• Energy Research
• other engineering and technologies close

Abstract On the basis of experience acquired during a study on the reliability of PWR vessels, this text illustrates the points requiring more thorough investigation in order to raise the confidence level of the estimation of the reliability of the vessel. We also offer evidence of the need to develop, for already existing installations, adaptive type reliability models allowing a continually updated estimate of the reliability of the plant.

AbstractDecarbonising the energy system requires high shares of variable renewable generation and sector coupling like power to heat. In addition to heat supply, heat pumps can be used in future energy systems to provide flexibility to the electricity system by using the thermal storage potential of the building stock and buffer tanks to shift electricity demand to hours of high renewable electricity production. Bridging the gap between two methodological approaches, we coupled a detailed building technology operation model and the open-source energy system model Balmorel to evaluate the flexibility potential that decentral heat pumps can provide to the electricity system. Austria in the year 2030 serves as an example of a 100% renewable-based electricity system (at an annual national balance). Results show that system benefits from heat pump flexibility are relatively limited in extent and concentrated on short-term flexibility. Flexible heat pumps reduce system cost, CO2 emissions, and photovoltaics and wind curtailment in all scenarios. The amount of electricity shifted in the assessed standard flexibility scenario is 194 GWhel and accounts for about 20% of the available flexible heat pump electricity demand. A comparison of different modelling approaches and a deterministic sensitivity analysis of key input parameters complement the modelling. The most important input parameters impacting heat pump flexibility are the flexible capacity (determined by installed capacity and share of control), shifting time limitations, and cost assumptions for the flexibility provided. Heat pump flexibility contributes more to increasing low residual loads (up to 22% in the assessed scenarios) than decreasing residual load peaks. Wind power integration benefits more from heat pump flexibility than photovoltaics because of the temporal correlation between heat demand and wind generation.

In 1981 the Giprokhimmash suggested organizing the wide introduction of full secondary power source use at the Sumsk Severno industrial unit plants, including a considerable number of existing, under construction, and planned undertakings from various departments and services and predominantly the very large plants and production associations of Minkhimmash in the Sumsk Severuo industrial unit having large unused secondary power source reserves.

Abstract not Available.

One of the main uncertainties in long‐term distribution network planning is load forecasting error. This paper presents a probabilistic multistage expansion planning method to consider the load forecasting error as well as pseudo dynamic behavior of network parameters and geographical constraints. The optimal routes of MV feeders as backbone of distribution networks are obtained for both mid and long‐term case with deterministic and probabilistic modeling. The Imperialist Competitive Algorithm (ICA) is adapted for the optimal expansion planning of MV distribution network. To check and maintain the radial configuration of the MV distribution network during ICA random operators, a novel algorithm is employed. Comparative tabular and graphical results are given for deterministic and probabilistic planning. In probabilistic case the results is also represented by histogram of statistics data, mean and standard deviation of input and output variables using Monte Carlo Simulation (MCS). Based on the results it is possible to design the MV network at the presence of uncertainties more robust and flexible with respect to deterministic planning without reasonable increase in total cost. The efficiency and capability of the method is tested on a relatively large‐scale distribution network.

Abstract The accurate information of the thermal stresses and temperature in isotropic elastic solids is the key for many engineering applications. At present the classical linear coupled theory of thermoelasticity deduced with the assumptions of small temperature changes is widely used to solve the thermoelastic problems in engineering. In this paper, to describe the thermoelastic behavior in isotropic solids undergoing large temperature changes more accurately, the novel coupled models of thermoelasticity and the corresponding finite element models have been presented explicitly and validated by experimental measurement. The effect of large temperature changes on the solutions of thermoelastic problems is discussed. For the heat transfer process, if the isotropic elastic solids will expand when heated and contract when cooled and the condition d E E d T · σ i j E − δ i j 1 − 2 ν α 0 can be met in the context of small deformations, the effect of large temperature changes can be regarded as increasing the specific heat. The proposed models are applied to solve two thermoelastic problems. From the obtained numerical results, the effect of large temperature changes will increase with the amplitude of temperature change and may be considerably even when the temperature changes slowly.

To determine the potential impacts of micro-turbines on future distribution system, dynamic models of micro-turbines should be created, reduced in order, and scattered throughout test feeders. This paper presents the implementation of an efficient method for computing low order linear system models of micro-turbines from time domain simulations. The method is the Box-Jenkins algorithm for calculating the transfer function of a linear system from samples of its input and output.