• Energy Research
• other engineering and technologies close
• 7. Clean energy close
• 13. Climate action close
• 11. Sustainability close
• 2. Zero hunger close

Abstract In this work, energy analysis is carried out to account for inputs and outputs of energy and GHG emissions associated with the biodiesel production system. Jojoba oil is obtained by cultivation of the jojoba plant, harvesting of seeds followed by extraction of oil, which is then converted to biodiesel by the process of transesterification. Energy efficiency is expressed in terms of the net energy balance (NEB) and the net energy ratio (NER). The use of the byproducts (husk, cake or meal, waste residues and glycerin) are also included as a part of the system boundary. The results show that the NEB and NER values are calculated at 46724.1 MJ/ha (28.9 MJ/L biodiesel produced) and 2.16, respectively. At the same time, the total amount of GHG emissions are estimated at 2.28 kg-CO2eq/L biodiesel produced (66.0 g CO2eq/MJ biodiesel produced). Nevertheless, if manure is used as fertilizer for jojoba plant cultivation, the primary energy input will fall by 9.52% (to 22.49 MJ/L of biodiesel).

Reduced scale experiments are often employed in engineering because they are much cheaper than real scale testing. Unfortunately, though, it is difficult to design a thermal-hydraulic circuit or equipment in reduced scale capable of reproducing, both accurately and simultaneously, all the physical phenomena that occur in real scale and operating conditions. This paper presents a methodology to designing thermal-hydraulic experiments in reduced scale based on setting up a constrained optimization problem that is solved using genetic algorithms (GAs). In order to demonstrate the application of the methodology proposed, we performed some investigations in the design of a heater aimed to simulate the transport of heat and momentum in the core of a pressurized water reactor (PWR) at 100% of nominal power and non-accident operating conditions. The results obtained show that the proposed methodology is a promising approach for designing reduced scale experiments.

Short-term load forecasting is an essential instrument in power system planning, operation and control. Many operating decisions are based on load forecasts, such as dispatch scheduling of generating capacity, reliability analysis, and maintenance planning for the generators. Overestimation of electricity demand will cause a conservative operation, which leads to the start-up of too many units or excessive energy purchase, thereby supplying an unnecessary level of reserve. On the contrary, underestimation may result in a risky operation, with insufficient preparation of spinning reserve, causing the system to operate in a vulnerable region to the disturbance. In this paper, semi-parametric additive models are proposed to estimate the relationships between demand and the driver variables. Specifically, the inputs for these models are calendar variables, lagged actual demand observations and historical and forecast temperature traces for one or more sites in the target power system. In addition to point forecasts, prediction intervals are also estimated using a modified bootstrap method suitable for the complex seasonality seen in electricity demand data. The proposed methodology has been used to forecast the half-hourly electricity demand for up to seven days ahead for power systems in the Australian National Electricity Market. The performance of the methodology is validated via out-of-sample experiments with real data from the power system, as well as through on-site implementation by the system operator.

This paper examines and optimizes parameters that affect the air cooling of a Lithium-Ion (Li-Ion) battery, used in Electric Vehicles (EVs). A battery pack containing 150 cylindrical type Li-Ion battery cells in a PVC casing is investigated. An equal number of tubes are used in the pack as a medium to cool the battery by using a fan when the vehicle is stationary or with ambient air when in motion. The parameters affecting the air cooling of battery are studied and optimized by considering their practical constraints. The objective function and Number of Transfer Unit (NTU) are developed. Finally, a genetic algorithm method is employed to optimize the decision variables. Analysing the results shows that NTU can be maximized by increasing the diameter of tubes on the battery and keeping the air velocity in a certain range.

This paper investigates battery preheating before fast charging, for a battery electric vehicle (BEV) driving in a cold climate. To prevent the battery from performance degradation at low temperatures, a thermal management (TM) system has been considered, including a high-voltage coolant heater (HVCH) for the battery and cabin compartment heating. Accordingly, an optimal control problem (OCP) has been formulated in the form of a nonlinear program (NLP), aiming at minimising the total energy consumption of the battery. The main focus here is to develop a computationally efficient approach, mimicking the optimal preheating behavior without a noticeable increase in the total energy consumption. The proposed algorithm is simple enough to be implemented in a low-level electronic control unit of the vehicle, by eliminating the need for solving the full NLP in the cost of only 1Wh increase in the total energy consumption.

Abstract Flow-accelerated corrosion (FAC) is a degradation mechanism that affects carbon steel piping in power plants. The failures and degradation due to FAC have necessitated numerous replacements in many power plants. Several computer codes around the world were developed as part of a systematic program or process to control FAC in power plant utilities. The typical plant model requires the input of the flow parameters, piping configuration and the plant water chemistry. The results on FAC rate are considered the key to proper selection of components for inspection. The lack of information on the effect of the upstream components located in the proximity limited the accuracy of the FAC prediction tools and hence will affect the accuracy in identifying potential inspection locations. In the present study 211 inspection data for 90° carbon steel elbows from several nuclear power plants were used to determine the effect of the proximity between two components on the FAC wear rate. The effect of the velocity as well as the distance between the elbows and the upstream components is discussed in the present analysis. Based on the analyzed trends obtained from the inspection data, significant increase in the wear rate of approximately 70% on average is identified to be due to the proximity.

Abstract With promising benefits such as traffic emission reduction, traffic congestion alleviation, and parking problem solving, Electric Vehicle (EV)-sharing systems have attracted large attentions in recent years. Different from other business modes, customers in sharing economy systems are usually price sensitive. Therefore, it is possible to shift the usage of shared EVs through a well-designed Dynamic Pricing Scheme (DPS), with the objective of maximizing the system operator's total profit. In this study, we propose a novel DPS for a large-scale EV-sharing network to address the EV unbalancing issue and satisfy the vehicle-grid-integration (VGI) service based on accurate station-level demand prediction. The proposed DPS is formulated as a complex optimization problem, which includes two Price Adjustment Level (PAL) decision variables for every origin-destination pair of stations. The two PALs are employed to affect the EV-sharing demand and travel time between each station pair, respectively. Physical and operational constraints from both EV demand and VGI service aspects are also included in the proposed model. Two case study are conducted to validate the effectiveness of the proposed method.

The energy considered as waste heat in industrial furnaces owing to inefficiencies represents a substantial opportunity for recovery by means of thermal energy storage (TES) implementation. Although conventional systems based on sensible heat are used extensively, these systems involve technical limitations. Latent heat storage based on phase change materials (PCMs) results in a promising alternative for storing and recovering waste heat. Within this scope, the proposed PCM-TES allows for demonstrating its implementation feasibility in energy-intensive industries at high temperature range. The stored energy is meant to preheat the air temperature entering the furnace by using a PCM whose melting point is 885 °C. In this sense, a heat transfer model simulation is established to determine an appropriate design based on mass and energy conservation equations. The thermal performance is analysed for the melting and solidification processes, the phase transition and its influence on heat transference. Moreover, the temperature profile is illustrated for the PCM and combustion air stream. The obtained results prove the achievability of very high temperature levels (from 700 to 865 °C) in the combustion air preheating in a ceramic furnace; so corroborating an energy and environmental efficiency enhancement, compared to the initial condition presenting an air outlet at 650 °C.

The performance capabilities of an axially laminated anisotropic rotor (ALA) in a high-speed synchronous reluctance motor (SynRM) were studied. A 12 kW ALASynRM was designed as an alternative to a high-speed induction motor (IM) with a solid rotor. The electromagnetic design was implemented taking into account possible issues related to the new manufacturing methods, which require thicker rotor layers than in a typical ALA. The ALASynRM shows a higher efficiency than the corresponding IM with a smooth or slitted solid rotor equipped with copper end rings. To verify the design method, a prototype IM with a smooth solid rotor was built and tested. In the analysis, it was found that, similar to IMs, in an ALASynRM a considerable part of losses takes place in the rotor despite the absence of slip-related losses in the SynRM. The distribution of eddy current losses in the ALA rotor is significantly uneven. The torque ripple in the ALASynRM is considerably larger than the corresponding ripple in IMs.