• Energy Research
• Restricted close
• Embargo close
• engineering and technology close
• 13. Climate action close
• 2. Zero hunger close

Abstract This paper examines the effects of foreign trade and foreign direct investment (FDI) on CO 2 emissions in Turkey. We consider linear and nonlinear ARDL models and find significant asymmetric effects of exports, imports and FDI on CO 2 emissions per capita. However, FDI has no statistically significant long-run effects. In the long run, decreases in exports reduce CO 2 emissions per capita but increases in exports have no statistically significant effects. Increases in imports push up CO 2 emissions per capita, while decreases in imports have no long-run effects. On the other hand, CO 2 intensity, which measures CO 2 emissions per unit of energy, is not influenced by exports and imports, nor by FDI. Instead, it is affected positively by financial development and urbanization. Also, we find that an environmental Kuznets curve is present for both CO 2 measures so that increases in real GDP per capita have led to reductions in CO 2 emissions for at least the most recent decade, controlling for other confounding factors. Furthermore, the sectoral shares of CO 2 emissions in total CO 2 emissions change asymmetrically with foreign trade for two of four sectors, with export increases leading to lower CO 2 shares and imports having the opposite effect.

Two studies conducted in Guadeloupe (West Indies) and Réunion (Indian Ocean) islands were designed to investigate the benefits of producing sugarcane as an energy crop and to assess the influence of agroclimatic factors on energy efficiency, respectively. In this context, it is essential to know the low heating value of the dry above-ground biomass (LHVd, MJ/kg) and its energy yield (EY, MJ/m2) in order to select the best varieties and set up a payment method for growers. Eighteen Poaceae (sugarcane and Erianthus) cultivars were compared under wet tropical environmental conditions in Guadeloupe. Three sugarcane cultivars were studied in four contrasting environments in Réunion. The partition sampling and biomass measurement procedures were identical at both locations. Low heating value (LHV) predictions were achieved using near-infrared reflectance spectroscopy (NIRS) after specific calibration (Guadeloupe), or arithmetically after lignocellulosic compound prediction (Réunion). In both studies, LHV variability was very low and slightly dependent on the site, cultivar and above-ground biomass components (millable stalks and tops, and green and dead leaves). Considering the overall dry above-ground biomass (DAB, kg/m2), the LHVd was calculated by averaging 159 samples (mean 16.65 MJ/kg) in Guadeloupe and 315 samples (mean 16.45 MJ/kg) for Réunion. An excellent linear relationship between the DAB and its EY, regardless of cultivar, age and environment, was found (n = 474 and R² = 0.99). Sugarcane energy content assessment could thus be simplified by measuring the DAB, while enabling development of a faster method of payment for growers based on the DAB measurement and the correlation between DAB and EY. Finally, the findings of this study should allow growers to rapidly determine the commercial value of their sugarcane crops, and also enable purchasers to assess the amount of recoverable energy. (Résumé d'auteur)

The design and assessment of net-zero buildings commonly focus exclusively on the operational phase, ignoring the embodied environmental impacts over the building life cycle. An analysis is presented on the consequences of integrating embodied impacts into the assessment of the environmental advantageousness of net-zero concepts. Fundamental issues needing consideration in the design process - based on the evaluation of primary energy use and related greenhouse gas emissions - are examined by comparing three net-zero building design and assessment cases: (1) no embodied impacts included, net balance limited to the operation stage only; (2) embodied impacts included but evaluated separately from the operation stage; and (3) embodied impacts included with the operation stage in a life cycle approach. A review of recent developments in research, standardization activities and design practice and the presentation of a case study of a residential building in Norway highlight the critical importance of performance indicator definitions and system boundaries. A practical checklist is presented to guide the process of incorporating embodied impacts across the building life cycle phases in net-zero design. Its implications are considered on overall environmental impact assessment of buildings. Research and development challenges, as well as recommendations for designers and other stakeholders, are identified.

The building and construction sector is a large contributor to anthropogenic greenhouse gas emissions and consumes vast natural resources. Improvements in this sector are of fundamental importance for national and global targets to combat climate change. In this context, vertical greenery systems (VGS) in buildings have become popular in urban areas to restore green space in cities and be an adaptation strategy for challenges such as climate change. However, only a small amount of knowledge is available on the different VGS environmental impacts. This paper discusses a comparative life cycle assessment (LCA) between a building with green walls, a building with green facades and a reference building without any greenery system in the continental Mediterranean climate. This life cycle assessment is carried according to ISO 14040/44 using ReCiPe and GWP indicators. Moreover, this study fills this gap by thoroughly tracking and quantifying all impacts in all phases of the building life cycle related to the manufacturing and construction stage, maintenance, use stage (operational energy use experimentally tested), and final disposal. The adopted functional unit is the square meter of the facade. Results showed that the operational stage had the highest impact contributing by up to 90% of the total environmental impacts during its 50 years life cycle. Moreover, when considering VGS, there is an annual reduction of about 1% in the environmental burdens. However, in summer, the reduction is almost 50%. Finally, if the use stage is excluded, the manufacturing and the maintenance stage are the most significant contributors, especially in the green wall system.

It is well known that the efficiency of PV modules decreases with increasing module temperatures. Many studies have paid attention to the development and validation of heuristic models to calculate the PV module temperature in higher latitudes, however only a few focus on the thermal behaviour of PV modules in tropical regions of the world, where constantly high temperatures prevail. Also, little is known about the effect of including wind speed in these thermal models. This study evaluates three of such models - one that excludes wind, and two others including the wind influence - using hourly data for two tropical locations. Results show that the average hourly wind speeds in Singapore and Jayapura (Indonesia) are low and therefore the influence of the wind on the PV module temperature is minor. The three evaluated models produce about the same results with RMSE between 1.5-3.8 °C during daytime, which corresponds to a deviation in power output in the range of 0.3-1.6 %, depending on the PV module technology.

AbstractThe potential impacts of future climate scenarios on water balance and flow regime are presented and discussed for a temporary river system in southern Italy. Different climate projections for the future (2030–2059) and the recent conditions (1980–2009) were investigated. A hydrological model (Soil and Water Assessment Tool) was used to simulate water balance at the basin scale and streamflow in a number of river sections under various climate change scenarios, based on different combinations of global and regional models (global circulation models and regional climate models). The impact on water balance components was quantified at the basin and subbasin levels as deviation from the baseline (1980–2009), and the flow regime alteration under changing climate was estimated using a number of hydrological indicators. An increase in mean temperature for all months between 0.5–2.4 °C and a reduction in precipitation (by 4–7%) was predicted for the future. As a consequence, a decline of blue water (7–18%) and total water yield (11–28%) was estimated. Although the river type classification remains unvaried, the flow regime distinctly moves towards drier conditions and the divergence from the current status increases in future scenarios, especially for those reaches classified as I‐D (ie, intermittent‐dry) and E (ephemeral). Hydrological indicators showed a decrease in both high flow and low flow magnitudes for various time durations, an extension of the dry season and an exacerbation of extreme low flow conditions. A reduction of snowfall in the mountainous part of the basin and an increase in potential evapotranspiration was also estimated (4–4.4%). Finally, the paper analyses the implications of the climate change for river ecosystems and for River Basin Management Planning. The defined quantitative estimates of water balance alteration could support the identification of priorities that should be addressed in upcoming years to set water‐saving actions.

Saving energy in greenhouses is an important issue for growers. Here, we present a method to minimize the total energy that is required to heat and cool a greenhouse. Using this method, the grower can define bounds for temperature, humidity, CO2 concentration, and the maximum amount of CO2 available. Given these settings, optimal control techniques can be used to minimize energy input. To do this, an existing greenhouse climate model for temperature and humidity was expanded to include a CO2 balance. Heating, cooling, the amount of natural ventilation, and the injection of industrial CO2 were used as control variables.Standard optimization settings were defined in order to compare the grower's strategy with the optimal solution. This optimization resulted in a theoretical 47% reduction in heating, 15% reduction in cooling, and 10% reduction in CO2 injection for the year 2012. The optimal control does not need to maintain a minimum pipe temperature, in contrast to current practice. When the minimum pipe temperature strategy of the grower was implemented, heating and CO2 were reduced by 28% and 10% respectively.We also analyzed the effect of different bounds on optimal energy input. We found that as more freedom is given to the climate variables, the higher the potential energy savings. However, in practice the grower is in charge of defining the bounds. Thus, the potential energy savings critically depend on the choice of these bounds. This effect was analyzed by varying the bounds. However, because the effect can be demonstrated to the grower, the outcome has value to the grower with respect to decision making, an option that is not currently available in practice today.

<div class="section abstract"><div class="htmlview paragraph">The introduction of new light-duty vehicle emission limits to comply under real driving conditions (RDE) is pushing the diesel engine manufacturers to identify and improve the technologies and strategies for further emission reduction. The latest technology advancements on the after-treatment systems have permitted to achieve very low emission conformity factors over the RDE, and therefore, the biggest challenge of the diesel engine development is maintaining its competitiveness in the trade-off “CO₂-system cost” in comparison to other propulsion systems. In this regard, diesel engines can continue to play an important role, in the short-medium term, to enable cost-effective compliance of CO₂-fleet emission targets, either in conventional or hybrid propulsion systems configuration. This is especially true for large-size cars, SUVs and light commercial vehicles.</div><div class="htmlview paragraph">In this framework, a comprehensive approach covering the whole powertrain is of primary importance in order to simultaneously meet the performance, efficiency, noise and emission targets, and therefore, further development of the combustion system design and injection system represent important levers for additional improvements. For this purpose, a dedicated 0.5 dm³ single-cylinder engine has been developed and equipped with, a state-of-the-art Euro 6 combustion system, and an advanced common rail fuel injection system (FIS) offering higher flexibility in terms of injection strategy and higher quantity accuracy. Three injector nozzles with different hydraulic flow rates (HF) have been selected and employed for the overall combustion process optimization.</div><div class="htmlview paragraph">The optimization has been performed by means of an extensive DoE-based test campaign in which the engine and FIS operating parameters have been parametrized with the aim to carry out a proper combination in terms of HF and injection strategy. The results at partial load conditions evidence significant advantages in applying an advanced injection pattern, while the HF reduction can significantly improve the smoke emission and combustion noise without fuel consumption penalties. Therefore, a proper combination and optimization of the HF and injection strategy can provide low noise and engine-out smoke while maintaining the rated power performance targets.</div></div>