• Energy Research
• Open Access close
• other engineering and technologies close
• GB close
• FR close
• PL close

© 2020 Elsevier Ltd Free cooling of buildings uses the nocturnal outdoor air as a heat sink via a ventilation process. This could be performed by storing the night coolness for use during the daytime as appropriate. Due to the latent heat capacity, phase change material (PCM) could play anessential role in the effective operation of the free cooling systems by shifting the daytime peak load to the night. However, there is a scarceness on the technology application in hot climates. This paper presents results of a parametric investigation into the application of PCMs as thermal energy storage (TES) to provide sustainable cooling to buildings in hot arid climate by making use of the night-time free cooling. The proposed TES medium comprises an arrangement of metallic modules filled with RT28HC PCM. Numerous geometrical configurations and operational parameters have been assessed. A transient CFD simulation has been employed using ANSYS Fluent software. Validation of the numerical results with experimental data has shown a good agreement. The results have demonstrated that the temperature difference between the PCM and the air, at appropriate air flow rate would have a significant impact on the performance of the system. A free cooling system based on the proposed arrangement has the potential to meet around 42% of a typical building cooling load and has the ability to save up to 67% of building cooling energy load in summer season compared to conventional air-conditioning systems in hot arid climates.

The paper presents an experimental study on the formation process of burden surface texture on the blast furnace throat and its influence on the radial distribution of gas flow. The study was performed with the application of blast furnaces equipped with a bell-type charging device using radio-isotope means for the control of burden surface texture (profile) and burden surface level, i.e., gamma locators for burden surface texture. The study was carried out under the conditions of an operating blast furnace in an iron and steel plant using a unique GEOTAPS system for automated control of geometric and temperature parameters of burden material surface on the blast furnace throat. The influence of the surface texture on the gas flow distribution was also investigated. The possibility of a self-stabilization effect for burden surface texture and gas flow in an operating blast furnace under suitable conditions was experimentally proven. As a result of the experimental study performed, four ways of energy-saving technology implementation were determined for the control of blast furnace melting based on the data on the burden surface texture and previously unknown regularities of surface layer formation of burden material on the throat of an operating blast furnace with a bell-type charging device. The main idea of the paper is the development of automated control for the radial distribution of burden material and gas flow using actual or predicted surface texture parameters as important intermediate factors that both describe the process and have a significant simultaneous influence on it.

We present the architecture and design of the IANOS scheduling framework. The goal of the new Grid scheduling system is to provide a general job submission framework allowing optimal positioning and scheduling of HPCN applications. The scheduling algorithms used to calculate best-suited resources are based on an objective cost function that exploits information on the parameterization of applications and resources. This standard-based, interoperable scheduling framework comprises four general web services and three modules. The middleware is complemented with one client and one admin console. The implementation is based on proposed Grid and Web services standards (WSRF, WS-Agreement, JSDL, and GLUE). It is agnostic to a specific Grid middleware. The beta version of IANOS has been tested and integrated with UNICORE. The validation of IANOS is in progress by running different types of HPCN applications on a large-scale Grid testbed.

Biomass plays an important role in the world primary energy supplies, currently providing ∼14% of the world's primary energy needs and being the fourth largest contributor following coal, oil and natural gas. Over the past decade, domestic biomass heating has received more governmental and public supports than ever before in many developed countries, such as the UK. Although biomass combustion releases some combustion pollutants, biomass is renewable and produces little net CO 2 emissions to the atmosphere. Owing to the low sulphur and low nitrogen contents of many biomass materials, substituting biomass for fossil fuels, particularly coal, can reduce SO x and NO x emissions. This study investigated flue gas emissions, particularly carbon monoxide and nitrogen oxides, of a domestic biomass boiler under various operating conditions. The biomass boiler used in this study satisfies the current EU regulation (EN 303-05) on emissions of domestic biomass boilers. Emissions of the boiler had been measured not only under normal combustion conditions, but also under 'idle' combustion conditions when the boiler was not in but was ready for full operation. The experimental results are analysed and presented in this paper. Copyright The Author 2010. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oxfordjournals.org, Oxford University Press.

Abstract In this paper, a general mathematical model for the dynamic simulation of a single-effect LiBr/water absorption chiller is presented. The model is based on mass and energy balances applied to the internal components of the machine, and it accounts for the non-steady behaviour due to thermal and mass storage in the components. The validation of the mathematical model is performed through experimental data collected on a commercial small-capacity water-cooled unit. Due to the peculiar technology adopted in the real chiller, a special effort was made to identify the appropriate values of the main physical parameters. The validation of the model is based on the values of the water temperature at the outlet of the machine, as no measurement inside the machine was possible; anyway, a consistency analysis applied to the internal parameters is also presented. The agreement between experimental and simulated results is very good, both on a daily and on a seasonal basis.

Abstract A biomass oil/diesel blend was prepared using an emulsion method and combusted in a diesel engine. An injector was then removed and the morphology, composition, and structure of the carbonaceous deposits on the pintle-type nozzle were characterized using a combination of HRTEM, SEM/EDAX, Raman and XRD. Results showed that the carbon deposition of the emulsified fuel with high crystallinity was greater than that of diesel. The agglomerated particulate diameters of the deposited carbon from diesel and emulsified fuel were approximately 10–30 μm and 50 μm, respectively. The carbon deposition mechanism from the emulsified fuel was attributed to the high oxygen content of the groups leading to increased polymerization and subsequent condensation on the nozzle surfaces that was then carbonised.

Sustainability of agro-food supply chains has recently become the subject of greater interest from consumers, firms, governmental organizations and academia as the environment continues to deteriorate. One of the most critical factors influencing the sustainability of an agro-food supply chain is its network design. A particularly challenging aspect in this context is the broad range of influencing indicators associated with the Triple Bottom Line (TBL) of sustainability that need to be considered. However, many of these indicators could not be fully integrated or measured by single-step optimization problems. This paper presents a critical literature review of operational research methods for the design of sustainable supply chains. A novel two-stage hybrid solution methodology is proposed. In the first stage, a partner selection is performed using a hybrid multi criteria decision making based on Analytic Hierarchy Process (AHP) method and the Ordered Weighted Averaging (OWA) aggregation method. The result obtained in the first stage is used in the second stage to develop a multi-objective mathematical model to optimize the design of the supply chain network. This approach allows the simultaneous consideration of all three dimensions of sustainability including carbon footprint, water footprint, number of jobs created and the total cost of the supply chain design. The proposed approach generates a Pareto frontier to aid users in making decisions. Numerical experiments are completed utilizing data from an agro-food company to demonstrate the efficiency and effectiveness of the proposed solution methodology. The analyzes of the numerical results provide important organizational, practical and policy insights on (1) the impact of financial and environmental sustainability on supply chain network design (2) the tradeoff analysis between environmental emission, water footprint, societal implications and associated cost for making informed decision on supply chain investment.