• Energy Research
• natural sciences close
• UA close
• GB close
• Russian close

This research aim is to develop a method for modeling the conditions for the critical hydraulic impacts emergence on thermal and nuclear power plants’ pipeline systems pressure pumps departing from the general provisions of the heat and hydrodynamic instability theory. On the developed method basis, the conditions giving rise to the reliability-critical hydraulic impacts emergence on pumps for the thermal and nuclear power plants’ typical pipeline system have been determined. With the flow characteristic minimum allowable (critical) sensitivity, the flow velocity fluctuations amplitude reaches critical values at which the pumps working elements’ failure occurs. The critical hydraulic impacts emergence corresponds to the transition of the vibrational heat-hydrodynamic instability into an aperiodic one. As research revealed, a highly promising approach as to the preventing the critical hydraulic impacts related to the foreground use of pumps having the most sensitive consumption (at supply network) performance (while other technical characteristics corresponding to that parameter). The research novelty refers to the suggested method elaborated by the authors’ team, which, in contrast to traditional approaches, is efficient in determining the pump hydraulic impact occurrence conditions when the vibrational heat-hydrodynamic instability transition to the aperiodic instability.

A significant number of domestic and industrial boilers are in operation in Ukraine. Nitrogen oxides are the most dangerous among all combustion products that pollute the atmosphere, therefore, one should take some measures for decreasing the formation of nitrogen oxides during combustion. The studies were carried out at the boilers of low power (100 kW) with a tubular radiator and an open end. The studies in the furnaces of industrial steam boilers having a tubular radiator with a closed end have not been done. The numerical study results of the gaseous fuel combustion processes in the furnace of a DE-10/14 steam water-tube boiler are presented. The fuel-air mixture is formed by premixing the 15% part of the air with a primary burner twist factor n=2.4 and a secondary burner twist factor n=1.6, and an air excess factor αв=10. As a result of the studies, the temperature and velocity distributions of gases in the combustion chamber, the density of heat flows on the screen tubular surfaces, and the concentrations of the combustion components were determined. Flue gas recirculation in the volume of 80-100% is provided, and the reversible movement of combustion products towards the combustion front provides a reduction in the concentration of nitrogen oxides up to 123-125 mg/m3 at the furnace outlet. Disadvantages are the following: the formation of stagnant zones near the end of the secondary radiator. The optimum diameter of the tubular radiator equals to two burners diameters and tubular radiator is located at a distance of one meter from the burner cutoff.

The work is d to improving methods for calculating the cooling system of a microturbine with a rotor on air bearings. When designing gas turbines, it is important to integrate gas-dynamic calculations with thermal finite-element calculations. In practice, the conjugation of temperature fields in solids and liquids, as well as the transfer of thermal loads between the media are carried out using several approaches: direct, non-conjugate and sequential coupled. Numerical simulation of the coupled heat transfer in a cavity formed by the gap between the rotor and stator is carried out. To calculate the flow characteristics of a viscous compressible fluid and heat transfer. The degree of influence on the results of the type of turbulence model used, the influence of taking into account the conjugate heat transfer, is studied. The effect of the mass flow rate of the cooler on the flow structure and the cooling efficiency of the walls of the rotor and stator is investigated. A comparison is made with experimental data. Numerical experiments have shown that in typical cases the flow in the cavity is turbulent. The cooling efficiency has a limit on the flow rate of the cooler. The temperature distribution along the length of the rotor has a noticeable minimum in the region of the middle of the length of the rotor. The significance of the obtained results lies in the fact that the choice of the turbulence model weakly affects the calculation results and taking into account the conjugate nature of heat transfer is necessary.

The results of computer simulation of the processes of incineration of low-grade solid fuelpulverized peat with a moisture content of 40%, an ash content of 6% are given. It has been determined the fields of distribution of temperature, velocity of gases and particles in the volume and at the outlet from the furnace. The three-dimensional temperature distribution in the combustion chamber indicates high-temperature combustion of peat particles at temperatures above 1700°C with liquid ash removal in the lower part of the furnace. It has been determined that when the furnace is cooled, it is not ensured combustion of the fuel completely. The value of the swirling flow rate at the outlet from the furnace (up to 370 m/s) ensures the efficiency of separation of fuel particles, reducing heat losses from mechanical underburning. It is determined that the concentration of oxygen is close to zero over the entire height of the furnace, at an outlet from the furnace the oxygen concentration is 5...6%, since oxygen is supplied with excess (αв=1,2). The results of a numerical study showed that the diameter of peat particles affects the process of their combustion: coke particles with an initial diameter of 25 mkm to 250 mkm burn out by 96%. With an increase in particle diameter up to 1000 mkm, the degree of burn-out of coke decreases, but at the same time their removal decreases. It is shown that the furnace ensures the completeness of combustion of peat particles of peat 99.8%, volatiles is 100%.

The purpose of this research is to determine the effective way of implementation of the control algorithm, as an important functional part of information and control computer systems. The search criterion is the minimum of internal hardware FPGA resources required for the control unit implementation. This criterion allows miniaturization of dimensions, improves reliability by reducing the number of interconnections inside the chip, and ensures the possibility of a compact arrangement of various system components, which is especially important when using the “system-on-chip” design technology. The control unit holds a prominent place in the digital information and control systems. A comparative analysis of two control unit models represented as a finite state machine with either hard or programmable logic was proposed. Advantages and disadvantages of both models were determined according to the peculiarities of the information and control system algorithms, and, it was proved that the FSM model with a programmable logic matched these peculiarities in a greater degree. The purpose of this study was achieved due to the application of the proposed method for the implementation of the FSM with the programmable logic using the embedded memory of the FPGA and ProASIC chips. The main result was a substantial decrease in the LUT number used. The experimental results were obtained applying the chips of the world's top manufacturers - Xilinx, Altera/Intel, Microsemi. The studies were carried out based on the onboard computing complex control algorithm.

The evaluation of the possibility of using electromagnetic stirrers for dissimilar mixtures in various technological processes requires the study of their work under load conditions. The load mode of the agitator is ensured by the needle ferromagnetic elements moving inside a cylindrical working chamber under the influence of a rotating magnetic field, whose effectiveness can be predicted by analyzing the magnitude and nature of changes at the electromagnetic moment. The magnetic field ensures ordering of the ferromagnetic elements, therefore the magnetic permeability in it along the longitudinal and transverse axes becomes different. Due to the anisotropy of the magnetic properties of the composite medium in the working chamber, strong influences arise on this medium, based on the magnetic tension forces acting on the ferromagnetic elements. The purpose of this work was to present the method of calculation of the electromagnetic moment and determination of its dependence on the angular displacement of the rotating magnetic field of the inductor. The distribution of the magnetic induction inside the working chamber in the idle and load modes was compared, it gave an idea of the distribution of the magnetic field lines in those modes, set out the basic principles for calculation of the angular characteristics of the torque of the electromagnetic stirrer. The proposed method was based on the multi-position numerical calculations of the magnetic fields in the FEMM software package. Comparative calculations of the angular characteristics of the torque were performed at different magnetic permeabilities of the composite medium in the working chamber.