• Energy Research
• US close
• EU close
• NL close

This report discusses the following topics on the operation of DOE Tritium facilities: Environment, Safety, and Health Aspects of Tritium; Management of Operations and Maintenance Functions; Safe Shutdown of Tritium Facilities; Management of the Facility Safety Envelope; Maintenance of Qualified Tritium Handling Personnel; DOE Tritium Management Strategy; Radiological Control Philosophy; Implementation of DOE Requirements; Management of Tritium Residues; Inconsistent Application of Requirements for Measurement of Tritium Effluents; Interdependence of Tritium Facilities; Technical Communication among Facilities; Incorporation of Confinement Technologies into New Facilities; Operation/Management Requirements for New Tritium Facilities; and Safety Management Issues at Department of Energy Tritium Facilities.

Abstract Flow behavior of particles in a two-dimensional spouted bed with a draft tube is studied using a continuous kinetic-friction stresses model. The kinetic stress of particles is predicted from kinetic theory of granular flow, while the friction stress is computed from a model proposed by Johnson et al. (1990) . A stitching function is used to smooth from the rapid shearing viscous regime to the slow shearing plastic regime. The distributions of concentration and velocities of particles are predicted in the spouted bed with a draft tube. Simulated results compare with the vertical velocity of particles ( Zhao et al., 2008 ) measured and in the spout bed with draft plates and solid circulation rate ( Ishikura et al., 2003 ) measured in the spouted bed with a draft tube. The impact of the friction stress of particles on the spout, annulus, fountain and entrancement regions is analyzed in gas–solid spouted bed with a draft tube. Numerical results show that the gas flow rate through the annulus increases with the increase of the entrainment zone. The solids circulation rate decreases with the decrease of inlet gas velocity and the height of the entrainment zone. The effect of spouting gas velocity on distributions of concentration, velocity and particle circulation is discussed.

The coupling of water-splitting catalysts to silicon photovoltaics enables direct solar-to-fuel conversion. Critical to the performance of such devices is the use of interfaces to protect silicon from the oxygen-evolving reaction (OER) and at the same time to provide Ohmic contact between the buried silicon junction and the immobilised OER catalyst. Presented herein are guidelines for constructing the Si|catalyst interface, which is a crucial building block for efficient direct solar-to-fuel conversion devices. We show that fluorinated-tin-oxide is an especially attractive interface for buried-junction devices.

Abstract With promising benefits such as traffic emission reduction, traffic congestion alleviation, and parking problem solving, Electric Vehicle (EV)-sharing systems have attracted large attentions in recent years. Different from other business modes, customers in sharing economy systems are usually price sensitive. Therefore, it is possible to shift the usage of shared EVs through a well-designed Dynamic Pricing Scheme (DPS), with the objective of maximizing the system operator's total profit. In this study, we propose a novel DPS for a large-scale EV-sharing network to address the EV unbalancing issue and satisfy the vehicle-grid-integration (VGI) service based on accurate station-level demand prediction. The proposed DPS is formulated as a complex optimization problem, which includes two Price Adjustment Level (PAL) decision variables for every origin-destination pair of stations. The two PALs are employed to affect the EV-sharing demand and travel time between each station pair, respectively. Physical and operational constraints from both EV demand and VGI service aspects are also included in the proposed model. Two case study are conducted to validate the effectiveness of the proposed method.

The energy considered as waste heat in industrial furnaces owing to inefficiencies represents a substantial opportunity for recovery by means of thermal energy storage (TES) implementation. Although conventional systems based on sensible heat are used extensively, these systems involve technical limitations. Latent heat storage based on phase change materials (PCMs) results in a promising alternative for storing and recovering waste heat. Within this scope, the proposed PCM-TES allows for demonstrating its implementation feasibility in energy-intensive industries at high temperature range. The stored energy is meant to preheat the air temperature entering the furnace by using a PCM whose melting point is 885 °C. In this sense, a heat transfer model simulation is established to determine an appropriate design based on mass and energy conservation equations. The thermal performance is analysed for the melting and solidification processes, the phase transition and its influence on heat transference. Moreover, the temperature profile is illustrated for the PCM and combustion air stream. The obtained results prove the achievability of very high temperature levels (from 700 to 865 °C) in the combustion air preheating in a ceramic furnace; so corroborating an energy and environmental efficiency enhancement, compared to the initial condition presenting an air outlet at 650 °C.

This study analyzes the impact of price shocks in three input and output markets critical to ethanol: gasoline, corn, and sugar. We investigate the impact of these shocks on ethanol and related agricultural markets in the United States and Brazil. We find that the composition of a country’s vehicle fleet determines the direction of the response of ethanol consumption to changes in the gasoline price. We also find that a change in feedstock costs affects the profitability of ethanol producers and the domestic ethanol price. In Brazil, where two commodities compete for sugarcane, changes in the sugar market affect the competing ethanol market.

Recycled polylactic acid (PLAr) was reinforced with treated nanocellulosic hemp fibers for biocomposite fabrication. Cellulosic fibers were extracted from hemp fibers chemically and treated enzymatically. Treated nanocellulosic fibers (NCF) were analyzed by Fourier-transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy. Biocomposite fabrication was done with PLAr and three concentrations of treated NCF (0.1%, 0.25%, and 1% (v/v)) and then studied for thermal stability and mechanical properties. Increased thermal stability was observed with increasing NCF concentrations. The highest value for Young’s modulus was for PLAr + 0.25% (v/v) NCF (250.28 ± 5.47 MPa), which was significantly increased compared to PLAr (p = 0.022). There was a significant decrease in the tensile stress at break point for PLAr + 0.25% (v/v) NCF and PLAr + 1% (v/v) NCF as compared to control (p = 0.006 and 0.002, respectively). No significant difference was observed between treatments for tensile stress at yield.