• Energy Research
• Restricted close
• Embargo close
• other engineering and technologies close

Two studies conducted in Guadeloupe (West Indies) and Réunion (Indian Ocean) islands were designed to investigate the benefits of producing sugarcane as an energy crop and to assess the influence of agroclimatic factors on energy efficiency, respectively. In this context, it is essential to know the low heating value of the dry above-ground biomass (LHVd, MJ/kg) and its energy yield (EY, MJ/m2) in order to select the best varieties and set up a payment method for growers. Eighteen Poaceae (sugarcane and Erianthus) cultivars were compared under wet tropical environmental conditions in Guadeloupe. Three sugarcane cultivars were studied in four contrasting environments in Réunion. The partition sampling and biomass measurement procedures were identical at both locations. Low heating value (LHV) predictions were achieved using near-infrared reflectance spectroscopy (NIRS) after specific calibration (Guadeloupe), or arithmetically after lignocellulosic compound prediction (Réunion). In both studies, LHV variability was very low and slightly dependent on the site, cultivar and above-ground biomass components (millable stalks and tops, and green and dead leaves). Considering the overall dry above-ground biomass (DAB, kg/m2), the LHVd was calculated by averaging 159 samples (mean 16.65 MJ/kg) in Guadeloupe and 315 samples (mean 16.45 MJ/kg) for Réunion. An excellent linear relationship between the DAB and its EY, regardless of cultivar, age and environment, was found (n = 474 and R² = 0.99). Sugarcane energy content assessment could thus be simplified by measuring the DAB, while enabling development of a faster method of payment for growers based on the DAB measurement and the correlation between DAB and EY. Finally, the findings of this study should allow growers to rapidly determine the commercial value of their sugarcane crops, and also enable purchasers to assess the amount of recoverable energy. (Résumé d'auteur)

AbstractReview: 105 refs.

The design and assessment of net-zero buildings commonly focus exclusively on the operational phase, ignoring the embodied environmental impacts over the building life cycle. An analysis is presented on the consequences of integrating embodied impacts into the assessment of the environmental advantageousness of net-zero concepts. Fundamental issues needing consideration in the design process - based on the evaluation of primary energy use and related greenhouse gas emissions - are examined by comparing three net-zero building design and assessment cases: (1) no embodied impacts included, net balance limited to the operation stage only; (2) embodied impacts included but evaluated separately from the operation stage; and (3) embodied impacts included with the operation stage in a life cycle approach. A review of recent developments in research, standardization activities and design practice and the presentation of a case study of a residential building in Norway highlight the critical importance of performance indicator definitions and system boundaries. A practical checklist is presented to guide the process of incorporating embodied impacts across the building life cycle phases in net-zero design. Its implications are considered on overall environmental impact assessment of buildings. Research and development challenges, as well as recommendations for designers and other stakeholders, are identified.

The building and construction sector is a large contributor to anthropogenic greenhouse gas emissions and consumes vast natural resources. Improvements in this sector are of fundamental importance for national and global targets to combat climate change. In this context, vertical greenery systems (VGS) in buildings have become popular in urban areas to restore green space in cities and be an adaptation strategy for challenges such as climate change. However, only a small amount of knowledge is available on the different VGS environmental impacts. This paper discusses a comparative life cycle assessment (LCA) between a building with green walls, a building with green facades and a reference building without any greenery system in the continental Mediterranean climate. This life cycle assessment is carried according to ISO 14040/44 using ReCiPe and GWP indicators. Moreover, this study fills this gap by thoroughly tracking and quantifying all impacts in all phases of the building life cycle related to the manufacturing and construction stage, maintenance, use stage (operational energy use experimentally tested), and final disposal. The adopted functional unit is the square meter of the facade. Results showed that the operational stage had the highest impact contributing by up to 90% of the total environmental impacts during its 50 years life cycle. Moreover, when considering VGS, there is an annual reduction of about 1% in the environmental burdens. However, in summer, the reduction is almost 50%. Finally, if the use stage is excluded, the manufacturing and the maintenance stage are the most significant contributors, especially in the green wall system.

Operational intelligence in electric power systems is focused in a small number of control rooms that coordinate their actions. A clear division of responsibility and a command hierarchy organize system operation. With multi-agent based control systems, this control paradigm may be shifted to a more decentralized open-access collaboration control paradigm. This shift cannot happen at once, but must fit also with current operation principles. In order to establish a scalable and transparent system control architecture, organizing principles have to be identified that allow for a smooth transition. This paper presents a concept for the representation and organization of control- and resource-allocation, enabling computational reasoning and system awareness. The principles are discussed with respect to a recently proposed Subgrid operation concept.

The electrodissolution of p-Ge in aqueous NaOH solutions (pH 12-13) has been investigated with steady-state and impedance techniques. In the potential region where the process is under kinetic control, the impedance patterns are characterised by a high frequency capacitive loop, associated with the space charge, largely merged with another due to charge transfer resistance and double layer capacitance, and two low frequency loops changing from inductive to capacitive upon increasing the potential. At larger potential, under mixed control, the same high frequency features are observed, while a convection diffusion impedance dominates the low frequency response. The data relevant to pure kinetic control are interpreted with a simplified kinetic model, based on the classical scheme of Beck and Gerischer [Z. Electrochem., Ber. Bunsenges. Physik. Chem. 63 (1959) 500], neglecting transport effects and assuming only three electrochemical steps: (i) oxidation, involving water molecules, of Ge(0) to dihydroxylated Ge(II) by two holes; (ii) oxidation by one hole of Ge(II)-Ge(III) in a step requiring OH-; (iii) oxidative dissolution of Ge(III) proceeding either by hole capture or electron injection, leaving behind a surface Ge(0) species. Diagrams calculated for the limiting cases of pure depletion layer control reproduce the essential features of the experimental ones.

Thermoacoustic technology emerges as a sustainable and low-carbon method for energy conversion, leveraging environmentally friendly working mediums and independence from electricity. This study presents the development of a multimode heat-driven thermoacoustic system designed to utilize medium/low-grade heat sources for room-temperature cooling and heating. We constructed both a simulation model and an experimental prototype for a single-unit direct-coupled thermoacoustic system, exploring its performance in heating-only, cooling-only, and hybrid heating and cooling modes. Internal characteristic analysis including an examination of internal exergy loss and a distribution analysis of key parameters was first conducted in the hybrid cooling and heating mode. The results indicated a positive-focused traveling-wave-dominant acoustic field within the thermoacoustic core unit, enhancing energy conversion efficiency. The output system performance was subsequently tested under different working conditions in the heating-only and cooling-only modes. A maximum output heating power of 2.3 kW and a maximum COPh of 1.41 were observed in the heating-only mode. Meanwhile, a cooling power of 748 W and a COPc of 0.4 were obtained in the typical cooling condition at 7 °C when operating in cooling-only mode. These findings underscore the promising potential of thermoacoustic systems for efficiently utilizing medium/low-grade heat sources for cooling and/or heating applications in the future.

It is well known that the efficiency of PV modules decreases with increasing module temperatures. Many studies have paid attention to the development and validation of heuristic models to calculate the PV module temperature in higher latitudes, however only a few focus on the thermal behaviour of PV modules in tropical regions of the world, where constantly high temperatures prevail. Also, little is known about the effect of including wind speed in these thermal models. This study evaluates three of such models - one that excludes wind, and two others including the wind influence - using hourly data for two tropical locations. Results show that the average hourly wind speeds in Singapore and Jayapura (Indonesia) are low and therefore the influence of the wind on the PV module temperature is minor. The three evaluated models produce about the same results with RMSE between 1.5-3.8 °C during daytime, which corresponds to a deviation in power output in the range of 0.3-1.6 %, depending on the PV module technology.