• Energy Research
• US close
• IN close
• AU close
• ES close
• Solar Energy close

Abstract Thermal performance of three naturally ventilated public buildings in which the wind tower is an important architectural freature is studied. One of the three builidings as well as it's wind tower is instrumented for temperature, relative humidity and airflow velocity measurements, and the other two are instrumented for temperature measurement. The results have led to a discussion concerning the degree of wind tower effectiveness in achieving thermal comfort.

Abstract The albedo of a roof determines the fraction of incoming sunlight that is reflected, which affects heat transfer into the building and exchange of energy between the built environment and the atmosphere. While the albedo of individual roofs can be easily measured, roof albedo at the city scale is unknown. In this paper we characterize the albedos of roofs in seven cities in California: Los Angeles, Long Beach, Bakersfield, San Francisco, San Jose, Sacramento, and San Diego. The fraction of urban area covered by roofs ranged by city from 10% to 25%. City-wide average roof albedo ranged from 0.17 ± 0.08 to 0.20 ± 0.11 (mean ± standard deviation) for five of the cities; values were higher in Sacramento (0.24 ± 0.11) and San Diego (0.29 ± 0.15). Buildings with small roofs were found to constitute a large fraction of city roof area and to have low mean albedos. This suggests that efforts to increase urban albedo through the use of reflective roofs should include small roofs, which are presumably mostly residential. Roof albedos derived for Bakersfield were used in a regional climate model (Weather Research and Forecasting Model) to estimate temperature changes attainable by converting the current stock of roofs to “cool” high albedo roofs. It was found that seasonal mean afternoon (15:00 LST) temperatures could be reduced by up to 0.2 °C during both the summer and winter. Changes in precipitation were not significant at the 95% confidence level.

Abstract An electrochemical conversion technique has been developed to deposit selective black nickel coatings of solar absorptance 0.90–0.94 and thermal emittance (at 100°C) 0.08–0.15 on galvanized iron, zincated, and zinc electroplated aluminium surfaces. The effect of electrochemical conversion parameters on the microstructure, optical and thermal properties and durability of the coatings has been established.

The integration of residential photovoltaic (PV) systems for self-consumption is expected to unlock a variety of economic, technical and social benefits, such as the creation of local work and the reduction of the price of electricity, CO2 emissions and electrical power losses in the transmission network. In spite of all these advantages, regulatory barriers prevented the development of renewable self-consumption in Spain prior to October 2018, when a new regulation introduced the right to self-consume electrical energy without charges. This work aims to estimate the effect of residential self-consumption on the Iberian electricity market. To achieve this goal, a ceteris paribus approach was adopted, the accumulated scattered PV self-production was turned into a reduction of the aggregate demand in the market and the new clearing point was established. Based on 2017 market data, the results showed that a 1% curtailment of the annual demand due to PV self-consumption could reduce the cost of the market-traded energy by almost 2%. European Commission, Horizonte 2020 SI-1778/12/ 2018

Abstract Solar water evaporation has been a topic of interest in recent years due to its applications in desalination, power generation, and heating. As water is not a good absorber of light, seeding it with light-absorbing particles can enhance evaporation efficiency. Activated carbon (AC) is one such material with desirable absorption properties for this application. However, particle sizes in granular and powder activated carbon can vary significantly. In this work, AC particles of different sizes are analyzed and their effect on evaporation rate is studied. It is found that particle sizes less than or comparable to solar wavelength spectrum produce higher evaporation efficiencies under independent scattering conditions ( f v 0.6 % ). It is also found that the solar absorption coefficient reaches between 0.98 and 0.9 for a volume fraction as low as 0.01%. The evaporation efficiency is 57.3% and 38.2% higher than for pure water evaporation for size of 80 nm and 8 μm, respectively, for a volume fraction of 0.01%. A parametric analysis is performed to identify the respective effect on evaporation rate.

Abstract In this paper we propose a time-dependent, three-dimensional model for the efficiency of a nanofluid-based direct-absorption parabolic trough solar collector under a turbulent flow regime. The model consists of a system of equations: a partial differential equation for conservation of energy, and a time-dependent radiative transport equation describing the propagation of solar radiation through the nanofluid. Writing the model in dimensionless form reveals four controlling dimensionless numbers: one describing the relative importance of conduction and advection and three describing the heat loss to the surroundings. Realistic parameter values are applied to reduce the model further and these indicate that two of the dimensionless groups have a much smaller impact on the performance of the solar collector. We use the resulting solution for the temperature to calculate an analytic expression for the collector’s efficiency. This expression permits optimisation of design parameters such as particle loading, incoming radiative intensity, receiver dimensions, the inlet temperature, and solar concentration ratio.

Abstract A new method of tracking the maximum power point (MPP) of a photovoltaic (PV) module exploiting the effects of the inherent characteristic resistances of the photovoltaic cells is proposed in this paper. An analysis of the mathematical model of the IV characteristic of the PV module revealed a possibility of estimating the MPP from its characteristic parameters such as the open circuit voltage (Voc), short circuit current (Isc), series resistance (Rse) and the shunt resistance (Rsh). The first stage of estimation process, for obtaining the voltage at the MPP, was facilitated by the effects of the series and shunt resistance on the IV characteristic of the PV module and the second stage of estimation process was facilitated by the combined process of the first stage of estimation and the condition for extracting the maximum power from the mathematical model of the pv characteristic of the PV module. The estimated voltage at the MPP in the second stage of estimation was found very close to the true MPP. The effectiveness of tracking the MPP with the proposed method has closely matched with the true MPP. This was validated by the results obtained through simulations and experiments. An analysis of the effects of degradation on the performance of the proposed technique showed that the performance was excellent during the first few years and with the update of characteristic resistances in the proposed algorithm the performance was found to be almost invariant. The successful experimental results obtained with a 100 Wp PV module indicate that the technique can be favourably implemented for standalone PV power systems.

Abstract Exergy analysis is very helpful for reducing irreversibility and rising the efficiency of solar collectors. The major objective of the present study is to organize a review on exergy analysis of different parabolic solar collectors. The effects of various flows and geometrical parameters of parabolic thermal collectors on the exergy efficiency were presented and discussed. In addition, comparative study was carried out to select the best solar thermal system for maximum exergy efficiency with minimal thermal losses. This study indicated that the hybrid nanofluids enhanced the exergy efficiency significantly as compared to without hybrid nanofluids. Passive techniques comprising twisted tape inserts, fins and insertion of swirl devices in the stream for changing the stream patterns causes to interrupt the thermal boundary layer and accordingly high exergy efficiency. This review would also throw light on the scope for further research and recommendation for improvement in the existing solar thermal collectors. Finally, this work will be beneficial for the scholars working on exergy analyses of solar parabolic collectors.