• Energy Research
• 2016-2025close
• 7. Clean energy close
• CA close
• BE close
• MA close

The Box–Jenkins model is a polynomial model that uses transfer functions to express relationships between input, output, and noise for a given system. In this article, we present a Box–Jenkins linear model for a lithium-ion battery cell for use in electric vehicles. The model parameter identifications are based on automotive drive-cycle measurements. The proposed model prediction performance is evaluated using the goodness-of-fit criteria and the mean squared error between the Box–Jenkins model and the measured battery cell output. A simulation confirmed that the proposed Box–Jenkins model could adequately capture the battery cell dynamics for different automotive drive cycles and reasonably predict the actual battery cell output. The goodness-of-fit value shows that the Box–Jenkins model matches the battery cell data by 86.85% in the identification phase, and 90.83% in the validation phase for the LA-92 driving cycle. This work demonstrates the potential of using a simple and linear model to predict the battery cell behavior based on a complex identification dataset that represents the actual use of the battery cell in an electric vehicle.

Abstract This paper uses research-quality, ground measurements of irradiance and temperature that are accurate to ±2% to estimate the electric energy yield of fixed solar modules for utility-scale solar power plants at 18 sites in Saudi Arabia. The calculation is performed for a range of tilt and azimuth angles and the orientation that gives the optimum annual energy yield is determined. A detailed analysis is presented for Riyadh including the impact of non-optimal tilt and azimuth angles on annual energy yield. It is also found that energy yield in March and October are higher than in April and September, due to milder operating temperatures of the modules. A similar optimization of tilt and azimuth is performed each month separately. Adjusting the orientation each month increases energy yield by 4.01% compared to the annual optimum, but requires considerable labour cost. Further analysis shows that an increase in energy yield of 3.63% can be obtained by adjusting the orientation at five selected times during the year, thus significantly reducing the labour requirement. The optimal orientation and corresponding energy yield for all 18 sites is combined with a site suitability analysis taking into account climate, topography and proximity to roads, transmission lines and protected areas. Six sites are selected as having high suitability and high energy yield: Albaha, Arar, Hail, Riyadh, Tabuk and Taif. For these cities the optimal tilt is only slightly higher than the latitude, however the optimum azimuth is from 20° to 53° west of south due to an asymmetrical daily irradiance profile.

Abstract The adoption rate and stringency of building energy standards in the U.S. have been increasing since the mid-1990s as a result of the Energy Policy Act mandate of 1992 (EPAct). Current evidence on the energy savings that accrue from commercial building energy standards is based on engineering simulations, which do not account for realized behaviour once a standard is actually adopted. This paper uses quasi-experimental variation in commercial building energy standard adoptions to estimate their effect on realized electricity consumption and cost-effectiveness. In states induced by EPAct to adopt an energy standard where all new nonresidential construction was erected under a commercial standard, electricity consumption per service worker is lower by about 12%, and total commercial electricity consumption is lower by 10%. Including early adopters and never-adopters to the analysis leads to a downward bias in the treatment effect. The realized electricity savings in the EPAct states represent three quarters of predicted simulated savings, and electricity saved in 2010 came at a cost of approximately 7.7 cents per kWh.

Abstract For 118 million residential housing units in the U.S., there is currently a gap between the potential energy savings that can be achieved through the use of existing energy efficiency technologies, and the actual level of energy savings realized, particularly for the 37% of housing units that are considered residential rental properties. Additional quantifiable benefits are needed beyond energy savings to help further motivate residential property owners to invest in energy efficiency upgrades. This research focuses on assessing the adoption of energy efficient upgrades in U.S. residential housing and the impact on rental prices. Ten U.S. cities are chosen for analysis; these cities vary in size across multiple climate zones, and represent a diverse set of housing market conditions. Data was collected for over 159,000 rental property listings, their characteristics, and their energy efficiency measures listed in rental housing postings across each city. Following an extensive data quality control process, over thirty different types energy efficient features were identified. The level of adoption was determined for each city, ranging from 5.3% to 21.6%. Efficient lighting and appliances were among the most common, with many features doubling as energy efficient and other desirable aesthetic or comfort improvements. Then using propensity score matching and conditional mean comparison methods, the relative impact on rent charged in each city was calculated, which ranged from a 6% to 14.1% increase in rent for properties with energy efficient features, demonstrating a positive economic impact of these features, particularly for property owners. This was further subdivided into five types of energy efficiency upgrade and three housing types. Single family homes generally demanded higher premiums with energy efficient features, however there was not a consistent pattern across the types of efficient upgrades. The results of this work demonstrate that investment in energy efficient technologies has quantifiable benefits for rental property owners in the U.S. beyond just energy savings. This methodology and results can also be used in other cities and by property owners, utility companies, or others, ultimately encouraging further investment and positive economic impact in residential energy efficiency and in turn improving energy and resource conservation in the building sector.

Abstract A new formulation for the evaporation, flashing, condensation processes taking place in the effects of thermal desalination systems which simulates the operation of both forward and parallel/cross configurations is coupled with an exergo-economic model based on the SPECO method. The thermo-economic model uses accurate properties for the seawater, brine, pure water and vapour and is solved with an equation solver which does not require the development of a specific solution algorithm as in most previous studies. This flexible model is used to analyze the influence of the number of effects N and the temperature difference ΔT e between effects on the technical and economic performance of multi-effect desalination systems with ejector vapour compression. In particular, it is shown that the performance calculated by an earlier black-box approach is not attainable by technically and economically realistic systems. It is also shown that for each feed configuration and a given number of effects there exists an optimum value of ΔT e which minimizes the cost of the produced potable water. This last result forms the basis of a procedure that combines black-box results with the optimum value of ΔT e and can be used to select the appropriate system for any specific application.

In response to the pressing need for transportation decarbonization, this paper examines the often overlooked domain of inland waterway transport and seeks to answer which alternative fuel or power source is the most promising for that sector. As the shipping industry significantly contributes to global carbon emissions, it has been shifting towards alternative fuels and decarbonization measures in the effort to reduce them, whereas the inland waterways, operating predominantly on diesel engines, have not achieved equivalent substantial progress. Employing a systematic literature review and regional analysis, this study identifies notable trends. LNG initially emerged as a favored alternative fuel, but recent studies emphasize a shift towards “greener” solutions like batteries and hydrogen. Europe and Asia lead in these developments. This investigation uncovers critical gaps in research and development, particularly in the Northern European countries that have extensive inland waterway networks. It also calls for future studies to explore the performance of vessels that have adopted LNG compared to other emerging alternatives and emphasizes the importance of considering the time lag between technology development and research publication.

Owing to their high luminous efficiency and tunable emission in both red light and far-red light regions, Mn4+ ion-activated phosphors have appealed significant interest in photoelectric and energy conversion devices such as white light emitting diode (W-LED), plant cultivation LED, and temperature thermometer. Up to now, Mn4+ has been widely introduced into the lattices of various inorganic hosts for brightly red-emitting phosphors. However, how to correlate the structure-activity relationship between host framework, luminescence property, and photoelectric device is urgently demanded. In this review, we thoroughly summarize the recent advances of Mn4+ doped phosphors. Meanwhile, several strategies like co-doping and defect passivation for improving Mn4+ emission are also discussed. Most importantly, the relationship between the protocols for tailoring the structures of Mn4+ doped phosphors, increased luminescence performance, and the targeted devices with efficient photoelectric and energy conversion efficiency is deeply correlated. Finally, the challenges and perspectives of Mn4+ doped phosphors for practical applications are anticipated. We cordially anticipate that this review can deliver a deep comprehension of not only Mn4+ luminescence mechanism but also the crystal structure tailoring strategy of phosphors, so as to spur innovative thoughts in designing advanced phosphors and deepening the applications.

Abstract In the present study, Loblolly pine biomass residue was converted to bio-oil in a two-step process, consisting of 1) fast pyrolysis in the presence of zeolite ZSM-5 as a catalyst to produce pyrolysis oil, 2) hydrogenation of pyrolysis oil using formic acid as the hydrogen source in presence of Ru/activated carbon catalyst. Pyrolysis oils were analyzed by 13C, 31P and HSQC-NMR and the results revealed that the zeolite-induced catalytic fast pyrolysis process led to effective demethoxylation, producing more catechol and p-hydroxy-phenyl hydroxyl groups in the bio-oils, resulting in a decrease in the methoxyl group content by about 85 % and rich aromatic structures in the pyrolysis oils. The properties of pyrolysis oil with and without zeolite were in the bio-oil range. Hydrogenated pyrolysis oil showed that 79 % of the aromatic protons are eliminated and 87 % of protons are aliphatic in nature, with no oxygen attached to the α-carbon.

The ‘4 per mille Soils for Food Security and Climate’ was launched at the COP21 with an aspiration to increase global soil organic matter stocks by 4 per 1000 (or 0.4 %) per year as a compensation for the global emissions of greenhouse gases by anthropogenic sources. This paper surveyed the soil organic carbon (SOC) stock estimates and sequestration potentials from 20 regions in the world (New Zealand, Chile, South Africa, Australia, Tanzania, Indonesia, Kenya, Nigeria, India, China Taiwan, South Korea, China Mainland, United States of America, France, Canada, Belgium, England & Wales, Ireland, Scotland, and Russia). We asked whether the 4 per mille initiative is feasible for the region. The outcomes highlight region specific efforts and scopes for soil carbon sequestration. Reported soil C sequestration rates globally show that under best management practices, 4 per mille or even higher sequestration rates can be accomplished. High C sequestration rates (up to 10 per mille) can be achieved for soils with low initial SOC stock (topsoil less than 30 t C ha− 1), and at the first twenty years after implementation of best management practices. In addition, areas which have reached equilibrium will not be able to further increase their sequestration. We found that most studies on SOC sequestration only consider topsoil (up to 0.3 m depth), as it is considered to be most affected by management techniques. The 4 per mille number was based on a blanket calculation of the whole global soil profile C stock, however the potential to increase SOC is mostly on managed agricultural lands. If we consider 4 per mille in the top 1m of global agricultural soils, SOC sequestration is between 2-3 Gt C year− 1, which effectively offset 20–35% of global anthropogenic greenhouse gas emissions. As a strategy for climate change mitigation, soil carbon sequestration buys time over the next ten to twenty years while other effective sequestration and low carbon technologies become viable. The challenge for cropping farmers is to find disruptive technologies that will further improve soil condition and deliver increased soil carbon. Progress in 4 per mille requires collaboration and communication between scientists, farmers, policy makers, and marketeers.