• Energy Research

Nowadays, a car’s engine oil change interval is an essential factor in reducing wear. The correct choice depends on various factors. This study analyzes the changes in the composition of three different engine oils (0W30, 5W30, and 5W40) during the generally accepted oil change interval (15,000 km) in gasoline and diesel cars during the post-warranty period. Commercially available low-level biofuel blends (B7 and E10) were used to power test vehicles in a field test. Engine oil samples were taken every 3000 km for more detailed analysis and tested in an accredited laboratory. The contaminants in the engine oil were determined using several testing methods: spectrometric analysis, gas chromatography, etc. Studies have shown that all used cars have an increase in the number of iron particles, an increased concentration of silicon, and also an increase in the number of nickel particles above 12,000 km. Tests also showed a sharp drop of molybdenum anti-friction additives 4.5 times and a gradual increase in fuel concentration for the Opel Insignia over 12,000 km, but over 9000 km, a significant increase in the concentration of chromium particles. Based on this research results, it is preferable to choose a maintenance interval of no more than 12,000 km for cars during the post-warranty period. In this way, the intensity of engine wear can be reduced due to the loss of adequate protective properties of the engine oil.

Nowadays, a car’s engine oil change interval is an essential factor in reducing wear. The correct choice depends on various factors. This study analyzes the changes in the composition of three different engine oils (0W30, 5W30, and 5W40) during the generally accepted oil change interval (15,000 km) in gasoline and diesel cars during the post-warranty period. Commercially available low-level biofuel blends (B7 and E10) were used to power test vehicles in a field test. Engine oil samples were taken every 3000 km for more detailed analysis and tested in an accredited laboratory. The contaminants in the engine oil were determined using several testing methods: spectrometric analysis, gas chromatography, etc. Studies have shown that all used cars have an increase in the number of iron particles, an increased concentration of silicon, and also an increase in the number of nickel particles above 12,000 km. Tests also showed a sharp drop of molybdenum anti-friction additives 4.5 times and a gradual increase in fuel concentration for the Opel Insignia over 12,000 km, but over 9000 km, a significant increase in the concentration of chromium particles. Based on this research results, it is preferable to choose a maintenance interval of no more than 12,000 km for cars during the post-warranty period. In this way, the intensity of engine wear can be reduced due to the loss of adequate protective properties of the engine oil.

The analysis of biological resources for biofuels production in Ukraine has been carried out, and it has been shown that usage of alternative energy sources has great potential for substantially improving energy supply of the state and solving environmental problems. The directions of development and new technologies of obtaining motor fuels from biomass are systematized. It has been established that usage of different types of biofuels and their mixtures for feeding internal combustion engines involves application of modified engines in terms of structure and algorithms and usage of traditional designs of cars without significant structural changes. Moreover, the impact of biofuels on the efficient operation of the engine requires further integrated research.

The analysis of biological resources for biofuels production in Ukraine has been carried out, and it has been shown that usage of alternative energy sources has great potential for substantially improving energy supply of the state and solving environmental problems. The directions of development and new technologies of obtaining motor fuels from biomass are systematized. It has been established that usage of different types of biofuels and their mixtures for feeding internal combustion engines involves application of modified engines in terms of structure and algorithms and usage of traditional designs of cars without significant structural changes. Moreover, the impact of biofuels on the efficient operation of the engine requires further integrated research.

Biofuels are the most essential types of alternative fuels, which currently have significant potential to reduce CO2 emissions compared to fossil fuels. Methanol is a more efficient fuel than petrol due to its physicochemical properties, such as a higher latent heat of vaporization, research octane number, and heat of combustion of the fuel–air mixture. Also, biomethanol is cheaper than traditional petrol and diesel fuel for agricultural countries. The authors have proposed a new approach to improve the characteristics and efficiency of methanol diesel engines by using biomethanol mixed with hydrogen instead of pure biomethanol. Using a hydrogen–biomethanol mixture in modern engines is an effective method because hydrogen is a carbon-free, low-ignition, highest-flame-rate, high-octane fuel. A small quantity of hydrogen added to biomethanol and its combustion in an engine with a heat exchanger increases the combustion temperature and heat release, increases engine power, and reduces fuel consumption. This article presents experimental results of methanol combustion and a hydrogen-in-methanol mixture if hydrogen was retained due to the utilization of the heat of the exhaust gases. The tests were carried on a single-cylinder experimental engine with an injection of liquid methanol and gaseous hydrogen mixtures. The experiments showed that green hydrogen generated onboard the car due to the utilization of heat significantly reduced fuel costs of engines of vehicles and technological installations. It was established a hydrogen gaseous mixture addition of up to 5% by mass to methanol requires a corresponding change in the coefficient of excess air to λ = 1.25. Also, using an additional hydrogen mixture requires adjustment at the ignition moment in the direction of its decrease by 4–5 degrees of the engine crankshaft. Hydrogen gas mixture addition reduced methanol consumption, reaching a maximum reduction of 24%. The maximum increase in power was 30.5% based on experimental data. The reduction in the specified fuel consumption, obtained after experimental tests of the methanol research engine on the stand, can be implemented on the vehicle engines and technological installations equipped with an onboard heat recovery system. Such a system, due to the utilization of heat and the supply of additional hydrogen, can be implemented for engines that work on any alternative or traditional fuels.

Biofuels are the most essential types of alternative fuels, which currently have significant potential to reduce CO2 emissions compared to fossil fuels. Methanol is a more efficient fuel than petrol due to its physicochemical properties, such as a higher latent heat of vaporization, research octane number, and heat of combustion of the fuel–air mixture. Also, biomethanol is cheaper than traditional petrol and diesel fuel for agricultural countries. The authors have proposed a new approach to improve the characteristics and efficiency of methanol diesel engines by using biomethanol mixed with hydrogen instead of pure biomethanol. Using a hydrogen–biomethanol mixture in modern engines is an effective method because hydrogen is a carbon-free, low-ignition, highest-flame-rate, high-octane fuel. A small quantity of hydrogen added to biomethanol and its combustion in an engine with a heat exchanger increases the combustion temperature and heat release, increases engine power, and reduces fuel consumption. This article presents experimental results of methanol combustion and a hydrogen-in-methanol mixture if hydrogen was retained due to the utilization of the heat of the exhaust gases. The tests were carried on a single-cylinder experimental engine with an injection of liquid methanol and gaseous hydrogen mixtures. The experiments showed that green hydrogen generated onboard the car due to the utilization of heat significantly reduced fuel costs of engines of vehicles and technological installations. It was established a hydrogen gaseous mixture addition of up to 5% by mass to methanol requires a corresponding change in the coefficient of excess air to λ = 1.25. Also, using an additional hydrogen mixture requires adjustment at the ignition moment in the direction of its decrease by 4–5 degrees of the engine crankshaft. Hydrogen gas mixture addition reduced methanol consumption, reaching a maximum reduction of 24%. The maximum increase in power was 30.5% based on experimental data. The reduction in the specified fuel consumption, obtained after experimental tests of the methanol research engine on the stand, can be implemented on the vehicle engines and technological installations equipped with an onboard heat recovery system. Such a system, due to the utilization of heat and the supply of additional hydrogen, can be implemented for engines that work on any alternative or traditional fuels.