• Energy Research
• 12. Responsible consumption close
• US close
• NL close

In this study, levulinic acid (LA) was produced from rice straw biomass in co-solvent biphasic reactor system consisting of hydrochloric acid and dichloromethane organic solvent. The modified protocol achieved a 15% wt LA yield through the synergistic effect of acid and acidic products (auto-catalysis) and the designed system allowed facile recovery of LA to the organic phase. Further purification of the resulting extractant was achieved through traditional column chromatography, which yielded a high purity LA product while recovering ∼85% wt. Upon charcoal treatment of the resultant fraction generated an industrial grade target molecule of ∼99% purity with ∼95% wt recovery. The system allows the solvent to be easily recovered, in excess of 90%, which was shown to be able to be recycled up to 5 runs without significant loss of final product concentrations. Overall, this system points to a method to significantly reduce manufacturing cost during large-scale LA preparation.

As the concern with global warming increases causing the need for CO2 reduction, renewable energy is of great interest as it has lower carbon footprint when compared to conventional sources (natural gas, coal, oil and nuclear). Solar energy has been drawing worldwide attention since it can transform sunlight directly into electricity with the use of photovoltaic (PV) cells. However, this technology has some drawbacks that need to be addressed including dust deposition on solar panels, also known as soiling. Soiling can decrease PV panel's efficiency thereby resulting in less energy production. The soiling rates are very site specific and depend on the geographic location of the panels and the climate in that area. The solar panels can be cleaned naturally (by rainfall, snow or wind) or mechanically washed. This thesis addresses the impact of solar panel soiling and washing on the energy production of solar PV plants located at the UNLV campus. The objectives of this project were (a) to evaluate whether rainfall alone, in the desert environment with low rainfall, is sufficient to clean up the solar panels, and, if possible, determine the minimum amount of rainfall necessary to clean up panels.; (b) to examine the efficiency loss caused by soiling using different methods of analyses and (c) to evaluate if panel washing is worthwhile given the cost and the efficiency gain that is obtained by washing. To calculate the efficiency of the panels, a model was developed to generate parameters that were not measured at the site. Panel efficiencies before and after rainfall events were compared to determine the minimum amount of rain necessary to clean the panels. It was found that at least 0.2 inches of rain was needed to partially restore clean-panel efficiency. In Las Vegas, the recurrence periods of different depths rainfall were calculated using data from the past 29 years. It was observed that the 50th percentile recurrence period of a rainfall event with depth of 0.2 inches or higher was approximately 52 days. Student Union: -0.0044%/day, CBC-C: -0.00099%/day, and Dayton Hall: -0.0034%/day The amount of efficiency lost during the dry intervals (periods between rainfall events) was analyzed in three different ways. The average efficiency loss per day during the dry periods varied from -0.000171 % to -0.00533 %, depending on the method used and the building where the panels were located. However, there were some limitations to the calculations. It was not possible to completely isolate the effects of only soiling on the efficiency of the panels. The rate of decline seemed to be also impacted by seasonal effects. To better evaluate the effect of washing, a professional company was hired to wash a set of solar panels located on UNLV's Student Union building. The panels were washed with water with a low concentration of TDS. The power output and the efficiency of those panels were analyzed from before and after the washing. There was a very small efficiency and power increase due to the washing. Therefore, it was concluded that washing in this area is not worthwhile, and that rainfall events in excess of 0.2 inches can adequately restore the efficiency of the panels. If there is a change in cost of energy, washing, water or a great increase in the efficiency of the solar panels, it would be necessary to reevaluate the analysis.

AbstractClimate change poses new and unique challenges that threaten lives and livelihoods. Given the increasing risks and looming uncertainty of climate change, increasing attention has been directed towards adaptation, or the strategies that enable humanity to persist and thrive through climate change the best it can. Though climate change is a global problem often discussed at the national scale, urban areas are increasingly seen as having a distinct role, and distinctive motivation and capacity, for adaptation. The 12 articles in this special issue explore ways of understanding and addressing climate change impacts on urban areas. Together they reveal young but rapidly growing scholarship on how to measure, and then overcome, challenges of climate change. Two key themes emerge in this issue: 1) that we must identify and then overcome current barriers to urban adaptation and 2) frameworks/metrics are necessary to identify and track adaptation progress in urban settings. Both of these themes point to the power of indicators and other quantitative information to inform priorities and illuminate the pathway forward for adaptation. As climate change is an entirely new challenge, careful measurement that enables investment by private and public parties is necessary to provide efficient outcomes that benefit the greatest number of people.

Recycled polylactic acid (PLAr) was reinforced with treated nanocellulosic hemp fibers for biocomposite fabrication. Cellulosic fibers were extracted from hemp fibers chemically and treated enzymatically. Treated nanocellulosic fibers (NCF) were analyzed by Fourier-transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy. Biocomposite fabrication was done with PLAr and three concentrations of treated NCF (0.1%, 0.25%, and 1% (v/v)) and then studied for thermal stability and mechanical properties. Increased thermal stability was observed with increasing NCF concentrations. The highest value for Young’s modulus was for PLAr + 0.25% (v/v) NCF (250.28 ± 5.47 MPa), which was significantly increased compared to PLAr (p = 0.022). There was a significant decrease in the tensile stress at break point for PLAr + 0.25% (v/v) NCF and PLAr + 1% (v/v) NCF as compared to control (p = 0.006 and 0.002, respectively). No significant difference was observed between treatments for tensile stress at yield.

Abstract The combination of biomass gasification with fuel cells, especially high temperature Solid Oxide Fuel Cells (SOFCs) promises sustainable and highly efficient (decentralized and modular) energy conversion systems. This review encompasses the components of biomass integrated gasification–SOFC technology including biomass characteristics, the thermochemical conversion in gasifiers and the factors affecting the gasification process, the cleaning technologies for raw producer gas and its conditioning and finally the integration of gasifier with SOFCs. The influence of impurities present in biomass producer gas such as particulates, tar, H 2 S, HCl and alkali compounds based on recent experimental studies and their tolerance limits towards SOFCs are presented. Even though analysis based on the probable tolerance limits of impurities towards SOFCs and a comprehensive overview of the cleaning technologies for producer gas impurities indicate that producer gas cleaning at various temperatures using current technologies to meet SOFC requirements is possible, more experimental studies are still needed to acquire the detailed information on the tolerance limits of impurities for SOFCs. The recent theoretical modeling and experimental studies of biomass integrated gasification–SOFC systems are also presented.

Steel is an indispensable material for the sustainable maintenance and progress of modern civilization. Its versatility in terms of mechanical and thermal characteristics, corrosion resistance, raw material availability, energy consumption and recyclability provides a clear advantage in a fast-changing technological landscape. In order to adapt to the changing needs, steel production methods have been evolving and improving over time. One such improvement opportunity in terms of energy efficient production is the ”heat pipe assisted annealing” concept. The cold rolling of steel is a process where the steel strip is cold-worked by means of rolls to achieve thickness reduction and better uniformity. This results in the strain hardening of steel. To reduce the hardness of steel and to render it more workable, it is thermally treated by heating it to a target soaking temperature and then cooling it down. This process is called annealing and it is an energy intensive process. Conventionally, heating is achieved with natural gas fired furnaces, whereas cooling is done using convective gas cooling. With this setting, the thermal energy extracted from the steel strip during the cooling stage is not used in any way. Moreover, none of the energy that is introduced during the heating stage is retained in the final product.An alternative technology for the annealing of steel was developed at Tata Steel IJmuiden R&D with the objective of recovering and using some of the heat removed during the cooling stage and thus, achieving more energy efficient annealing. With this technology called heat pipe assisted annealing, the cooling strip is thermally linked to the heating strip with multiple rotating heat pipes. In this way, each heat pipe transfers a certain amount of heat from the cooling strip to the heating strip. Only final heating and cooling of the steel strip is carried out in a conventional way. This concept is applicable to relatively low temperature (sub-critical) annealing where the cooling rate is not crucial. Therefore, packaging steel is a good candidate for the application of this technology.A rotating heat pipe is a highly efficient heat transfer device which is a wickless hollow cylindrical vessel rotating around its symmetric axis and containing a fixed amount of working fluid. The working fluid acts as a thermal energy carrier, transporting heat from one end of the heat pipe to the other. This basically occurs in four steps: (i) heat added to the evaporator part of the heat pipe causes the evaporation of the liquid, (ii) vapor travels to the condenser end of the heat pipe due to pressure difference, (iii) vapor condenses in the condenser section where heat is removed from the heat pipe, (iv) liquid returns to the evaporator with the help of the static pressure head and the centrifugal force induced by rotation. The heat pipe assisted annealing concept has been patented and subsequently further studied by Tata Steel Europe R&D. A water-filled rotating heat pipe test rig integrated with steel strips provided the bulk of the prior work. This test rig served as the proof-of-principle installation and it showed that heat can be transported from a hot strip to a cold one with a rotating heat pipe. In this context, several gaps have been identified to further acquire the knowledge on the system components, the concept performance and feasibility.This thesis focuses on four main aspects of the fundamentals and the feasibility of the heat pipe assisted annealing concept: (i) contact heat transfer between the steel strip and the rotating heat pipe, (ii) computationally efficient modelling of the interior dynamics of a rotating heat pipe, (iii) applicable working fluids for the high temperature range, (iv) behavior of the heat pipe assisted annealing system as a whole. These aspects are studied through a thermal engineering perspective. The heat pipe assisted annealing concept relies on the effective transfer of heat from the strip to the rotating heat pipe and vice versa. Therefore, it is important to understand the underlying physics governing this heat transfer and to be able to predict the heat transfer rate for possible configurations. In this context, in Chapter 2 of this thesis, the contact heat transfer between a steel strip and a rotating heat pipe is investigated both experimentally and numerically. The numerical model is based on first principles. It finds the thickness and the pressure of the gas layer between the strip and the heat pipe and subsequently considers different heat transfer mechanisms. The experimental work was carried out on the proof of- principle test rig. The model is validated with the experimental results. The contact heat transfer coefficient in the uniform region varied between 4,000 to 20,000 W/(m2.K). It showed an increase in the contact heat transfer with decreasing strip velocity and increasing radial stress. For the considered cases, conduction through the gas layer was the dominant heat transfer mechanism. Additionally, a simplified expression has been developed for the calculation of contact heat transfer through multiple regression analysis. The modelling of a rotating heat pipe is a crucial step for the detailed study of the heat pipe assisted annealing technology. Although modelling of rotating heat pipes has been the subject of many studies in the literature, these models are not computationally efficient enough to allow for the simultaneous modelling of multiple heat pipes linked to each other with strips. On this ground, in Chapter 3, a novel computationally efficient engineering model describing the transient behavior of the heat pipe is developed. In this model, the liquid and the vapor cells are allowed to change size radially in order to allow for the tracking of the liquid / vapor interface without the need for fine meshing or re-meshing. The model is also adapted to capillary-driven heat pipes. The model is validated with experimental and numerical studies from the literature. The deviation is computed to be around 2% with the numerical and analytical studies and around 6% with the experimental study.The heat pipe assisted annealing concept requires the operation of heat pipes within a temperature range of 25 °C to 700 °C. In order to operate within this range, different working fluids need to be used for different temperature ranges due to constraints of vapor pressure, life time, performance and safety. These working fluids are studied in Chapter 4. First, a selection of the working fluids is made based on a literature review. This selection yielded water, Dowtherm A, phenanthrene and cesium. Then, a life time test has been carried out with thermosyphons to test the stability of phenanthrene. At the end of a 3 months long test at 460 °C, thermal decomposition of phenanthrene was observed. However, these tests should be repeated with better initial vacuum and at multiple temperatures. Finally, Dowtherm A has been used in a rotating heat pipe setup to test its applicability and performance. It has been shown that Dowtherm A is suitable to be used in a rotating heat pipe at the designated temperature range in terms of performance, provided that annular flow is avoided. With the knowledge gathered from the previous chapters of this thesis, a model of the heat pipe assisted annealing line has been developed in Chapter 5. The aim of this model is to quantify the energy efficiency advantage brought by the concept for different number of heat pipes and to understand the behavior of the system as a whole. The simulations were run for a fixed plant layout with varying number of heat pipes and an average wrap angle of 104°. The energy recoveries for the simulations run for a strip of 0.25 mm and a line speed of 6.133 m/s were 76.5%, 73.4%, 69.4% and 63.9% for a total number of 90, 75, 60 and 45 heat pipes, respectively. From the simulation results it follows that cesium heat pipes are more efficient than organic heat pipes. Finally, the simulation results showed that the thermal cycle requirements can be satisfied with this new technology. Large Scale Energy Storage

Sustainability of agro-food supply chains has recently become the subject of greater interest from consumers, firms, governmental organizations and academia as the environment continues to deteriorate. One of the most critical factors influencing the sustainability of an agro-food supply chain is its network design. A particularly challenging aspect in this context is the broad range of influencing indicators associated with the Triple Bottom Line (TBL) of sustainability that need to be considered. However, many of these indicators could not be fully integrated or measured by single-step optimization problems. This paper presents a critical literature review of operational research methods for the design of sustainable supply chains. A novel two-stage hybrid solution methodology is proposed. In the first stage, a partner selection is performed using a hybrid multi criteria decision making based on Analytic Hierarchy Process (AHP) method and the Ordered Weighted Averaging (OWA) aggregation method. The result obtained in the first stage is used in the second stage to develop a multi-objective mathematical model to optimize the design of the supply chain network. This approach allows the simultaneous consideration of all three dimensions of sustainability including carbon footprint, water footprint, number of jobs created and the total cost of the supply chain design. The proposed approach generates a Pareto frontier to aid users in making decisions. Numerical experiments are completed utilizing data from an agro-food company to demonstrate the efficiency and effectiveness of the proposed solution methodology. The analyzes of the numerical results provide important organizational, practical and policy insights on (1) the impact of financial and environmental sustainability on supply chain network design (2) the tradeoff analysis between environmental emission, water footprint, societal implications and associated cost for making informed decision on supply chain investment.

The Houston-Dallas (I-45) corridor is the busiest route among 18 traffic corridors in Texas, USA. The expected population growth and the surge in passenger mobility may result in a significant impact on the regional environment. This study uses a life cycle framework to predict and evaluate the net changes of environmental impact associated with the potential development of a high-speed rail (HSR) System along the I-45 corridor through its life cycle. The environmental impact is estimated in terms of CO2 and greenhouse gas (GHG) emissions per vehicle/passenger-kilometers traveled (V/PKT) using life cycle assessment. The analyses are performed referring to the Ecoinvent 3.4 inventory database through the phases: material extraction and processing, infrastructure construction, vehicle manufacturing, system operation, and end of life. The environmental benefit is evaluated by comparing the potential development of the HSR system with those of the existing transportation systems. The vehicle component, especially operation and maintenance of vehicles, is the primary contributor to the total global warming potential with about 93% of the life cycle GHG emissions. For the infrastructure component, 56.76% of GHG emissions result from the material extraction and processing phase (23.75 kgCO2eq/VKT). Various life cycle emissions of HSR except PM are significantly lower than for passenger cars.