• Energy Research
• Closed Access close
• other engineering and technologies close
• US close
• KR close

Abstract The accurate information of the thermal stresses and temperature in isotropic elastic solids is the key for many engineering applications. At present the classical linear coupled theory of thermoelasticity deduced with the assumptions of small temperature changes is widely used to solve the thermoelastic problems in engineering. In this paper, to describe the thermoelastic behavior in isotropic solids undergoing large temperature changes more accurately, the novel coupled models of thermoelasticity and the corresponding finite element models have been presented explicitly and validated by experimental measurement. The effect of large temperature changes on the solutions of thermoelastic problems is discussed. For the heat transfer process, if the isotropic elastic solids will expand when heated and contract when cooled and the condition d E E d T · σ i j E − δ i j 1 − 2 ν α 0 can be met in the context of small deformations, the effect of large temperature changes can be regarded as increasing the specific heat. The proposed models are applied to solve two thermoelastic problems. From the obtained numerical results, the effect of large temperature changes will increase with the amplitude of temperature change and may be considerably even when the temperature changes slowly.

Abstract The analysis and optimization of flat plate fins of constant thickness and straight base has been conducted for different fin’s shapes. Performance of the fins is quantified through effectiveness and expressed as a function of fin’s shape, width, and area. A linear piecewise function with varying number of evenly spaced sections is used to generate shapes with different number of degrees of freedom, which are classified as constrained- or unconstrained-base depending on the width of the fin at the constant temperature base location. For one- and two-degrees of freedom shapes, a variety of rectangular, triangular, trapezoidal, and rhomboidal geometries are considered and optimized. For more than two-degrees of freedom, more complex resulting shapes are also considered. By adjusting the value of the corresponding shape parameters, the best possible distributions of available area to maximize heat transfer are obtained, which produce significant improvements favored by smaller width and larger area. Unconstrained-base performs better than constrained-base configurations as they allow the distribution of a larger area close to the high-temperature base. Optimal shape of unconstrained-base fins is in general convergent with non-zero wide tip, while, for constrained-base fins, it is divergent in the first linear section from the base and convergent in the remaining ones. For increasing number of degrees of freedom the optimized shapes tend to resemble natural structures while effectiveness increases asymptotically to a limit for constant width and area. Besides determining the optimal configurations, consideration has been made about the optimal regions where a variety of shapes produce virtually the same effectiveness of the absolute maximum, which can be used to design fins with almost maximum performance but having simpler shapes or being functional under possible space restrictions. The dimensionless model and the systematic analysis proposed in this work are not only appropriate to study a wide range of flat plate fins but also can be implemented to analyze and perform optimization over other type of fins and fins configurations.

Abstract Pollution control strategies currently in use by electric power systems are reviewed and a new minimum emission dispatch (MED) method is developed. This new method minimizes overall emission levels at an increased cost in large-scale power systems while simultaneously accommodating local pollution level requirements, as well as economic constraints.

Accurate predictions of fuel spray behavior and mixture formation in simulations of direct-injection spark-ignition (DISI) engines are fundamental to ensure proper description of all subsequent processes including ignition, combustion, and emissions. In this work, the spray evolution in a single-cylinder optical DISI engine was studied experimentally and numerically with the goal of enabling predictive computational fluid dynamics (CFD) modeling of in-cylinder sprays. The authors explored a wide range of operating conditions characterized by several fuel injection temperatures and engine speeds, using a well-characterized nine-component gasoline surrogate known as PACE-20. The effect of flash boiling and intake crossflow on the spray is discussed, with a focus on evaluating the ability of the spray models to capture highly transient spray behavior. In the experiments, the fuel temperature was varied between 20°C and 80°C, allowing for non-flash- to flash-boiling transition to emerge with enhanced flashing intensity at the highest temperatures. Spray collapse resulted in vapor-rich regions, owing to the locally lower inertia of the fluid. Varying the engine speed from 650 to 1950 rpm promoted increasingly more turbulent in-cylinder crossflow which interacted with the spray during the injection event and resulted in enhanced spray dispersion. The CFD model was able to capture the spray morphology transition at different fuel temperatures and engine speeds adequately. It is shown that the spray breakup model could capture the transitional spray behavior induced by flash boiling atomization and intake flow via proper initialization of the spray cone angle and calibration of the spray models’ constants.

Abstract Building energy performance is often inadequate given design goals. While different types of assessment methods exist, they either do not consider design goals and/or are not general enough to integrate new and innovative energy concepts. Furthermore, existing assessment methods focus mostly on the building and system level while ignoring more detailed data. With the availability and affordability of more detailed measured data, the increased number of measured data points requires a structure to organize these data. This paper presents the Energy Performance Comparison Methodology (EPCM), which enables the identification of performance problems based on a comparison of measured data and simulated data representing design goals. The EPCM is based on an interlinked building object hierarchy that structures the detailed performance data from a spatial and mechanical perspective. This research is developed and tested on multiple case studies that provide real-life context and more generality compared to single case studies.

The diffusivity and solubility of fluorine in solid nickel were determined using the following solid-state electrochemical cells: Co + CoF2| BaF2| Ni | BaF2| Co + CoF2 Co + CoF2| CaF2| BaF2| Ni | BaF2| CaF2| Co + CoF2 In the temperature range 1023 to 1223 K, the diffusion coefficient of fluorine in solid nickel is given by: 1 $$D_F (cm^2 /s) = (2.13_{ - 1.54}^{ + 5.54} ) \times 10^{ - 3} \exp (( - 118,600 \pm 12,000J/mol)/RT)$$ The dissolution of atomic fluorine in solid nickel obeys Sieverts’ law; however, the solubility results showed considerable scatter. In the temperature range 1073 to 1223 K, the mean solubility of fluorine in solid nickel, corresponding to the equilibrium Ni + NiF2, follows the relationship: N -F S (at. pct) = 5.73 x 10-3 exp((10,850 J/mol)/RT)

Abstract Flow behavior of particles in a two-dimensional spouted bed with a draft tube is studied using a continuous kinetic-friction stresses model. The kinetic stress of particles is predicted from kinetic theory of granular flow, while the friction stress is computed from a model proposed by Johnson et al. (1990) . A stitching function is used to smooth from the rapid shearing viscous regime to the slow shearing plastic regime. The distributions of concentration and velocities of particles are predicted in the spouted bed with a draft tube. Simulated results compare with the vertical velocity of particles ( Zhao et al., 2008 ) measured and in the spout bed with draft plates and solid circulation rate ( Ishikura et al., 2003 ) measured in the spouted bed with a draft tube. The impact of the friction stress of particles on the spout, annulus, fountain and entrancement regions is analyzed in gas–solid spouted bed with a draft tube. Numerical results show that the gas flow rate through the annulus increases with the increase of the entrainment zone. The solids circulation rate decreases with the decrease of inlet gas velocity and the height of the entrainment zone. The effect of spouting gas velocity on distributions of concentration, velocity and particle circulation is discussed.

Abstract The combination of biomass gasification with fuel cells, especially high temperature Solid Oxide Fuel Cells (SOFCs) promises sustainable and highly efficient (decentralized and modular) energy conversion systems. This review encompasses the components of biomass integrated gasification–SOFC technology including biomass characteristics, the thermochemical conversion in gasifiers and the factors affecting the gasification process, the cleaning technologies for raw producer gas and its conditioning and finally the integration of gasifier with SOFCs. The influence of impurities present in biomass producer gas such as particulates, tar, H 2 S, HCl and alkali compounds based on recent experimental studies and their tolerance limits towards SOFCs are presented. Even though analysis based on the probable tolerance limits of impurities towards SOFCs and a comprehensive overview of the cleaning technologies for producer gas impurities indicate that producer gas cleaning at various temperatures using current technologies to meet SOFC requirements is possible, more experimental studies are still needed to acquire the detailed information on the tolerance limits of impurities for SOFCs. The recent theoretical modeling and experimental studies of biomass integrated gasification–SOFC systems are also presented.