• Energy Research
• Closed Access close
• Restricted close
• Embargo close
• engineering and technology close

The present authors reply to the comment by Popov et al. (IEEE Trans. Power Del., vol.22, no.2, p.1261, April 2007) on the original paper by Ragavan and Satish (IEEE Trans. Power Del., vol.20, no.2, pt.1, p.780-8, April 2005)

Abstract In this work, energy analysis is carried out to account for inputs and outputs of energy and GHG emissions associated with the biodiesel production system. Jojoba oil is obtained by cultivation of the jojoba plant, harvesting of seeds followed by extraction of oil, which is then converted to biodiesel by the process of transesterification. Energy efficiency is expressed in terms of the net energy balance (NEB) and the net energy ratio (NER). The use of the byproducts (husk, cake or meal, waste residues and glycerin) are also included as a part of the system boundary. The results show that the NEB and NER values are calculated at 46724.1 MJ/ha (28.9 MJ/L biodiesel produced) and 2.16, respectively. At the same time, the total amount of GHG emissions are estimated at 2.28 kg-CO2eq/L biodiesel produced (66.0 g CO2eq/MJ biodiesel produced). Nevertheless, if manure is used as fertilizer for jojoba plant cultivation, the primary energy input will fall by 9.52% (to 22.49 MJ/L of biodiesel).

Reduced scale experiments are often employed in engineering because they are much cheaper than real scale testing. Unfortunately, though, it is difficult to design a thermal-hydraulic circuit or equipment in reduced scale capable of reproducing, both accurately and simultaneously, all the physical phenomena that occur in real scale and operating conditions. This paper presents a methodology to designing thermal-hydraulic experiments in reduced scale based on setting up a constrained optimization problem that is solved using genetic algorithms (GAs). In order to demonstrate the application of the methodology proposed, we performed some investigations in the design of a heater aimed to simulate the transport of heat and momentum in the core of a pressurized water reactor (PWR) at 100% of nominal power and non-accident operating conditions. The results obtained show that the proposed methodology is a promising approach for designing reduced scale experiments.

The diffusivity and solubility of fluorine in solid nickel were determined using the following solid-state electrochemical cells: Co + CoF2| BaF2| Ni | BaF2| Co + CoF2 Co + CoF2| CaF2| BaF2| Ni | BaF2| CaF2| Co + CoF2 In the temperature range 1023 to 1223 K, the diffusion coefficient of fluorine in solid nickel is given by: 1 $$D_F (cm^2 /s) = (2.13_{ - 1.54}^{ + 5.54} ) \times 10^{ - 3} \exp (( - 118,600 \pm 12,000J/mol)/RT)$$ The dissolution of atomic fluorine in solid nickel obeys Sieverts’ law; however, the solubility results showed considerable scatter. In the temperature range 1073 to 1223 K, the mean solubility of fluorine in solid nickel, corresponding to the equilibrium Ni + NiF2, follows the relationship: N -F S (at. pct) = 5.73 x 10-3 exp((10,850 J/mol)/RT)

Abstract The objective of this work is to evaluate the surge characteristics of an axial compressor operating under surge conditions, by using a hybrid BDF/harmonic balance method. During a surge event, a large amount of backflow occurs in the compressor. Consequently, the airflow oscillates along the axial direction at a low frequency, which can considerably damage the compressor. In this paper, a numerical investigation is performed to examine the effects of the system volume and average mass flow on the surge characteristics of a transonic high speed single stage axial compressor (stage 35) designed and evaluated at the NASA Glenn Center. The results show that the oscillation frequency of the airflow in the compressor generally ranges from 14.32–26.04 Hz during surge conditions, and both the system volume and average mass flow considerably influence the surge characteristics. For a constant average mass flow, as the system volume decreases, the oscillation frequency of the airflow in the compressor increases slightly, while the oscillation amplitude of the exit static pressure decreases significantly, and the maximum static pressure at the outlet remains nearly constant. In the case of a constant system volume, with the decrease in the average mass flow, the oscillation frequency of the airflow in the compressor gradually decreases, and the oscillation amplitude of the exit pressure increases significantly. With a further decrease in the average mass flow, the oscillation frequency stabilizes at a certain point and does not change thenceforth. Furthermore, the surge frequency obtained using the numerical method shows a same tendency with the Helmholtz frequency, but there is a considerable difference between them.

Abstract Flow behavior of particles in a two-dimensional spouted bed with a draft tube is studied using a continuous kinetic-friction stresses model. The kinetic stress of particles is predicted from kinetic theory of granular flow, while the friction stress is computed from a model proposed by Johnson et al. (1990) . A stitching function is used to smooth from the rapid shearing viscous regime to the slow shearing plastic regime. The distributions of concentration and velocities of particles are predicted in the spouted bed with a draft tube. Simulated results compare with the vertical velocity of particles ( Zhao et al., 2008 ) measured and in the spout bed with draft plates and solid circulation rate ( Ishikura et al., 2003 ) measured in the spouted bed with a draft tube. The impact of the friction stress of particles on the spout, annulus, fountain and entrancement regions is analyzed in gas–solid spouted bed with a draft tube. Numerical results show that the gas flow rate through the annulus increases with the increase of the entrainment zone. The solids circulation rate decreases with the decrease of inlet gas velocity and the height of the entrainment zone. The effect of spouting gas velocity on distributions of concentration, velocity and particle circulation is discussed.

Abstract In this paper, we present the use of different mathematical models to forecast electricity price under deregulated power. A successful prediction tool of electricity price can help both power producers and consumers plan their bidding strategies. Inspired by that the support vector regression (SVR) model, with the e -insensitive loss function, admits of the residual within the boundary values of e -tube, we propose a hybrid model that combines both SVR and Auto-regressive integrated moving average (ARIMA) models to take advantage of the unique strength of SVR and ARIMA models in nonlinear and linear modeling, which is called SVRARIMA. A nonlinear analysis of the time-series indicates the convenience of nonlinear modeling, the SVR is applied to capture the nonlinear patterns. ARIMA models have been successfully applied in solving the residuals regression estimation problems. The experimental results demonstrate that the model proposed outperforms the existing neural-network approaches, the traditional ARIMA models and other hybrid models based on the root mean square error and mean absolute percentage error.

Abstract Flow-accelerated corrosion (FAC) is a degradation mechanism that affects carbon steel piping in power plants. The failures and degradation due to FAC have necessitated numerous replacements in many power plants. Several computer codes around the world were developed as part of a systematic program or process to control FAC in power plant utilities. The typical plant model requires the input of the flow parameters, piping configuration and the plant water chemistry. The results on FAC rate are considered the key to proper selection of components for inspection. The lack of information on the effect of the upstream components located in the proximity limited the accuracy of the FAC prediction tools and hence will affect the accuracy in identifying potential inspection locations. In the present study 211 inspection data for 90° carbon steel elbows from several nuclear power plants were used to determine the effect of the proximity between two components on the FAC wear rate. The effect of the velocity as well as the distance between the elbows and the upstream components is discussed in the present analysis. Based on the analyzed trends obtained from the inspection data, significant increase in the wear rate of approximately 70% on average is identified to be due to the proximity.