• Energy Research
• RU close
• UA close
• University of Technology close

Abstract An ideal tracker which follows the sun both north-south and east-west is designed and constructed. It is suitable for mounting a linear concentrator, focusing parabolic concentrator or photovoltaic array of aperture area 2 m2. The apparatus is built with two axes equational mount and controlled by a microprocessor system. The tracking is carried out by utilizing the astronomical coordinates of the sun. As such the present system gives improved tracking capability over the conventional sensor controlled tracker systems. The performance of the tracking system was studied with photovoltaic array mounted on it and tracking error of less than one degree was achieved. This tracking error can be reduced further by proper software.

This paper reports on laboratory studies into the ac impedance spectra of nickel–metal hydride and nickel–cadmium batteries, aiming at finding out possible correlation between electrical parameters, extracted directly from the high frequency region, and the battery state-of-charge (SoC). Impedance diagrams were recorded immediately after interrupting the dc charge, or discharge, current. The study revealed that the series resonance frequency, at which the dynamic cell behavior switches from an inductive character (Z″>0) to a capacitive one (Z″<0), varied monotonously as a function of state-of-charge. This behavior was reproducible after intermittent charge and discharge. Half-cell measurements were also conducted to associate the cell impedance with either processes occurring at the positive or negative plates.

The mixing process of hot primary zone gases with secondary air must be rapid and intense for an advanced low NOX gas turbine based on a rich-burn/quick-mix/lean-burn (RQL) combustor. The injection of multiple jets normal into a confined crossflow is a key technology for this combustion concept. Therefore, an experimental investigation of a nonreacting mixing process of jets in a crossflow was conducted. The jets were injected through one stage of opposed rows of circular orifices into a slightly heated crossflow within a rectangular duct with no annular bypass. All geometries were tested with in-line and staggered arrangements of the centerlines of the opposed jets. Using the analogy of heat and mass transfer the temperature distribution was measured, and from that the mixing rate was determined for parametric variation of flow and geometric conditions. In accordance with the application to RQL combustion, emphasis was put on high momentum-flux ratios with high mass flow addition. The mixing process was found to be minimally affected by mainstream Reynolds number and mainstream turbulence, but significantly influenced by the addition of swirl to the mainstream. Correlations based on the experimental data were developed describing best mixing depending as a function of geometric conditions (duct height to hole diameter ratio, relative spacing of adjacent jets) and jet to crossflow momentum-flux ratio.

Both electrical and thermal efficiencies combine in determining and evaluating the performance of a PV/T collector. In this study, two PV/T systems consisting of poly and monocrystalline PV panels were used, which are connected from the bottom by a heat exchanger consisting of a spiral tube through which a nanofluid circulates. In this study, a base fluid, water, and ethylene glycol were used, and iron oxide nanoparticles (nano-Fe2O3) were used as an additive. The mixing was carried out according to the highest specifications adopted by the researchers, and the thermophysical properties of the fluid were carefully examined. The prepared nanofluid properties showed a limited effect of the nanoparticles on the density and viscosity of the resulting fluid. As for the thermal conductivity, it increased by increasing the mass fraction added to reach 140% for the case of adding 2% of nano-Fe2O3. The results of the zeta voltage test showed that the supplied suspensions had high stability. When a mass fraction of 0.5% nano-Fe2O3 was added the zeta potential was 68 mV, while for the case of 2%, it reached 49 mV. Performance tests showed a significant increase in the efficiencies with increased mass flow rate. It was found when analyzing the performance of the two systems for nanofluid flow rates from 0.08 to 0.17 kg/s that there are slight differences between the monocrystalline, and polycrystalline systems operating in the spiral type of exchanger. As for the case of using monocrystalline PV the electrical, thermal, and total PV/T efficiencies with 2% added Fe2O3 ranged between 10% to 13.3%, 43–59%, and 59 to 72%, respectively, compared to a standalone PV system. In the case of using polycrystalline PV, the electrical, thermal, and total PV/T efficiencies ranged from 11% to 13.75%, 40.3% to 63%, and 55.5% to 77.65%, respectively, compared to the standalone PV system. It was found that the PV/T electrical exergy was between 45, and 64 W with thermal exergy ranged from 40 to 166 W, and total exergy from 85 to 280 W, in the case of using a monocrystalline panel. In the case of using polycrystalline, the PV/T electrical, thermal, and total exergy were between 45 and 66 W, 42–172 W, and 85–238 W, respectively. The results showed that both types of PV panels can be used in the harsh weather conditions of the city of Baghdad with acceptable, and efficient productivity.

AbstractNowadays, researchers are focusing on the methods of using recycled industrial/agricultural wastes as raw materials, which are not only economically but also environmentally useful. In the recent years, many scholars have conducted research on the rational use of rice husks (RHs) and found that RHs are rich in inorganic/organic components and used in combination with the certain building materials to produce new green composite building materials. This paper studies the method of using RH processed products and the sodium silicate solution (liquid glass) made from RH ash to produce cheap wood substitute composite materials, which can be improved the insulation performance of the wall greatly. Obtained results are determined by comparing with the properties of standard polymer composite materials such as particleboards, chipboards, and medium‐density fiberboards (MDF). The significance of the work is pointing out by solving the problem of recycling large‐tonnage agricultural waste and reproduce products with the consumer's value.

Abstract This study presents and evaluates the feasibility of a novel hybridization of modified Kalina cycle, reverse osmosis desalination, and low-temperature water electrolysis utilizing geothermal energy to yield power, distilled water, and hydrogen, respectively. The scientific impact of the current work has been improved considering the features of Sabalan flash-binary geothermal wells in Iran as a real model through a case study. In addition to designing a novel setup, the smart use of multi-heat recovery technique, modifying the base cycle, and utilizing a part of generated distilled water to produce hydrogen by the electrolyzer are the other structural originalities, distinguishing the current work from the previous studies. The suggested system is scrutinized via a parametric study and optimized based on a genetic algorithm. The parametric study demonstrated that the highest sensitivity of varying the performance criteria of the whole system is attributed to the change in flash tank pressure. Moreover, the multi-objective optimization led to achieving the exergy efficiency and trigeneration gain output ratio as 51.3% and 1.7 for the system, respectively. Furthermore, the system was able to produce 4795 kW of power, 5.3 kg/h of hydrogen, and 19.9 kg/s of distilled water.

This study examined the potential use of macroalgae epiphytic on mangrove aerial roots as indicators of estuarine contamination. The distribution and abundance of macroalgae was investigated in four estuaries in the vicinity of Sydney, Australia, and compared to water and sediment metal concentrations, nutrient concentrations and physicochemical parameters over four seasonal surveys. Macroalgal diversity and distribution appeared to be highly influenced by the ambient contaminant concentrations, while biomass appeared to be linked with nutrient concentrations. The distribution of the Rhodophyta species, Catenella nipae Zanardini significantly decreased as metal concentrations increased among the estuaries during all seasonal surveys. This species showed strong potential for use as a bioindicator of estuarine contamination.

Closed-loop supply chain networks are gaining research popularity due to environmental, economic and social concerns. Such networks are primarily designed to overcome carbon footprints and to retrieve end of life products from customers. This study considers a multi echelon closed-loop supply chain in the presence of machine disruption. A multi-objective model is presented to optimize the total cost, the total time and emissions in a closed-loop supply chain network. The aim is to analyze the trade-off between the objectives of cost, time, and emissions and how these decisions are impacted by the selection of different available machines. A number of solution approaches are tested on a case study from the tire industry. The results suggest the improved performance of the hybrid heuristic and the importance of controlling disruption in a closed-loop supply chain network. Furthermore, there is a trade-off between the different objective functions which can help the decision maker to choose a particular solution according to the preference of an organization. Finally, conclusion and future research avenues are provided.

Turbulent spots were generated artificially to simulate natural spots in the transitional boundary layer. The spots at the final stage under zero and adverse pressure gradients were measured using conventional hotwire anemometry technique. Ensemble averages of the velocity traces were calculated and velocity profiles through the spots and the surrounding region were plotted. The spots are represented by the ensemble average of the velocity perturbations. The integral boundary layer properties are derived and compared through the spots. The effect of the pressure gradient on the turbulent spots is analysed with the structure of the spots and the ‘calmed region’ following the spots.