• Energy Research
• Closed Access close
• Embargo close
• FR close
• UA close

The fast decay in PEM fuel cells of a highly active, high performance, but unstable Fe/N/C catalyst like our NC_Ar + NH3 follows a chemical, not an electrochemical, demetallation mechanism for its ORR active FeN4 sites in the catalyst micropores.

Abstract Theoretical analysis of the interaction between concentrated solar radiation and a honeycomb matrix or a bed of particles cooled by a gas is presented. The computation and the experimental results show evidence of overheating of the solid near the irradiated surface. To prevent the upper surface from this phenomenon and to reduce the radiative heat losses, we propose to use selective semi-transparent porous absorbers. The first results about coatings on silica are presented.

Resume Les resultats de la simulation d'un cycle a absorption fonctionnant en refrigeration a trois niveaux de pression font apparaitre un gain appreciable des performances par rapport a un cycle travaillant a deux niveaux de pression. Le n-butane (R600) est propose comme refrigerant et la dimethyl formamide (DMF) comme solvant. L'influence d'un certain nombre de parametres a ete etudiee et est presentee; ainsi, il a pu etre montre que le coefficient de performance peut atteindre des valeurs interessantes pour de faibles valeurs de la temperature de regeneration, redant ainsi possible l'utilisation de rejets thermiques ou bien de capteurs solaires peu sophistiques.

Abstract This paper gives an experimental investigation of the effect of climatic conditions on the performance and degradation of crystalline silicon photovoltaic modules under Saharan environment in Adrar region in the south of Algeria. The first part of this study is focused on the analysis and assessment of UDTS 50 PV modules degradation after a long term outdoor exposure to these conditions (more than 12 years). The visual inspection of 62 PV modules has allowed to observe and determine the degradation modes such as, EVA discoloration, delamination, busbar corrosion, cracking of solar cell, glass breakage, AR coating and solder bond. The degradation evaluation of three modules with different defects was also performed, using (I-V/P-V) characteristics and the degradation rates of the parameters (Pmax, Imp, Vmp, Isc, Voc, FF) at Standard test conditions (STC) in order to compare with the nominal data delivered by the manufacturer of photovoltaic panels. Finally, the combination of the partial shading effect and the presence of EVA browning defect was examined to assess the changes in I-V and P-V curves caused by the drop in electrical parameters.

AbstractCellulose and lignin nanoparticles are high‐value‐added products obtained from lignocellulosic biomasses through several steps of cellulose purification and lignin extraction. These steps drastically reduce the potential feedstock revenue when carried out as stand‐alone methodologies. To increase biomass yields, we describe here a strategy to design a biorefinery focused on producing cellulose and lignin nanoparticles as main products, but also aim to recover and benefit from other biomass components using only water‐based processes. Sequential pressurized liquid extractions and diluted acid and alkaline treatments were carried out to fractionate elephant grass biomass, yielding (for every 100 g of biomass): 30 g of cellulose pulp (converted to 9 g of cellulose nanocrystals and 9 g of cellulose nanofibers); 10 g of lignin (used to produce 8.5 g of stable colloidal lignin nanoparticles by probe‐sonication in water); 7.5 g of extractives (e.g. sterols and phenolics) and 23 g of xylose (converted to 4.1 g of furfural). Alternatively, to allow for the flexible use of the cellulose fraction in the proposed biorefinery, 22 g of glucose could be produced by enzymatic hydrolysis. The results demonstrate that water‐based processes are suitable for a holistic use of biomass, providing a comprehensive set of high‐value‐added co‐products that are renewable and cost‐effective chemical, cosmetic, food, polymer and pharmaceutical solutions.

Abstract This work presents a numerical study on the performance of a stand-alone adsorption cooling system based on the silica gel/water couple driven by hybrid photovoltaic/thermal (PVT) collectors. This system is intended for the conservation of perishable agricultural products which require air-conditioned premises to preserve them. The weather conditions are those of North Africa (Algiers). Considering the above, this paper aims at analyzing the PVT-Adsorption system with energy storage to guarantee a stabilized production and increase the solar coverage. trnsys was used to simulate the system taking into account hourly series of irradiation and ambient temperature covering one year. The performance study reveals that the DualSun PVT hybrid collectors used provide optimal annual production and that the adsorption cooling system offers more reliable production during summer. The temperature difference between the inside and outside of the cooled enclosure balances supply and demand. The loss analysis of the storage device indicates that losses depend, on the one hand, on the interior/exterior temperature difference of the storage tank with more significant values during the summer season. On the other hand, the losses also depend on the volume of the storage tank which was optimized in order to limit the heat exchange with the surroundings.

Use of a pilot-scale fixed-film bioreactor was investigated for remediation of bromate contamination within groundwater. Bromate reduction with stoichiometric production of bromide was observed, providing supporting evidence for complete reduction of bromate with no production of stable intermediates. Reduction of 87-90% bromate from an influent concentration of 1.1 mg L(-1) was observed with retention times of 40-80 h. Lower retention times led to decreases in bromate reduction capability, with 11.5% removal at a 10 h retention time. Nitrate reduction of 76-99% from a 30.7 mg L(-1) as NO(3)(-) influent was observed at retention times of 10-80 h, although an increase in nitrite production to 2.7 mg L(-1) occurred with a 10 h retention time. Backwashing was not required, with the large plastic packing media able to accommodate biomass accumulation without decreases in operational efficiency. This study has provided proof of concept and demonstrated the potential of biological bromate reduction by fixed-film processes for remediation of a bromate contaminated groundwater source.

Biodiesel is a fuel generally consisting of a mixture of fatty acid methyl esters (FAMEs) which is used in alternative or in combination with petroleum diesel for its environmental benefits. Biodiesel is conveniently manufactured from vegetable oils by transesterification of triglycerides with methanol. However, the process brings about the concurrent formation of glycerol, which may become an oversupplied chemical if biodiesel production keeps growing. A novel biodiesel-like material (abbreviated as DMC-BioD) was developed by reacting soybean oil with dimethyl carbonate (DMC), which avoided the co-production of glycerol. The main difference between DMC-BioD and biodiesel produced from vegetable oil and methanol (MeOH-biodiesel) was the presence of fatty acid glycerol carbonate monoesters (FAGCs) in addition to FAMEs. In the following study, details regarding synthesis and composition of DMC-BioD are provided along with physical properties relevant for its use as a fuel. In addition, the production of potential pyrogenic contaminants was investigated by analytical pyrolysis and compared with those from MeOH-biodiesel, and the model compounds tristearin, triolein, trilinolein and oleic acid glycerol carbonate ester (OAGC). The presence of FAGCs influenced both fuel and flow properties, while the distribution of main pyrogenic compounds, including polycyclic aromatic hydrocarbons (PAHs), was little affected. Benefits and drawbacks of DMC as a candidate transmethylating reagent for producing biofuel from renewable resources and alternative co-products (glycerol carbonate and glycerol dicarbonate) are discussed.

The solar energy produced by Scheffler parabola (10 m2) is not fully exploited by the solar distillation system of aromatic and medicinal plants. In this work, the optical losses in the primary and secondary reflectors, and the thermal losses at each part of this system (solar still, steam line, condenser) were determined. A thermal energetic and exergetic analysis were also performed for a solar distillation system of rosemary leaves. For average intensity radiation of 849.1W/m2 and 6 Kg of rosemary leaves during 4 h of distillation, exergy and optical efficiencies of the system achieved up to 26.62% and 50.97%, respectively. The thermal efficiency of the solar still, steam line, and condenser is about 94.80%, 94.30%, and 87.76%, respectively. The essential oil yield per unit of consumed energy and the total efficiency of the solar distillation system, taking into account the heat losses in the solar still, steam line, and condenser, as well as the optical losses in the two reflectors, is 6.18 mL/ kWh and 40.00%, respectively. The efficiency can be as high as 42.42 % if the steam line is insulated. Moreover, the comparison between the solar steam distillation and conventional steam distillation shows that solar distillation is much more efficient since it gives better results and especially it avoids the emission of 12.10 kg of CO2 during extraction.