• Energy Research
• Closed Access close
• 7. Clean energy close
• 13. Climate action close
• 1. No poverty close
• PL close
• CZ close

Vehicles with hybrid drive systems, are increasingly more often being equipped with solutions that increase the drive systems efficiency. One of such solutions is to use an increased supply voltage for electric motors of such vehicles. The battery voltage is increased several times in the inverter system in order to increase the electrical power supplied to the electric motor. This article presents possible uses of such voltage amplification (called boost) in urban traffic conditions. The tests used the latest models of vehicles with hybrid drive systems equipped with the same drive units: Lexus NX 300h and Toyota RAV4 Hybrid. The study analyses the conditions of starting such a system and the characteristics of its operation. It has been shown that the amplification of the voltage powering the electrical machinery in both vehicles occurs at high torque values. The maximum voltage amplification–almost threefold (up to 650 V) allows a two-fold increase in the torque of the drive system.

It is important to reduce the amount of municipal waste deposited in landfills, Czech Republic, therefore, puts more emphasis on the recovery of mixed municipal waste, which oblige and EU regulations. Production of solid alternative fuel that is suitable also due to less consumption of fossil fuels, is one of the uses of mixed municipal waste (Waste to Energy). A relatively high proportion of glass in mixed municipal waste is a major problem in the production of solid alternative fuel. The glass contained in the solid alternative fuel can be the cause of formation incrusts on heat transfer surfaces in combustion plants. For all examined types of glass, it was found that the melting temperature of the muffle furnace was 750 ° C. When using the method (ISO 540) for determining the temperature of softening , melting and flow showed no effect of the amount of glass in the ash, but the melting point was significantly higher (around 1,200 °C).

Abstract An alkaline earth boro-aluminosilicate glass (Eagle XG), a soda-lime glass, and a light-weight polyethylene-terephthalate (PET) foil, used as typical substrates for photovoltaics, were treated by an energetic proton beam (3 MeV, dose 106–107 Gy) corresponding to approx. 30 years of operation at low Earth orbit. Properties of the irradiated substrates were characterized by atomic force microscopy, optical absorption, optical diffuse reflectance, Raman spectroscopy, X-ray photoelectron spectroscopy, Fourier-transform infrared (FTIR) spectroscopy, and terahertz (THz) spectroscopy. Minimal changes of optical and morphological properties are detected on the bare Eagle XG glass, whereas the bare PET foil exhibits pronounced increase in optical absorption, generation of photoluminescence, as well as mechanical bending. On the other hand, the identical substrates coated with Indium-tin-oxide (ITO), which is a typical material for transparent electrodes in photovoltaics, exhibit significantly higher resistance to the modifications by protons while ITO structural and electronic properties remain unchanged. The experimental results are discussed considering a potential application of these materials for missions in space.

Abstract The supercritical power plant analyzed in this paper consists of the following elements: a steam turbine, a hard-coal-fired oxy-type pulverized fuel boiler, an air separation unit with a four-end-type high-temperature membrane and a carbon dioxide capture unit. The electrical power of the steam turbine is 600 MW, the live steam thermodynamic parameters are 650°C/30 MPa, and the reheated steam parameters are 670°C/6 MPa. First of all the net efficiency was calculated as functions of the oxygen recovery rate. The net efficiency was lower than the reference efficiency by 9–10.5 pp, and a series of actions were thus proposed to reduce the loss of net efficiency. A change in the boiler structure produced an increase in the boiler efficiency of 2.5–2.74 pp. The range of the optimal air compressor pressure ratio (19–23) due to the net efficiency was also determined. The integration of all installations with the steam turbine produced an increase in the gross electric power by up to 50.5 MW. This operation enabled the replacement of the steam regenerative heat exchangers with gas–water heat exchangers. As a result of these alterations, the net efficiency of the analyzed power plant was improved to 5.5 pp less than the reference efficiency.

Abstract Efficiency of the earth-to-air heat exchangers depends not only on their thermal performance but also on the total pressure losses that are the cost of harvesting a geothermal heat. In this paper the sensitivity analysis of the flow characteristics to the change of multi-pipe exchanger geometry is presented. Experimental investigation and CFD simulation results present total pressure losses in the considered exchangers and airflows in each branch-pipes. Considered geometrical structures varies in the number of parallel pipes, pipes length, main pipes diameters and supply type. The experimental investigations were conducted on the exchangers models in a scale 1:4. To investigate the real size exchangers, validated CFD flow performance model was used. A costless modification of heat exchanger supply-type from Z-type to U-type structure (change in air inlet location) is verified as a simple method of decreasing total pressure losses by 6–36% and improving airflow division uniformity by 11–80%. It is shown that main pipes diameter that are 1.4 times bigger than parallel pipes diameter can result in diminished total pressure losses by 56–73% and improved airflow division uniformity by 6–59%. The least significant effect on the flow characteristics has the branch-pipe length. Total pressure losses of long branch-pipes exchangers can be 15–32% higher than for short ones and the airflow division uniformity can be 8–35% higher. Results can be used for choosing the proper geometry of multi-pipe earth-to-air heat exchangers from the flow performance point of view. Presented flow characteristics can be used in detailed analysis and energy assessment of exchangers cooperating with the mechanical ventilation system in building.

Abstract The direct carbon fuel cells with solid oxide electrolyte (DC-SOFC) and anodes deposited by inject printing (EM/DCIJP) were studied. The cells were fed with carbon fuel obtained by the direct RF plasma splitting of methane. Since the (EM/DCIJP)M/DCIJP technology allows easy modification of electrode material, the effect of Cu addition to the Ni–YSZ anode was investigated. The significant improvement of the cell performance with the new anode was observed.

In this work we assess the pathways for environmental improvement by the coal utilization industry for power generation in Australia. In terms of resources, our findings show that coal is a long term resource of concern as coal reserves are likely to last for the next 500 years or more. However, our analysis indicates that evaporation losses of water in power generation will approach 1000 Gl (gigalitres) per year, equivalent to a consumption of half of the Australian residential population. As Australia is the second driest continent on earth, water consumption by power generators is a resource of immediate concern with regards to sustainability. We also show that coal will continue to play a major role in energy generation in Australia and, hence, there is a need to employ new technologies that can minimize environmental impacts. The major technologies to reduce impacts to air, water and soils are addressed. Of major interest, there is a major potential for developing sequestration processes in Australia, in particular by enhanced coal bed methane (ECBM) recovery at the Bowen Basin, South Sydney Basin and Gunnedah Basin. Having said that, CO2 capture technologies require further development to support any sequestration processes in order to comply with the Kyoto Protocol. Current power generation cycles are thermodynamic limited, with 35-40% efficiencies. To move to a high efficiency cycle, it is required to change technologies of which integrated gasification combined cycle plus fuel cell is the most promising, with efficiencies expected to reach 60-65%. However, risks of moving towards an unproven technology means that power generators are likely to continue to use pulverized fuel technologies, aiming at incremental efficiency improvements (business as usual). As a big picture pathway, power generators are likely to play an increasing role in regional development; in particular EcoParks and reclaiming saline water for treatment as pressures to access fresh water supplies will significantly increase.

Abstract The innovation of this research was a holistic approach to the problem of linking the biometric characteristics of six energy plants species and the distribution of moisture along the shoot‘ height and determination of linear models of particle sizes in relation to the moisture. The median biometric parameters values for growth phases I and II were as follows: shoot weight: 63 g and 65 g; stalk weight: 45.1 g and 43.8 g; plant length: 1273 mm and 2157 mm; shoot centre of gravity: 698 mm and 968 mm; slenderness ratio 147 and 215, respectively. For big bluestem and Spartina pectinata the largest values were for slenderness ratio and for phase II amounted to 403 and 410, respectively but most other parameters were the smallest values. Regarding the shoots’ growth, the greatest influence was on the stalks by increasing their lengths more than their diameters. The highest difference in the plant length between harvest terms was observed for Spartina pectinata which increased from 793 mm to 2257 mm (by 185%). The lengths of the Jerusalem artichoke, miscanthus and big bluestem plants also significantly increased: from 1345 mm to 2920 mm (117%), 1214 mm to 2065 mm (70%) and 1064 mm to 1779 mm (67%), respectively. Positive correlation coefficient values between parameters (shoot weight, leaf weight, stalk weight and plant length) indicate that to characterize of plant shoots the shoot mass and plant slenderness could be used. The Rosin-Rammler function fit the chopped plan material size distribution data with an R 2 = 0.909–0.991. All the biomass particle sizes belonged to the “very poorly sorted” category (2.00 mm ≤ σ ig ≤ 4.00 mm), and the particle size distributions were “fine skewed” (0.1 ≤ GS is ≤ 0.3) and “mesokurtic” (0.90 ≤ K gs ≤ 1.11). For grasses relation of particle sizes vs. moisture for phase II (August for Spartina and big bluestem or October for miscanthus) was inverted to phase I (June) with slope coefficients −0.11 and 0.09, respectively. For leaf plants direction of the relation was preserved, wherein for phase II (all plants harvested in October) the growth dynamic was lower than for phase I and slope coefficients of the lines were 0.17 and 0.04, respectively. Moisture content of leafy plants was high, and its distribution along the shoots’ heights was different than that for grasses. Varied values of particle size and weight of plant components, together with the change in moisture along the height of the plants, will impact the diversity of the dynamic loads of elements and working units of forage harvesters and can be useful to explain these results.

Abstract Currently, the first generation of silicon solar cells is dominating the photovoltaic market. Silicon cells are produced by various methods, which employ either crystalline or multi-crystalline substrates. However, both these manufacturing processes are expensive and potentially harmful to the environment and health. One example of this is that the surface is given its texture in a highly corrosive water solution of nitric and hydrofluoric acid. Additionally, both the diffusion and manufacturing of p-n junction and of metal contacts are associated with very high temperatures. This prompted us in our search for cheaper and more environmental friendly technologies. In this work, we discuss the possibility of producing components of photovoltaic cells by employing atomic layer deposition and hydrothermal technologies. This does not require the use of hazardous chemicals and high temperatures. The maximum efficiency of zinc oxide/silicon solar cells is 14% and 10% for textured and planar structures, respectively. A environmentally-friendly and simple procedure is thus being proposed, which, together with its relative efficiency, makes it an attractive alternative to the present procedure.