• Energy Research
• 7. Clean energy close
• 11. Sustainability close
• 8. Economic growth close
• CN close
• AU close
• UA close

Experimental investigation into the effects of different pilot amounts of dimethyl ether (DME) on the performance and emission of a single-cylinder directinjection DME engine is conducted. The results show that a DME engine can operate at a wider range of speeds and loads at quasi-homogenous charge compression ignition (QHCCI) mode. The brake thermal efficiency increases while the exhaust temperature decreases. NOx emission decreases by about 30%–50% although there is a slight increase in HC and CO emissions. NOx, HC and CO emissions increase with an increase in the amount of DME pilot. QHCCI is a good way to increase thermal efficiency and decrease NOx emission.

Abstract Predicting and optimizing radiative thermal properties have been acknowledged as an efficient way to improve thermal insulation performance of fibrous materials with high porosity. Based on experimental investigation of infrared spectral of ultrafine fibrous insulations with diameters of 520–650 nm, a method of calculating radiative thermal properties was presented by combining Rosseland equation, Mie scattering theory, Beer’s law and Subtractive Kramers–Kronig (SKK) relation. To ensure the calculation correct the uniqueness analysis was performed for Poly(vinylidene fluoride) (PVDF) fibers, which indicated the valid fiber diameter was less than 1.06 μm. The calculated thermal radiative conductivities by using the method agreed well with the measured data. The effect of fiber diameter on the thermal properties of the fibrous insulations was also investigated to minimize the radiative thermal conductivity. The results indicated that the minimized radiative thermal conductivities by regulating fiber diameters could be approximately 25% smaller than those for experimental fiber diameters. The method of predicting and minimizing radiative thermal conductivities of fibrous insulations demonstrated in this paper could be of great advantage to thermal engineering applications aiming to reducing heat loss and saving energy.

Reactive power consumption of the modern power system is a very important problem that to solve well. Due to the line commutated current source converter-based (LCC) HVDC system is a multivariable and strong coupling nonlinear system, it is difficult to model reactive power consumption of receiving end of LCC-HVDC by traditional analysis method. This paper proposes the reactive power consumption model of receiving end of LCC-HVDC on account of the radial basis function (RBF) neural network. The model with the turn-off angle for input, with reactive power loss on the inverter side of LCC-HVDC for output, using 500kV, 1000MW LCC-HVDC system PSCAD simulation test data training RBF neural network and testing network generalization ability. The results indicate that the reactive power loss model on account of the RBF neural network has much faster convergence speed and higher convergence precision.

Abstract Transient thermal behaviors of ultra-supercritical steam turbine control valves during the cold start warm-up process of steam turbine systems were comprehensively studied using conjugate heat transfer (CHT) simulation. The geometrical configurations and boundary conditions used in simulation were identical to the field setup in a thermal power plant. The simulated temperature variations were first validated using measurements by the flush-mounted thermocouples inside the solid valve bodies. The CHT simulation implementing the shear stress transport (SST) turbulence model demonstrated good agreement with the field data, and the overall numerical errors were below 10%; however, the numerical errors of the simulation, which used empirical heat transfer coefficients at the fluid–solid interfaces, reached 40%. The determined temperature differences between the cold valve bodies with the hot steam flow decreased significantly. Specifically, the temperature differences along the inner wall surfaces of the valve bodies decreased to less than 50 °C. Further investigation of the transient heat flux distributions and Nusselt number distributions confirmed that the unsteady flow behaviors, such as the alternating oscillations of the annular wall-attached jet, the central reverse flow and the intermediate shear layer instabilities, enhanced the fluid–solid heat convection process and thus contributed to the warming up of the solid valve bodies.

Flexible butyl interconnection segments are synthetically incorporated into an electronically conductive poly(pyrene methacrylate) homopolymer and its copolymer. The insertion of butyl segment makes the pyrene polymer more flexible, and can better accommodate deformation. This new class of flexible and conductive polymers can be used as a polymer binder and adhesive to facilitate the electrochemical performance of a silicon/graphene composite anode material for lithium ion battery application. They act like a “spring” to maintain the electrode mechanical and electrical integrity. High mass loading and high areal capacity, which are critical design requirements of high energy batteries, have been achieved in the electrodes composed of the novel binders and silicon/graphene composite material. A remarkable area capacity of over 5 mAh/cm2 and volumetric capacity of over 1700 Ah/L have been reached at a high current rate of 333 mA/g.

AbstractTo estimate the life cycle cost of thermal power equipments in engineering, this paper established a comprehensive evaluation model of life cycle cost with the life cycle breakdown and cost breakdown structure. Based on the model, this paper defined the cost elements of the thermal power equipment, analyzed influences of the thermal power equipment. Finally, the model is applied to an instance to estimate various cost categories in each life phase, which were summed up to the life cycle cost of the thermal power equipment.

A template‐agent can affect defect formation as well as influence interface properties, due to the rapid growth of perovskite film from the solution. Herein, diethylammonium iodide (DAI) is used as an effective template‐agent to control the perovskite crystallization during preparation. It is found that a very small amount of DAI in chlorobenzene (CB) can slow down the perovskite growth of the CH3NH3PbI3 (MAPbI3) film with more large grain size and compacted crystal‐grains resulting in the lesser grain boundaries (GBs) in favor of carrier transport in perovskite solar cells (PSCs). Moreover, some redundant PbI2 can be digested to form DA2PbI4. One part of DA2PbI4 can form the sub‐grains with the composition of (DA2PbI4)0.2(PbI2)0.8 to passivate the GB defects, and other part can cover the surface to passivate the surface defects in large MAPbI3 grains. Using an optimized DAI concentration of 0.5 mg mL−1 in CB solution, the corrsponding MAPbI3 PSC achieves an increased power conversion efficiency of 20.31% with suppressed current–voltage hysteresis. This DAI passivation strategy provides a simple approach to effectively assist the grain‐growth for improved device performance.

The rapid development of advanced metering infrastructure provides a new data source—building electrical load profiles with high temporal resolution. Electric load profile characterization can generate useful information to enhance building energy modeling and provide metrics to represent patterns and variability of load profiles. Such characterizations can be used to identify changes to building electricity demand due to operations or faulty equipment and controls. In this study, we proposed a two-path approach to analyze high temporal resolution building electrical load profiles: (1) time-domain analysis and (2) frequency-domain analysis. The commonly adopted time-domain analysis can extract and quantify the distribution of key parameters characterizing load shape such as peak-base load ratio and morning rise time, while a frequency-domain analysis can identify major periodic fluctuations and quantify load variability. We implemented and evaluated both paths using whole-year 15-minute interval smart meter data of 188 commercial office building in Northern California. The results from these two paths are consistent with each other and complementary to represent full dynamics of load profiles. The time- and frequency-domain analyses can be used to enhance building energy modeling by: (1) providing more realistic assumptions about building operation schedules, and (2) validating the simulated electric load profiles using the developed variability metrics against the real building load data.