• Energy Research

In this paper, a numerical study is conducted to investigate the stress shadow effects (stress reorientation and change) during hydraulic fracturing in a transverse multiple fracture system. A numerical model is used for the numerical study. It is a 3D model and can simulate the fracture operation from injection begin to full closure (fracture contact). Therefore, there is no need to assume the fracture geometry for the investigation of the stress shadow effects (unlike previous studies). In the numerical study, the first and second operations in a fictive transverse multiple fracture system are simulated, meanwhile the stress shadow effects and their influences on the propagation and proppant placement of the second fracture are investigated. According to the results, the following conclusions are discerned: (1) most proppants are located in the lower part of the reservoir, even below the perforation; (2) the stress shadow effects are time-dependent and proppant dominated; (3) the stress shadow effects affect the fracture propagation and the proppant placement of the second fracture, and also the fracture conductivity of the first fracture; (4) the time-dependent stress shadow effects can be divided into four phases, fracture enlargement, closure without proppant contact, closure with proppant contact and full closure; and (5) the superposition effect of the stress shadow in a transverse multiple fracture system exists. According to the conclusions, some optimizations are recommended.

The utilization of geothermal energy can reduce CO2 emissions into the atmosphere. The reinjection of cooled return water from a geothermal field by a closed loop system is an important strategy for maintaining the reservoir pressure and prolonging the depletion of the geothermal reservoir by avoiding problems, e.g., water level drawdown, ground subsidence, and thermal pollution. However, the drawdown of water injectivity affected by physical and chemical clogging may occur in sandstone aquifers, and the reservoir temperature may be strongly affected by the reinjection of large amounts of cooled geothermal water, thus resulting in early thermal breakthrough at production wells and a decrease in production efficiency. In addition to the injection of cooled geothermal water, the injection of CO2 can be used to maintain the reservoir pressure and increase the injectivity of the reservoir by enhancing water–rock interactions. However, the thermal breakthrough and cooling effect of the geothermal reservoir may become complex when both CO2 and cooled geothermal water are injected into aquifers. In this paper, a simplified small-scale multilayered geological model is established based on a low-medium geothermal reservoir in Binhai district, Tianjin. The ECO2N module of the TOUGH2MP simulator is used to numerically simulate temperature and pressure responses in the geothermal reservoir while considering different treatment strategies (e.g., injection rates, temperatures, well locations, etc.). The simulation results show that a high injection pressure of CO2 greatly shortens the CO2 and thermal breakthrough at the production well. A much lower CO2 injection pressure is helpful for prolonging hot water production by maintaining the reservoir pressure and eliminating the cooling effect surrounding the production wells. Both pilot-scale and commercial-scale cooled water reinjection rates are considered. When the water production rate is low (2 kg/s), the temperature decrease at the production well is negligible at a distance of 500 m between two wells. However, when both the production and reinjection rates of cooled return water are increased to 100 m3/h, the temperature decrease in the production well exceeds 10 °C after 50 years of operation.

The emissions of greenhouse gases, especially CO2, have been identified as the main contributor for global warming and climate change. Carbon capture and storage (CCS) is considered to be the most promising strategy to mitigate the anthropogenic CO2 emissions. This review aims to provide the latest developments of CO2 storage from the perspective of improving safety and economics. The mechanisms and strategies of CO2 storage, focusing on their characteristics and current status, are discussed firstly. In the second section, the strategies for assessing and ensuring the security of CO2 storage operations, including the risks assessment approach and monitoring technology associated with CO2 storage, are outlined. In addition, the engineering methods to accelerate CO2 dissolution and mineral carbonation for fixing the mobile CO2 are also compared within the second section. The third part focuses on the strategies for improving economics of CO2 storage operations, namely enhanced industrial production with CO2 storage to generate additional profit, and co-injection of CO2 with impurities to reduce the cost. Moreover, the role of multiple CCS technologies and their distribution on the mitigation of CO2 emissions in the future are summarized. This review demonstrates that CO2 storage in depleted oil and gas reservoirs could play an important role in reducing CO2 emission in the near future and CO2 storage in saline aquifers may make the biggest contribution due to its huge storage capacity. Comparing the various available strategies, CO2-enhanced oil recovery (CO2-EOR) operations are supposed to play the most important role for CO2 mitigation in the next few years, followed by CO2-enhanced gas recovery (CO2-EGR). The direct mineralization of flue gas by coal fly ash and the pH swing mineralization would be the most promising technology for the mineral sequestration of CO2. Furthermore, by accelerating the deployment of CCS projects on large scale, the government can also play its role in reducing the CO2 emissions.

Although hydraulic fracturing has been massively studied and applied as a key technique to enhance the gas production from tight formations, some problems and uncertainties exist to accurately predict and analyze the fracture behavior in complex reservoirs, especially in the naturally fractured reservoirs like shale reservoirs. This paper presents a full 3D numerical model (FLAC3D) to study hydraulic fracturing behavior under the impact of preexisting orthogonal natural fractures. In this numerical model, the hydraulic fracture propagation direction is assumed perpendicular to the minimum principal stress and activated only by tensile failure, whereas the preexisting natural fractures can be activated by tensile or shear failure or a combination of them, and only tensile failure can open the natural fracture as well. The newly developed model was used to study the impact of preexisting orthogonal natural fractures on hydraulic fracturing behavior, based on a multistage hydraulic fracturing operation in a naturally fractured reservoir from the Barnett Shale formation, northwest of Texas in USA. In this multistage operation, two more representative stages, i.e., stage 1 with a relatively large horizontal stress anisotropy of 3.3 MPa and stage 4 with a comparatively small one of 1.3 MPa, were selected to conduct the simulation. Based on the numerical results, one can observe that the interaction between hydraulic and natural fracture is driven mainly by induced stress around fracture tip. Besides, the horizontal stress anisotropy plays a key role in opening the natural fracture. Thus, no significant opened fracture is activated on natural fracture in stage 1, while in stage 4 an opened fracture invades to about 90 m into the first natural fracture. Conversely, the hydraulic fracture length in stage 1 is much longer than in stage 4, as some fluid volume is stored in the opened natural fracture in stage 4. In this work, the shear failure on natural fractures is treated as the main factor for inducing the seismic events. And the simulated seismic events, i.e., shear failure on natural fractures, are very comparable with the measured seismic events.

The meaningful utilization of artificially created multiple fractures in tight formations is associated with the performance behavior of such flow channels, especially in the case of thermal energy extraction from sedimentary geothermal system. In this study, an innovative idea is presented to develop a numerical model for geothermal energy production based on concrete physical performance of an artificially created tensile multi-fracture system in a simplified manner. The state-of-the-art software FLAC3Dplus-TOUGH2MP-TMVOC are integrated to develop a coupled thermo-hydro-mechanical (THM) fictive model for constructing a multi-fracture scheme and estimating heat extraction performance. By incorporating the actual fracture width of newly created subsequent fracture under the effect of stress shadow, cubic law is implemented for fluid flow and geothermal energy production. The results depict that fracture spacing plays a vital role in the energy contribution through multiple fractures. Afterwards, a field case study to design huge multiple hydraulic fractures was performed in the geothermal well GB X1 in North Germany. The attenuation of fracture propagation becomes more significant when massive multiple fracturing operation is performed especially in the case of lower fracture spacing. The fictive model results will be extended to study the geothermal utilization of the North German basin through massive multiple fractures in our future work.