• Energy Research
• engineering and technology close
• 7. Clean energy close
• 12. Responsible consumption close
• EU close
• PL close
• AT close

This paper evaluated the environmental effects of socially responsible investments (SRIs) in European countries and analyzed the differentiation between them in terms of SRIs and selected features in the environmental dimension. The first section of the paper discusses contemporary trends in Europe and in certain European countries, whilst the second compares SR environmental investments and environmental factors in selected European countries from a multidimensional perspective. The aim of the study was to identify and evaluate these trends as well as to find similarities and differences between European countries, and subsequently to indicate groups of countries with similar approaches to pro-ecological investments. In order to solve the problem, descriptive and multidimensional statistical methods were used, namely correspondence analysis (CA). Although the research results clearly revealed upward tendencies in the volume of SR environmental investments in the analyzed period, they nonetheless represent a relatively low share in the total number of socially responsible investments. The overall growth in SRIs in Europe may have resulted from the more intense activities of policymakers in some countries as a consequence of concluding agreements reached during the 21st Conference of the Parties (COP21) in 2015. The results of the study also revealed no significant correlations between SR environmental investments and environmental variables among the European countries analyzed; hence, there is no substantial evidence that investors’ assets contribute to the improvement of the environment.

This study focuses on formulating the most sustainable concrete by incorporating recycled concrete aggregates and other products retrieved from construction and demolition (C&D) activities. Both recycled coarse aggregates (RCA) and recycled fine aggregates (RFA) are firstly used to fully replace the natural coarse and fine aggregates in the concrete mix design. Later, the cement rich ultrafine particles, recycled glass powder and mineral fibres recovered from construction and demolition wastes (CDW) are further incorporated at a smaller rate either as cement substituent or as supplementary additives. Remarkable properties are noticed when the RCA (4–12 mm) and RFA (0.25–4 mm) are fully used to replace the natural aggregates in a new concrete mix. The addition of recycled cement rich ultrafines (RCU), Recycled glass ultrafines (RGU) and recycled mineral fibres (RMF) into recycled concrete improves the modulus of elasticity. The final concrete, which comprises more than 75% (wt.) of recycled components/materials, is believed to be the most sustainable and green concrete mix. Mechanical properties and durability of this concrete have been studied and found to be within acceptable limits, indicating the potential of recycled aggregates and other CDW components in shaping sustainable and circular construction practices. The authors wish to acknowledge the financial support from EU Horizon 2020 Project VEEP ‘‘Cost-Effective Recycling of C&DW in High Added Value Energy Efficient Prefabricated Concrete Compo-nents for Massive Retrofitting of our Built Environment” (No.723582).

IT technologies related to Industry 4.0 facilitate the implementation of the framework for sustainable manufacturing. At the same time, Industry 4.0 integrates IT processes and systems of production companies with IT solutions of cooperating companies that support a complete manufactured product life cycle. Thus, the implementation of sustainable manufacturing implies a rapid increase in interfaces between IT solutions of cooperating companies. This, in turn, raises concerns about security among manufacturing company executives. The lack of a recognized methodology supporting the decision-making process of choosing the right methods and means of cybersecurity is, in effect, a significant barrier to the development of sustainable manufacturing. As a result, the propagation of technologies in Industry 4.0 and the implementation of the sustainable manufacturing framework in companies are slowing down significantly. The main novelty of this article, addressing the above deficiencies, is the creation, using the combined DEMATEL and ANP (DANP) and PROMETHEE II methods, of a ranking of the proposed three groups of measures, seven dimensions and twenty criteria to be implemented in companies to ensure cybersecurity in Industry 4.0 and facilitate the implementation of the sustainable production principles. The contribution of Industry 4.0 components and the proposed cybersecurity scheme to achieve the Sustainable Development goals, reducing the carbon footprint of companies and introducing circular economy elements was also indicated. Using DANP and PROMETHEE II, it can be concluded that: (i) the major criterion of cybersecurity in companies is validation and maintaining electronic signatures and seals; (ii) the most crucial area of cybersecurity is network security; (iii) the most significant group of measures in this regard are technological measures.

The hydraulic balance of heating network is considered as a pre-condition for the implementation of low temperature district heating (LTDH). Its imbalance result into high energy consumption and heat-losses in the network. In this study, a novel hydraulic model is presented which investigates hydraulic imbalance in the LTDH network, using real weather and hourly monitored operational heating data from an existing boiler based building. Analysis of delta t in space-heating system shows that the delta t is maximum when the outside air temperature is lowest and it decreases with increase in outside air temperature. Furthermore, the hydraulic imbalance is analysed for four different control scenarios with the aim to find an optimum scenario with minimum pumping power, energy consumption and heat-losses in the LTDH network. Results show that the hydraulic imbalance is due to the absence of flow-limiters and balancing valves on the return pipe and thermostatic radiator valves (TRVs) alone are unable to maintain hydraulic balance in the space-heating system of buildings. Moreover, the control scenario with variable flow-rate and fixed supply water temperature from the sub-station is found to be optimum. Compared to the constant flow-rate scenario, the pumping power, energy consumption and heat-losses in the LTDH network are reduced by approximately 2%, 63% and 14%, respectively.

The successful electricity grid integration of solar energy into day-ahead markets requires at least hourly resolved 48 h forecasts. Technologies as photovoltaics and non-concentrating solar thermal technologies make use of global horizontal irradiance (GHI) forecasts, while all concentrating technologies both from the photovoltaic and the thermal sector require direct normal irradiances (DNI). The European Centre for Medium-Range Weather Forecasts (ECMWF) has recently changed towards providing direct as well as global irradiances. Additionally, the MACC (Monitoring Atmospheric Composition & Climate) near-real time services provide daily analysis and forecasts of aerosol properties in preparation of the upcoming European Copernicus programme. The operational ECMWF/IFS (Integrated Forecast System) forecast system will in the medium term profit from the Copernicus service aerosol forecasts. Therefore, within the MACC‑II project specific experiment runs were performed allowing for the assessment of the performance gain of these potential future capabilities. Also the potential impact of providing forecasts with hourly output resolution compared to three-hourly resolved forecasts is investigated. The inclusion of the new aerosol climatology in October 2003 improved both the GHI and DNI forecasts remarkably, while the change towards a new radiation scheme in 2007 only had minor and partly even unfavourable impacts on the performance indicators. For GHI, larger RMSE (root mean square error) values are found for broken/overcast conditions than for scattered cloud fields. For DNI, the findings are opposite with larger RMSE values for scattered clouds compared to overcast/broken cloud situations. The introduction of direct irradiances as an output parameter in the operational IFS version has not resulted in a general performance improvement with respect to biases and RMSE compared to the widely used Skartveit et al. (1998) global to direct irradiance conversion scheme. Cloudy situations and especially thin ice cloud cases are forecasted much better with respect to biases and RMSE, but large biases are introduced in clear sky cases. When applying the MACC aerosol scheme to include aerosol direct effects, an improvement especially in DNI biases is found for cloud free cases as expected. However, a performance decrease is found for water cloud cases. It is assumed that this is caused by the lack of an explicit modelling of cloud-aerosol interactions, while other meteorological forcings for cloud processes like the temperature field are modified by the aerosols.

Vehicles with hybrid drive systems, are increasingly more often being equipped with solutions that increase the drive systems efficiency. One of such solutions is to use an increased supply voltage for electric motors of such vehicles. The battery voltage is increased several times in the inverter system in order to increase the electrical power supplied to the electric motor. This article presents possible uses of such voltage amplification (called boost) in urban traffic conditions. The tests used the latest models of vehicles with hybrid drive systems equipped with the same drive units: Lexus NX 300h and Toyota RAV4 Hybrid. The study analyses the conditions of starting such a system and the characteristics of its operation. It has been shown that the amplification of the voltage powering the electrical machinery in both vehicles occurs at high torque values. The maximum voltage amplification–almost threefold (up to 650 V) allows a two-fold increase in the torque of the drive system.

Abstract In an effort to minimise electricity consumption and greenhouse gases emissions, the heating, ventilation and air-conditioning sector has focused its attention on developing alternative solutions to electrically-driven vapour-compression cooling. Liquid desiccant air-conditioning systems represent an energy-efficient and more environmentally friendly alternative technology for dehumidification and cooling, particularly in those cases with high latent loads to maintain indoor air quality and comfort conditions. This technology is considered particularly efficient in hot and humid climates. As a matter of fact, the choice of the desiccant solution influences the overall performance of the system. The current paper reviews the working principle of liquid desiccant systems, focusing on the thermodynamic properties of the desiccant solutions and describes an evaluation of the reference thermodynamic properties of different desiccant solutions to identify which thermodynamic, physical, transport property influences the liquid desiccant process and to what extent. The comparison of these thermodynamic properties for the commonly used desiccants is conducted to estimate which fluid could perform most favourably in the system. The economic factors and the effect of different applications and climatic conditions on the system performance are also described. The paper is intended to be the first step in the evaluation of alternative desiccant fluids able to overcome the problems related to the use of the common desiccant solutions, such as crystallization and corrosion to metals. Ionic liquids seem a promising alternative working fluid in liquid desiccant air-conditioning systems and their characteristics and cost are discussed.