• Energy Research
• Restricted close
• Open Source close
• CA close
• NL close
• Applied Energy close

In this study we show that a chemical ferricyanide cathode can be replaced by a biological oxygen reducing cathode in a plant microbial fuel cell (PMFC) with a new record power output. A biocathode was successfully integrated in a PMFC and operated for 151 days. Plants growth continued and the power density increased reaching a maximum power output of 679 mW/m2 plant growth area (PGA) in a 10 min polarization. The two week record average power densities was 240 mW/m2 PGA. The new records were reached due to the high redox potential of oxygen reduction which was effectively catalyzed by microorganisms in the cathode. This resulted in a 127 mV higher cathode potential of the PMFC with a biocathode than a PMFC with a ferricyanide cathode. We also found that substrate availability in the anode likely limits the current generation. This work is crucial for PMFC application as it shows that PMFC can be a completely sustainable biotechnology with an improved power output.

Need for reduction of energy use in greenhouse production has increased. First objective was to develop and validate a dynamic air temperature model. Second objective was to minimize total energy input to the greenhouse, for pre-set temperature boundaries. Optimal control techniques were used to minimize total energy input (cooling and heating). Results confirm that air temperature is on the upper boundary when cooling is applied and on the lower boundary when heating is applied. This work is a first step toward optimal deployment of a large array of possible options for the grower to optimally satisfy heat or cooling.

Abstract Thermal energy storage systems for both heat and cold are necessary for many industrial processes. High energy density and high power capacity are desirable properties of the storage. The use of latent heat increases the energy density of the storage tank with high temperature control close to the melting point. Tube in PCM tank is a very promising system that provides high packing factor. This work presents an experimental study of a PCM tank for cold storage applications. Two different configurations and different flow rates of the heat transfer fluid were studied. The effectiveness of the PCM storage system was defined as that of a heat exchanger. The results showed that the heat exchange effectiveness of the system did not vary with time, decreased with increasing flow rate and increased with increasing heat transfer area. The effectiveness was experimentally determined to only be a function of the ratio m ˙ /A. This equation was found to be adequately be used to design a PCM storage system, and a case study is presented. It was shown that the tube in tank design together with a low temperature PCM is suitable as a thermal storage facility for cold storage.

Depleted hydrocarbon reservoirs and deep saline aquifers are key targets for geological storage of CO

Abstract Life Cycle Assessment (LCA) has been conducted for seven experimental cubicles located in Puigverd de Lleida (Spain). The objective of this experimental set-up is to test different constructive solutions in order to point out the most sustainable solution with lower energy demand during the operational phase. Therefore, different building, insulation and Phase Change Materials (PCMs) have been tested under controlled temperature conditions to examine the thermal performance of the whole system. Although some of these materials are able to reduce the energy demand and consequently the environmental impact during the operational phase, they still have high embodied energy that can cause high environmental impact during the manufacturing phase. Therefore the LCA study in this paper focuses on assessing the impact of the embodied energy needed during the manufacturing and disposal phase by highlighting and comparing the effect of using different building materials, insulating materials, and phase change materials.

Aquifer thermal energy storage (ATES) is a cost-effective technology that enables the reduction of energy use and CO2 emissions associated with the heating and cooling of buildings by storage and recovery of large quantities of thermal energy in the subsurface. Reducing the distance between wells in large-scale application of ATES increases the total amount of energy that can be provided by ATES in a given area. However, due to thermal interference the performance of individual systems can decrease. In this study a novel method is presented that can be used to (a) determine the impact of thermal interference on the economic and environmental performance of ATES and (b) optimize well distances in large-scale applications. The method is demonstrated using the hydrogeological conditions of Amsterdam, Netherlands. Results for this case study show that it is cost-effective to allow a limited amount of thermal interference, such that 30–40% more energy can be provided in a given area compared to the case in which all negative thermal interference is avoided. Sensitivity analysis indicates that optimal well distance is moderately insensitive to changes in hydrogeological and economic conditions. Maximum economic benefit compared to conventional heating and cooling systems on the other hand is sensitive, especially to changes in the gas price and storage temperatures.

Central solar heating plants with seasonal storage (CSHPSS) are among the most promising technologies to save energy in the industrial and residential-commercial building sectors. This work introduces a systematic approach to optimize these systems according to economic and environmental criteria. Our method, which combines the TRNSYS 17 simulation software with life cycle assessment and multi-objective optimization, identifies optimal CSHPSS designs for any climatic condition and heating demand profile considering economic and environmental criteria simultaneously. The capabilities of this approach are illustrated through its application to a case study of a CSHPSS located in Barcelona (Spain), which satisfies a heating demand for a neighborhood of 1120 dwellings. Numerical results show that the CSHPSS plant leads to significant environmental and economic improvements compared to the use of a conventional natural gas heating system. Our tool can guide engineers and architects in the transition towards a more sustainable residential sector.

Aquaculture has become an important sector of animal food production thanks to a fast and continuous growth over the last few decades. Both marine and fresh water fish can be reared in fish farms, and there are species that are mainly produced by aquaculture rather than capture. As most of the reared fish species are sensible to water temperature and its fluctuations, having the control of this parameter in fish farms becomes an important issue that has to be taken into account. In this paper, three different fish farms are studied by simulating the water temperature when a thermal energy storage (TES) system using phase change materials (PCMs) is implemented. The effect and the estimated amounts of PCM required in each particular case are also analyzed. The results show that appreciable effects can be obtained, especially when the TES unit is used in combination with auxiliary sources of energy, such as solar collectors.