• Energy Research

In this paper, we propose and investigate an original approach to energy conversion based on polyzwitterionic hydrogels, which exhibit an antipolyelectrolyte effect that enables them to swell in salt water and shrink in water of a different (i.e., desalinated water) salinity. The swelling and shrinking processes run cyclically and can move a piston up or down reversibly, thus transforming the antipolyelectrolyte effect into a mechanical force based on the salinity gradient. This phenomenon makes polyzwitterionic hydrogels suitable for use in a smart, polymeric engine. We apply this approach to investigate energy recovery from a polysulfobetaine-based hydrogel. The cross-linking density, external load, particle size, and repeatability of energy recoverability of hydrogels are examined. The maximum energy recovery from 0.4 g of hydrogel in feed (calculated based on dry form) of 102 mJ/kg was obtained by a hydrogel with a 3% cross-linking density, a 200-300 μm particle size, and 100 g external load. Excellent reproducibility of engine cycles was achieved over 10 cycles. This concept is complementary to the osmotic engine concept based on a polyelectrolyte hydrogel. In addition, polyzwitterionic materials have become a benchmark material for preventing biofouling, and the swelling properties of such materials can be further modulated and tuned.

In this study, we propose a new approach to attain energy by salinity gradient engines with pistons based on hydrogels possessing polyelectrolyte and antipolyelectrolyte effects in a tandem arrangement, providing energy in each salinity gradient mode in a repeatable manner. The swelling of hydrogel with a polyelectrolyte effect and shrinking of hydrogel particles possessing an antipolyelectrolyte effect in desalinated water, and subsequent shrinking of hydrogel with polyelectrolyte and swelling of hydrogel antipolyelectrolyte effect in saline water, generate power in both increasing and decreasing salinity modes. To investigate the energy recovery, we scrutinized osmotic engine assemblies by a setup arrangement of pistons with hydrogel particles, with polyelectrolyte and antipolyelectrolyte effects, in tandem. The energy recovery from the tandem engine setup (calculated based on dry form for each polyelectrolyte polyacrylate-based hydrogel-SPA) and antipolyelectrolyte–sulfobetaine-based gel with methacrylate polymeric backbone-SBE) up to 581 J kg−1 and a mean power of 0.16 W kg−1 was obtained by the tandem setup of SPA and SBE hydrogel containing 3% crosslinking density and particle size of 500 microns with an external load of 3.0 kPa. Exchange of sulfobetaine with methacrylamide (SBAm), the main polymer backbone, revealed a positive increase in energy recovery of 670 J kg−1 with a mean power of 0.19 W kg−1 for the tandem system operating under the same parameters (SPA@SBAm). The energy recovery can be controlled, modulated and tuned by selecting both hydrogels with antipolyelectrolyte and polyelectrolyte effects and their performing parameters. This proof of concept provides blue energy harvesting by contributing both polyelectrolyte and antipolyelectrolyte effects in a single tandem setup; together with easy accessibility (diaper-based materials (SPA)) and known antibiofouling, these properties offer a robust alternative for energy harvesting.

A robust microbial biosensor was constructed from a bionanocomposite prepared by a direct mixing of bacterial cells of Gluconobacter oxydans and carbon nanotubes with ferricyanide employed as a mediator for enhanced sensitivity of ethanol oxidation. A successful integration of the device into flow injection analysis mode of operation provided a high sensitivity of detection of (74 ± 2.7) μA mM(-1) cm(-2), a low detection limit of 5 μM and a linear range from 10 μM up to 1 mM. A short response time of the biosensor allowed a sample throughput of 67 h(-1) at 0.3 ml min(-1). The biosensor exhibited high operational stability with a decrease in the biosensor response of 1.7% during 43 h of continuous operation. The device was used to analyse ethanol in fermentation samples with a good agreement with a HPLC method.

A ferricyanide mediated microbial biosensor for ethanol detection was prepared by surface modification of a glassy carbon electrode. The selectivity of the whole Gluconobacter oxydans cell biosensor for ethanol determination was greatly enhanced by the size exclusion effect of a cellulose acetate (CA) membrane. The use of a CA membrane increased the ethanol to glucose sensitivity ratio by a factor of 58.2 and even the ethanol to glycerol sensitivity ratio by a factor of 7.5 compared with the use of a dialysis membrane. The biosensor provides rapid and sensitive detection of ethanol with a limit of detection of 0.85 microM (S/N=3). The selectivity of the biosensor toward alcohols was better compared to previously published enzyme biosensors based on alcohol oxidase or alcohol dehydrogenases. The biosensor was successfully used in an off-line monitoring of ethanol during batch fermentation by immobilized Saccharomyces cerevisiae cells with an initial glucose concentration of 200 g l(-1).

Although membrane-bound dehydrogenases isolated from Gluconobacter sp. (mainly PQQ-dependent alcohol and fructose dehydrogenase) have been used for preparing diverse forms of bioelectronic interfaces for almost 2 decades, it is not an easy task to interpret an electrochemical behaviour correctly. Recent discoveries regarding redox properties of membrane-bound dehydrogenases along with extensive investigations of direct electron transfer (DET) or direct bioelectrocatalysis with these enzymes are summarized in this review. The main aim of this review is to draw general conclusions about possible electronic coupling paths of these enzymes on various interfaces via direct electron transfer or direct bioelectrocatalysis. A short overview of the metabolism and respiration chain in Gluconobacter relevant to interfacial electrochemistry is given. Biosensor devices based on DET or direct bioelectrocatalysis using membrane-bound dehydrogenases from Gluconobacter sp. are described briefly with the emphasis given on practical applications of preparing enzymatic biofuel cells. Moreover, interfacial electrochemistry of Gluconobacter oxydans related to the construction of microbial biofuel cells is also discussed.

The present study is concerning the construction of ferricyanide-mediated Gluconobacter oxydans cell ethanol biosensor. The size exclusion effect of a cellulose acetate membrane was used for elimination of glucose interferences during ethanol assays in real samples. A typical response time of the biosensor was 13 s with a high sensitivity of 3.5 microA mM(-1). The microbial biosensor exhibits a very low detection limit of 0.85 microM and a wide linear range from 2 to 270 microM. The operational stability was excellent. During 8.5 h of repetitive ethanol assays, no decrease in the sensor sensitivity was observed. The biosensor was successfully used in the off-line monitoring of ethanol fermentation with a good agreement with HPLC measurements (R(2)=0.998).