• Energy Research
• 2016-2025close
• US close
• IN close
• AU close
• Solar Energy close

Abstract Solar water evaporation has been a topic of interest in recent years due to its applications in desalination, power generation, and heating. As water is not a good absorber of light, seeding it with light-absorbing particles can enhance evaporation efficiency. Activated carbon (AC) is one such material with desirable absorption properties for this application. However, particle sizes in granular and powder activated carbon can vary significantly. In this work, AC particles of different sizes are analyzed and their effect on evaporation rate is studied. It is found that particle sizes less than or comparable to solar wavelength spectrum produce higher evaporation efficiencies under independent scattering conditions ( f v 0.6 % ). It is also found that the solar absorption coefficient reaches between 0.98 and 0.9 for a volume fraction as low as 0.01%. The evaporation efficiency is 57.3% and 38.2% higher than for pure water evaporation for size of 80 nm and 8 μm, respectively, for a volume fraction of 0.01%. A parametric analysis is performed to identify the respective effect on evaporation rate.

Abstract Exergy analysis is very helpful for reducing irreversibility and rising the efficiency of solar collectors. The major objective of the present study is to organize a review on exergy analysis of different parabolic solar collectors. The effects of various flows and geometrical parameters of parabolic thermal collectors on the exergy efficiency were presented and discussed. In addition, comparative study was carried out to select the best solar thermal system for maximum exergy efficiency with minimal thermal losses. This study indicated that the hybrid nanofluids enhanced the exergy efficiency significantly as compared to without hybrid nanofluids. Passive techniques comprising twisted tape inserts, fins and insertion of swirl devices in the stream for changing the stream patterns causes to interrupt the thermal boundary layer and accordingly high exergy efficiency. This review would also throw light on the scope for further research and recommendation for improvement in the existing solar thermal collectors. Finally, this work will be beneficial for the scholars working on exergy analyses of solar parabolic collectors.

Abstract Cu2BaSn(S,Se)4 (CBTSSe) solar cells are emerging photovoltaic devices due to their high theoretical efficiencies of ~31%, environment-friendly and earth-abundant composition, low density of non-recombination defects, and so on. However, the record efficiency of CBTSSe solar cell is only 5.2%, showing the importance of studying their performance via numerical analysis to further enhance their practical efficiencies. In this paper, the effect of absorber and buffer layers on performances of Cu2BaSnS4 (CBTS) solar cells are firstly systematically studied via the SCAPS-1D software to provide a platform for the study of the effect of MoS2 interlayer on the performances of CBTS solar cells. The highest PCE of CBTS solar cell with a 30 nm CdS buffer layer is 11.87%. The PCE of CBTS solar cell with a 0.8 μm CBTS absorb layer is 12.51%, indicating that the CBTS solar cell is a potential low-cost solar cell due to its large optical absorption coefficient (α > 104 cm−1). The efficiency of CBTS solar cell is improved to 16.47% when the carrier concentration of CBTS is 1016 cm−3. The relationship between the performance of solar cell and the band gap, thickness, donor concentration, acceptor concentration of MoS2 interlayer is systematically investigated on the basis of the optimized efficiency. It is found that MoS2 interlayer plays an important role in the performance of CBTS solar cell. The p-type MoS2 has a beneficial effect on the efficiency improvement while the n-type MoS2 has a negative effect on the efficiency enhancement. The highest PCE of CBTS solar cell is as high as 18.28% when the thickness and the acceptor concentration of MoS2 are 4 nm and 1019 cm−3, respectively. Our simulation result provides a promising research direction to further improve the actual efficiency of the CBTS solar cell.

Abstract In this paper, the experimental performance of a 45 m2 solar field of non-tracking external compound parabolic (XCPC) collectors installed at the University of California, Merced is described. The solar field was operated during July-August 2020 in both clean and dirty conditions and at varying operating temperatures (70, 135, 170 °C) while operating an air heater, thermal evaporator, and double effect absorption chiller. Performance data was used to develop an instantaneous solar field performance model which was then incorporated into an annual performance model using TMY3 data to estimate yearly production from the solar field. The model predicts an annual generation of ∼1100 kWh/m2-year at 80 °C, ∼1000 kWh/m2-year at 100 °C, ∼900 kWh/m2-year at 120 °C, ∼800 kWh/m2-year at 140 °C, and ∼700 kWh/m2-year at 160 °C in California. The XCPC technology is currently expected to have an installed cost of $300/m2 and an annual operations and maintenance cost of $6.5/m2-year. Over a 25 year lifetime it provides a levelized cost of heat at 2–4 cents per kWhth delivered. This is below the cost of commercial natural gas in California and at temperatures ≤ 120 °C below the cost of industrial natural gas, which highlights the potential of the XCPC technology for decarbonizing thermal applications such as water and space heating, drying, sterilization, desalination, evaporation, low pressure steam, double effect absorption chilling, process heating, and more. The lifetime cost of emissions reductions is ∼$169 per metric ton of avoided CO2 when replacing natural gas, ∼$137/MT CO2 when replacing propane, and ∼$83/MT CO2 when replacing electric heating.

Abstract The stable Ni(OH)2 ultrafine nanosheet combined with Bi2MoO6 to form heterojunction have been fabricated successfully by a simple and mild one-step solvent-thermal method. In this work, the Ni(OH)2/Bi2MoO6heterojunction increased the absorption range of visible light compared to the pure Bi2MoO6, from the UV–visible diffuse reflectance spectrum (DRS), thus greatly improving the degradation rate of organic dyes. The Ni(OH)2/Bi2MoO6heterojunctionwith different proportions was prepared by a mild one-step solvothermal method by controlling the mass fraction ratio between the nickel source and the bismuth source. The morphology and structure of the heterojunction materials were characterized by afield emission scanning electron microscopy (SEM) and a field-emission high-resolution transmission electron microscope (TEM). In this experiment, the photocatalytic properties were demonstrated by the degradation of organic dye Rhodamine B by the prepared samples. The results showed that 2%Ni(OH)2/Bi2MoO6 composite had the strongest photocatalytic performance and the maximum degradation rate was about 98% (135 min) when the Rhodamine B was degraded by visible light irradiation. It also can be found that Bi2MoO6composited by Ni(OH)2ultrafine nanosheet, compared with pure Bi2MoO6, the photocatalytic performance is improved by decreasing the recombination rate of photogenic carriers.

Abstract Significant efforts have been made to improve the performance of the Cu(In1-xGax)Se2 (CIGS) solar cells by tuning the band gap of the CIGS absorber to match it with the solar spectrum. However, the performance of the current record-holding CIGS solar cells is still far from theoretical expectations. Various researchers reported that the open circuit voltage (Voc) and the fill factor (FF) degrade in wide band gap CIGS solar cells. However, the limiting factors on further boosting the efficiency are still a matter of debate. In this study, we focus on tuning the properties of the interfacial layer between the rear contact and the wide-gap CIGS absorber to lower the contact resistance and recombination rate. Based on the numerical simulation using SCAPS (a solar cell capacitance simulator), we find that a MoO3 interfacial layer with high work function is more effective than its MoSe2 counterpart in reducing the back barrier, which in turn increases the Voc and the FF of the solar cell. We further predict that an overall efficiency of 24% can be achieved by reducing the back surface recombination and Schottky barrier with sub-micrometer a thick CIGS absorber. This work puts forward a strategy to improve the efficiency of wide band gap CIGS solar cells whilst reducing the raw materials consumption.

Abstract One of the greatest challenges in a photovoltaic solar power generation is to keep the designed photovoltaic systems working with the desired operating efficiency. Towards this goal, fault detection in photovoltaic plants is essential to guarantee their reliability, safety, and to maximize operating profitability and avoid expensive maintenance. In this context, a model-based anomaly detection approach is proposed for monitoring the DC side of photovoltaic systems and temporary shading. First, a model based on the one-diode model is constructed to mimic the characteristics of the monitored photovoltaic array. Then, a one-class Support Vector Machine (1SVM) procedure is applied to residuals from the simulation model for fault detection. The choice of 1SVM approach to quantify the dissimilarity between normal and abnormal features is motivated by its good capability to handle nonlinear features and do not make assumptions on the underlying data distribution. Experimental results over real data from a 9.54 kWp grid-connected plant in Algiers, show the superior detection efficiency of the proposed approach compared with other binary clustering schemes (i.e., K-means, Birch, mean-shift, expectation–maximization, and agglomerative clustering).