides more flexibility to the power circuit compensating for the inherent variability of the PV sources. The proposed power system ensures a continuous power supply to the grid also in case of PV power fluctuations due to irradiance conditions as well as to the MPPT. In particular, the presence of a storage element allows a voltage sweep on the PV source to be implemented, thus guaranteeing the maximization of PV energy harvesting, with no detrimental effect on the power delivery to the utility network. The numerical results, carried out on a single-phase nineteen-level PV CHB inverter, reveal the improved performance of the proposed design and control technique.

The safeguard of power equipments is assuming a major role in the deregulated electricity market, where a malfunctioning power system could be responsible for serious damages to a large number of system operators having access to the shared energy resource. In this context thermal monitoring of power cables represents a key issue in evaluating the risks associated with a given load management policy especially during emergency conditions. In particular this demands for reliable assessment models that should be able to predict the transient thermal behaviour when the load exceeds the nameplate value. In this connection the application of both simplified and detailed power cable thermal models is often complicated by the presence of uncertainties affecting the tolerances of the input data. The effect of these uncertainties could influence the final solution to a considerable extent. A comprehensive tolerance analysis is therefore required in order to incorporate the effect of data uncertainties into the thermal modelling process. To address this problem, in the paper the employment of interval mathematic is proposed. Several numerical results are presented and discussed in order to assess the effectiveness of the proposed methodology which offer a rough qualitative insight of the solution in a very short time, comparable to the time required for a deterministic numerical simulation.

In this article is presented the preliminary evaluation of the performance of radiation transmission of glass block, used in support of photovoltaic cells, investigating different internal surface points of the block, which are subject to different shading during daylight hours. The aim is to establish how the edging setting, the only opaque element, can reduce the amount of light radiation during the day, introducing in this way a reduction of efficiency of the entire generation system. The generation system can be based on traditional photovoltaic cells or on the most suitable dye sensitized solar cells. An experimental measurement setup employing a microprocessor-based instrument has been created and a set of measures have been carried out. The measures prove that the shading effect at different irradiation angles do not affect significantly the lighting over the PV cell.

Nowadays, many islands worldwide are lack of electrical energy. Thus, it is convenient to exploit available renewable energy sources, among which sea waves near the islands. This paper focuses on the power conversion system coupled with an offshore wave energy device, such as an improved linear generator, to be used for sea wave energy harvesting. Particularly, the design of the linear generator has been proposed to improve the energy efficiency of the entire system. The proposed power conversion system is composed by two Boost Rectifier (BR) directly coupled to the linear generator, and one Voltage Source Inverter (VSI), which it is used as front-end between the DC-bus and the grid. The proposed converters are realized using the Silicon Carbide (SiC) devices in order to improve the efficiency. Furthermore, the control strategy to regulate the generator side and grid side currents has been implemented. The proposed system has been validated using the Hardware-In-the-Loop (HIL) test bench and 20 kW SiC power converters.

In recent years, the portable technology is receiving a great interest and significant improvement due to the progresses in electronic technology development and energy storage solutions. The decrease in power requirements for working energy systems, due to the increased efficiency and to the reduction in components size, opens the access to new solutions for power supplying. In particular, alternative backup systems for battery charging or replacement could be designed taking advantage of unconventional technologies. It is the case of small photovoltaic portable panels or fuel cells technology: in these solutions different sources are used to produce limited electrical powers required to keep devices on. In this paper, a thermoelectric solution for the power generation has been considered: the generator has been designed and assembled starting from a catalytic combustor. Catalytic combustion allows safe control of the processes, and the choice of a hydrocarbon fuel ensures the power availability and a fast recharge. The size of the system is set to fit a volume close to the one of AA batteries. The electrical power output obtained is close to 1 W with a cold side temperature below 40 °C. The limited values of these physical parameters allow obtaining a portable and safe device. The generator has been fully characterized in different ranges of fuel flow rates and the performances have been thoroughly analysed for processes optimization and efficiency improvement.