• Energy Research
• 7. Clean energy close
• US close
• GB close
• DE close

Abstract This paper investigates the performance of a variable ratio gearbox (VRG) used in a small fixed-speed wind turbine with active blades. The major components of the VRG-enabled drivetrain are an automatic-manual gearbox and squirrel cage induction generator that connects directly to the grid. The simplicity of this system may be appealing for applications when cost and reliability are of concern. It is an alternative to variable speed systems, which necessitate a modified generator and power conditioning equipment. During partial load operation the VRG provides a discrete set of rotor speeds. This allows the controller to track the wind speed and to achieve a greater efficiency. This study suggests three VRG ratios are sufficient to improve performance when used with active blades. A case study is presented where the performance is simulated using three different wind data sets. The study suggests that the VRG can improve production between 7 and 8.5% in low wind areas. The design procedure also illustrates a technique for finding the lowest and highest gear ratios needed for VRG design. These ratios allow the system to achieve the lowest cut-in and rated speeds. The approach also has useful implications for the design of a continuously variable transmission.

With the integration of a high penetration of wind power into distribution system, the ability to cope with the voltage fluctuation issue arising from the intensified uncertainty should be improved. Energy storage system (ESS) with effective control strategies keeps a key role in smoothing the voltage fluctuation caused by the uncertainty of wind turbine generators (WTGs). Considering the constraints of state of charge (SOC), charge-discharge efficiency and continuous operation of ESS, this paper proposes a novel approach to determine the minimum capacity of ESS to satisfy the voltage fluctuation limit based on unbalanced three-phase interval power flow. An unbalanced forward-backward sweep interval power flow considering the constraints of ESS and the voltage fluctuation limit is proposed. The interval model of uncertain WTG output is established on basis of wind speed fluctuation curve. The interval model of the practical ESS output is obtained on basis of the present SOC, nominal capacity and comprehensive efficiency. The output voltages of power flow can directly demonstrate the voltage fluctuation rate due to their interval forms. Therefore, a feedback mechanism is established between the output voltage fluctuation rate and the input ESS practical power, which is used to determine the minimum capacity of ESS to satisfy the fluctuation limit. A modified IEEE 33-bus system with high penetration of WTGs is implemented to test the proposed method. Results demonstrate the validity and effectiveness of the proposed approach.

Abstract A CFD modelling study has been undertaken to examine the co-firing of pulverised coal and biomass with particular regard to the burnout of the larger diameter biomass particles. Computations were based on a research combustion facility that replicates an industrial coal-fired power station. Three percent, by mass, of pinewood was blended with a bituminous UK coal, and the effects of the wood particle size and shape on the burnout of the combined wood and coal char were investigated. The effect of varying the devolatilisation and char combustion rate constants for the biomass component in the blend was also investigated. It was concluded that the combustion of small (200 μm) wood particles was rapid but the rate of combustion of larger particles was dependent on their composition, size, and shape.

The Sulphurdale Geothermal Field is located in Beaver County Utah, within the boundaries of the Cove Fort--Sulphurdale Known Geothermal Resource Area (KGRA). During the past year, three wells drilled in Section 7, T-26-S, R-6-W, have produced dry steam from a fractured volcanic formation located at a depth of about 1100 feet. Two of these three wells are currently prepared to supply steam to a power plant, and one well has been plugged and abandoned. ThermaSource, Inc. was retained by Mother Earth Industries, the operator of the field, to conduct well tests and render an opinion as to the nature of the geothermal reserves and assess the commercial potential of these reserves. Because of the limited area that has been explored to date, there can be no assurance that the reserves estimate will prove accurate. Project economics are based on parameters believed to be accurate, but there is no assurance that such cash flow projections will be realized.

The Severn Estuary has the world's second largest tide range and a barrage across the estuary, located just seawards of Cardiff in Wales and Weston in the South West England, has been proposed for over half a century, with the objective of extracting large amounts of tidal energy. A Severn Barrage, as previously proposed by the Severn Tidal Power Group (STPG), would be the largest renewable energy project for tidal power generation in the world, if built as proposed, and would generate approximately 5% of the UK's electricity needs. However, concerns have been raised over the environmental impacts of such a barrage, including potential increase in flood risk, loss of intertidal habitats etc. In addressing the challenges of maximizing the energy output and minimizing the environmental impacts of such a barrage, this research study has focused on using a Continental Shelf model, based on the modified Environmental Fluid Dynamics Code (EFDC) with a barrage operation module (EFDC_B), to investigate both the far and near field hydrodynamic impacts of a barrage for different operating scenarios. Three scenarios have been considered to simulate the Severn Barrage, operating via two-way generation and using different combinations of turbines and sluices. The first scenario consisted of 216 turbines and 166 sluices installed along the barrage; the second consisted of 382 turbines with no sluices; and the third consisted of 764 turbines and no sluices. The specification of the sluice gates and turbines are the same for all scenarios. The model results indicate that the third scenario has the best mitigating effects for the far-field and near-field flood risks caused by a barrage and produces the most similar results of minimum water depth and maximum velocity distributions to those obtained from simulating the natural conditions of the estuary, i.e. the current conditions. The results also show that the flow patterns around the barrage are closest to those for the existing natural conditions with minimal slight changes in the estuary. Thus, the results clearly indicate that the environmental impacts of a Severn Barrage can be minimized if the barrage is operated for two-way generation and under the third scenario. Although it appears that the energy output for the third scenario is less than that obtained for the other two scenarios, if very low head (VLH) turbines are used, then the third scenario could generate more energy as more turbines could be cited along the barrage structure. Therefore, the study shows that a Severn Barrage, operating in two-way generation and with 764 turbines (ideally VLH turbines), would be the best option to meet the needs of maximizing the energy output, but having a minimal impact on environmental changes in the estuary and far-field.

Biomass plays an important role in the world primary energy supplies, currently providing ∼14% of the world's primary energy needs and being the fourth largest contributor following coal, oil and natural gas. Over the past decade, domestic biomass heating has received more governmental and public supports than ever before in many developed countries, such as the UK. Although biomass combustion releases some combustion pollutants, biomass is renewable and produces little net CO 2 emissions to the atmosphere. Owing to the low sulphur and low nitrogen contents of many biomass materials, substituting biomass for fossil fuels, particularly coal, can reduce SO x and NO x emissions. This study investigated flue gas emissions, particularly carbon monoxide and nitrogen oxides, of a domestic biomass boiler under various operating conditions. The biomass boiler used in this study satisfies the current EU regulation (EN 303-05) on emissions of domestic biomass boilers. Emissions of the boiler had been measured not only under normal combustion conditions, but also under 'idle' combustion conditions when the boiler was not in but was ready for full operation. The experimental results are analysed and presented in this paper. Copyright The Author 2010. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oxfordjournals.org, Oxford University Press.

Dynamic loading of transformers is the term used when the loading capacity is calculated using an appropriate thermal model while taking into account the load magnitude, load shape, thermal limits and external cooling conditions. For transformer dynamic loading, the aim is to estimate the transformer's maximum dynamic loading capacity without violating the hottest-spot temperature (HST) and top-oil temperature (TOT) thermal limits. These two temperatures are proxy measures of insulation temperature, which can be used to estimate the loss of service life. The accuracy of the TOT and HST predictions is dependent on many things, central to which is the accuracy of the thermal model. This paper introduces metrics that can be used to differentiate between reliable and unreliable transformer thermal models. The two models discussed in this paper for HST and TOT are the non-linear IEEE model and the model developed by the authors using linear regression methods.

Facile sol–gel synthesis of Mo:BiVO4 thin films with optimized morphology results in reduced surface recombination and enhanced hole transfer efficiency.

Abstract For 118 million residential housing units in the U.S., there is currently a gap between the potential energy savings that can be achieved through the use of existing energy efficiency technologies, and the actual level of energy savings realized, particularly for the 37% of housing units that are considered residential rental properties. Additional quantifiable benefits are needed beyond energy savings to help further motivate residential property owners to invest in energy efficiency upgrades. This research focuses on assessing the adoption of energy efficient upgrades in U.S. residential housing and the impact on rental prices. Ten U.S. cities are chosen for analysis; these cities vary in size across multiple climate zones, and represent a diverse set of housing market conditions. Data was collected for over 159,000 rental property listings, their characteristics, and their energy efficiency measures listed in rental housing postings across each city. Following an extensive data quality control process, over thirty different types energy efficient features were identified. The level of adoption was determined for each city, ranging from 5.3% to 21.6%. Efficient lighting and appliances were among the most common, with many features doubling as energy efficient and other desirable aesthetic or comfort improvements. Then using propensity score matching and conditional mean comparison methods, the relative impact on rent charged in each city was calculated, which ranged from a 6% to 14.1% increase in rent for properties with energy efficient features, demonstrating a positive economic impact of these features, particularly for property owners. This was further subdivided into five types of energy efficiency upgrade and three housing types. Single family homes generally demanded higher premiums with energy efficient features, however there was not a consistent pattern across the types of efficient upgrades. The results of this work demonstrate that investment in energy efficient technologies has quantifiable benefits for rental property owners in the U.S. beyond just energy savings. This methodology and results can also be used in other cities and by property owners, utility companies, or others, ultimately encouraging further investment and positive economic impact in residential energy efficiency and in turn improving energy and resource conservation in the building sector.