• Energy Research
• Open Access close
• Open Source close
• US close
• SA close

In the present study, we explored the temperature evolution and hydrogen desorption properties of the Mg50Ni50 alloy through both numerical simulation and experimental analyses. Desorption kinetics characterization was carried out using the volumetric method, specifically employing a Sievert's-type apparatus to investigate solid-gas reactions. The experiments covered a temperature range from 313 K to 353 K, with an initial hydrogen pressure of 12 bar. Simultaneously, a mathematical approach was employed to numerically investigate the temperature evolution within the hydride bed. Using COMSOL Multiphysics as a simulator, a numerical simulation was conducted based on experimental data. The study examined the impact of cooling temperature on hydride temperature evolution. Results revealed that hydrogen desorption kinetics of the amorphous Mg50Ni50 alloy are more significant compared to those of Mg2Ni compounds. Moreover, the effect of the warming temperature on the equilibrium pressure can also be observed in the hydrogen desorption isotherm curves. The experimental study of the Mg50Ni50 alloy provided activation energy data, along with determination of hydride formation enthalpy and entropy. On the other hand, we showed that the hydride temperature is maximum at the hydride-hydrogen interface within the hydride center.

This article examines land-use, market and welfare implications of lignocellulosic bioethanol production in Hawaii to satisfy 10% and 20% of the State's gasoline demand in line with the State's ethanol blending mandate and Alternative Fuels Standard (AFS). A static computable general equilibrium (CGE) model is used to evaluate four alternative support mechanisms for bioethanol. Namely: (i) a federal blending tax credit, (ii) a long-term purchase contract, (iii) a state production subsidy financed by a lump-sum tax and (iv) a state production subsidy financed by an ad valorem gasoline tax. We find that because Hawaii-produced bioethanol is relatively costly, all scenarios are welfare reducing for Hawaii residents: estimated between -0.14% and -0.32%. Unsurprisingly, Hawaii.s economy and its residents fair best under the federal blending tax credit scenario, with a positive impact to gross state product of $49 million. Otherwise, impacts to gross state product are negative (up to -$63 million). We additionally find that Hawaii-based bioethanol is not likely to offer substantial greenhouse gas emissions savings in comparison to imported biofuel, and as such the policy cost per tonne of emissions displaced ranges between $130 to $2,100/tonne of CO2e. The policies serve to increase the value of agricultural lands, where we estimate that the value of pasture land could increase as much as 150% in the 20% AFS scenario.

The focus of this research lies on fundamental research to provide guidelines for the design of new nanocatalyst toward improvement of the performance of proton exchange membrane fuel cells (PEMFCs). To achieve this overarching goal, several specific steps were taken with aims to: (1) provide guidelines for the design of new catalysts; (2) promote nanocatalyst applications towards alternative energy applications; and (3) integrate advanced instrumentation into nanocharacterization and fuel cell (FC) electrochemical behavior. In tandem with these goals, the cathode catalysts were extensively refined to improve the performance of PEMFCs and minimize noble metal usage. In this study, the major accomplishment was producing aligned carbon nanotubes (ACNTs), which were then modified by platinum (Pt) nanoparticles via a post-functionalization colloidal chemistry approach. The Pt-ACNTs demonstrated improved cathodic catalycity, by building better device endurance and decreased Pt loading. It was also determined that surface mechanical properties, such as elastic modulus and hardness were increased. Collectively, these enhancements provided an improved FC device. The electrochemical analyses indicated that the power density of the PEMFCs was increased to 900 mW/cm2 and current density to 3000 mA/cm2, respectively. The Pt loading was controlled at lower than 0.2 mg/cm2 to decrease the manufacturing expenses.

AbstractPreparation of uniform, spherical Li4Ti5O12 with high tap density is significant to achieve a high volumetric energy density in lithium‐ion batteries. Herein, Li4Ti5O12 microspheres with variable tap density and tunable size distribution were synthesized by a newly designed industrial spray‐drying approach. The slurry concentration, sintering time, sintering conditions after spraying, and the effect of lithium/titanium molar ratio on the lithium‐ion (Li+) storage capability were investigated. A narrow particle size distribution of around 10 μm and a high tap density close to 1.4 g cm−3 of the Li4Ti5O12 spheres can be obtained under the optimized conditions. The Li4Ti5O12 spheres can deliver a much higher capacity of 168 mAh g−1 at a rate of 1 C and show a high capacity retention of 97.7 % over 400 cycles. The synthetic conditions are confirmed to be critical for improving the electron conductivity and Li+ diffusivity by adjusting the crystal and spatial structures. As‐prepared high‐performance Li4Ti5O12 is an ideal electrode for lithium‐ion batteries or capacitors; meanwhile, the presented approach is also applicable for preparing other kind of spherical materials.

Abstract In this paper, the prevention of negative technogenic impact on the environment of oil sludge by using it as a secondary resource is considered. Oil sludge from various objects of oil fields in Kazakhstan (Mangystau region) has been studied. The possibilities of using oil (after its separation from oil sludge by bioremidiation) as a partial substitute for bitumen base in the production of modified bitumen are considered. The main physical and mechanical characteristics of modified bitumen are determined. The results confirm that the modified bitumen prepared with oil sludge and oil separated by bioremiation method meets the requirements for polymer-bitumen binder to Kazakhstan standards and is suitable for the production of modified bitumen in its physico-chemical characteristics.

The feasibility of rehabilitating an existing power house at the Enloe Dam in Washington was evaluated with consideration of expected power production, social and environmental impacts, regulatory aspects, technical requirements, financing, costs, and market potential. This assessment showed that rebuilding the existing powerhouse and appurtenant facilities is technically feasible. Rebuilding the existing turbines and generators proved to be the most desirable of three alternatives considered. The following four factors lead to this conclusion: rebuilding the old equipment is less costly than installing new turbines and generators; no major structural changes to the powerhouse would be required; rebuilding the turbines with increased flow capacity made the rebuilding alternative competitive with new equipment from an energy production standpoint; and rebuilding is compatible with the Enloe site's recent addition to the National Register of Historic Places.

The information and data contained in this Appendix was extracted from numerous sources. The principle sources used for technical data were Bonneville Power Administration's 1990 Resource Program along with its technical appendix, and Chapter 8 of the Draft 1991 Northwest Conservation and Electric Power Plan. All cost data is reported 1988 dollars unless otherwise noted. This information was supplemented by other data developed by Puget Sound utilities who participated on the Local Generation Team. Identifying generating resources available to the Puget Sound area involved a five step process: (1) listing all possible resources that might contribute power to the Puget Sound area, (2) characterizing the technology/resource status, cost and operating characteristics of these resources, (3) identifying exclusion criteria based on the needs of the overall Puget Sound Electric Reliability Plan study, (4) applying these criteria to the list of resources, and (5) summarizing of the costs and characteristics of the final list of resources. 15 refs., 20 tabs.