• Energy Research

In DIII-D, large currents flowing into the divertor floor during edge-localized modes (ELMs) have been measured by an array of shunt current resistors before an increase of heat flux is measured by IR thermography. The diagnostic consists of 40 tiles distributed in five concentric circles in the lower divertor with sampling rates range between 50 and 500 kHz. Typically, the current measured by a single tile during an ELM can reach 500 A. This amounts to 5–25 kA flowing in the divertor tiles. The temporal evolution of the ELM currents shows a first phase with large amplitude oscillations, occurring before the heat flux increase measured by infrared thermography at the same location, lasting between 0.05 ms and 0.3 ms. A second phase follows where the time evolution of the divertor current mimics the evolution of the divertor heat flux. These currents could affect the plasma edge stability in the nonlinear ELM phase and provide a mechanism leading to explosive growth of edge stochasticity, the need of which and existence is predicted in contemporary nonlinear ELM simulations.

In this paper we present initial simulations of pedestal control by Lithium Granule Injection (LGI) in NSTX. A model for small granule ablation has been implemented in the M3D-C1 code [1], allowing the simulation of realistic Lithium granule injections. 2D simulations in NSTX L-mode and H-mode plasmas are done and the effect of granule size, injection angle and velocity on the pedestal gradient increase are studied. For H-mode cases, the amplitude of the local pressure perturbation caused by the granules is highly dependent on the solid granule size. In our simulations, reducing the granule injection velocity allows one to inject more particles at the pedestal top.

Real-time lithium powder injection has been applied to long-pulse (>30 s) H-mode plasmas in EAST. This replenishes the active lithium surface that is routinely consumed by plasma-wall interactions. The real-time injection of Li powder into long H-mode discharges effectively suppresses impurity influx and controls recycling on EAST, with an ITER-like tungsten upper divertor. With lithium powder injection, the concentrations W, Mo, and C were reduced by 50% compared to ELMy H-mode discharges. During lithium injection, two effects play a role in the suppression of impurities influx: a reduced divertor temperature and heat flux and hence reduced erosion, and impurity trapping via deposition of a Li film onto plasma-facing surfaces. The ‘fresh’ injected lithium replenishes the film deposited during daily morning evaporation, restoring the wall's pumping capability. Thus, a measurable reduction in the global recycling coefficient was observed. Keyword: Long pulse plasma, Lithium, Impurity, Recycling

Collector probes have been used to examine tungsten divertor leakage in a variety of scenarios with low-Z impurity seeding during operation with the new tungsten-coated SAS-VW divertor in DIII-D. Measurements of tungsten deposition on collector probes inserted into the far Scrape-off-Layer (SOL) are used to deduce how efficiently tungsten leaks out of the closed, V-shaped divertor after it is eroded from the target surfaces. Qualitative differences in the tungsten deposition patterns across the collector probes provide clear experimental evidence that the SOL conditions depend on the low-Z impurity seeding conditions. These measurements show that in scenarios where neon gas is injected into the plasma, the tungsten divertor leakage and SOL transport depend on the poloidal location from which the neon is injected. In particular, neon injection from the Inner Midplane and Outer Midplane appear to each result in higher divertor leakage by a factor of 2 to 3 compared to cases with neon injection from either the SOL Crown or from the SAS-VW divertor itself.

Results from KSTAR powder injection experiments, in which tens of milligrams of boron nitride (BN) were dropped into low-power H-mode plasmas, show an improvement in wall conditions in subsequent discharges and, in some cases, a reduction or elimination of edge-localized modes (ELMs). Injected powder is distributed by the plasma flow and is deposited on the wall and, over the course of several discharges, was observed to gradually reduce recycling by 33%, and decrease both the ELM amplitude and frequency. This is the first demonstration of the use of BN for ELM mitigation. In all of these experiments, an Impurity Powder Dropper (IPD) was used to introduce precise, controllable amounts of the materials into ELMy H-mode KSTAR discharges. The plasma duration was between 10 s and 15 s, Ip=500 kA, BT=1.8 T, PNBI=1.6 MW, and PECH=0.6 MW. Plasma densities were between 2 and 3×1019 m−3. In all cases, the pre-fill and startup gas-fueling was kept constant, suggesting that the decrease in baseline Dαemission is in fact due to a reduction in recycling. The results presented herein highlight the viability of powder injection for intra-shot and between-shot wall conditioning.

DIII-D L-mode experiments with local boron powder injection for real-time wall conditioning have been interpreted for the first time with the 3D plasma edge transport Monte Carlo code EMC3-EIRENE. Local B sourcing in plasma scenarios with upstream densities 1.5 ⋅ 10^19 m −3 and 2.2 MW heating results in a nonaxisymmetric B distribution in the scrape-off layer (SOL) and on the divertor. The SOL frictional flows at high plasma density cause a strong inboard drag of injected impurities (≈ 90%), while lower background plasma densities tend to result in a more uniform distribution. The thermal forces prevent B deposition in the near SOL while the frictional force causes B fluxes to cover the divertor plasma-facing components in a region 7-10 cm beyond the strike line. Radiative dissipation occurs for B influxes above 1 ⋅ 10^20 s −1 and causes a moderate, non-axisymmetric reduction of the far SOL divertor heat fluxes. A comparison of top and midplane B injection shows no substantial difference in inboard vs. outboard asymmetries of the B distribution. On the other hand, erosion or recycling at the strike line may distribute the boron more uniformly in the SOL.

Injection of low-Z granules into high performance discharges on DIII-D has been shown to promptly trigger Edge Localized Modes (ELMs) providing high-Z impurity control without significant plasma degradation. The ability to provide ELM triggering over a range of injection and discharge parameters suggests that the mechanical introduction of granules can be considered as an additional method of impurity control in ITER. Utilizing a spherically symmetric vapor shielding model for granule ablation, benchmarked with impurity granule injections on DIII-D, we simulate the injection of beryllium granules into ITER baseline discharges. By comparing the granule induced ELM triggering size required for deuterium and non-fuel pellets on DIII-D and cross-correlating with a previously simulated JOREK calcuation of D pellet size required for ELM triggering in ITER, we estimate that a beryllium pellet of 1.5 mm diameter should provide reliable ELM triggering on ITER. This size pellet, delivered at 200 m/s should penetrate 3.5 cm past the separatrix, solidly within the H-mode steep gradient region, a location found to be advantageous for ELM triggering with minimal pellet size. Keywords: ELM pacing, granule injection, beryllium