• Energy Research

The traction substations of urban electric transport grids are oversized and underutilized in terms of their capacity. While their over-sizing is an unfortunate waste, their under-utilization creates the major hurdle for the integration of renewables into these grids due to the lack of a base load. Therefore, integrating smart grid loads such as EV chargers is not only an opportunity but a necessity for the sustainable transport grid of the future. This paper examines six methods for increasing the potential of EV chargers in three case studies of a trolleygrid, namely a higher substation no-load voltage, a higher substation power capacity, a smart charging method, adding a third overheard parallel line, adding a bilateral connection, and installing a multi-port converter between two substations. From the case studies, the most promising and cost-effective method seems to be introducing a bilateral connection, bringing a charging capacity for up to 175 electric cars per day. Meanwhile, other costly and complex methods, such as smart charging with grid state sensors and communication, can offer charging room for over 200 electric cars per day. Furthermore, using solar PV systems to power the grid showed a more than doubling of the directly utilized energy by installing a 150kW charger, from 19% to 41%. This reduces the power mismatch between the trolleygrid and the PV system from 81% to 59% and thereby reduces the severe economic need for storage, AC grid power exchange, or PV power curtailment while allowing a high penetration of renewables. DC systems, Energy conversion & Storage

In the presence of a catenary infrastructure, the transition from fossil fuel-based bus fleets to electric-powered ones can be facilitated through conventional trolleybuses or In-Motion-Charging trolleybuses, offering environmentally friendly and cost-effective solutions. However, grid congestion at traction substations (TSs) can limit this transition as the grid operator is incapable or unwilling to provide more capacity. As grid connection contracts are typically tallied and billed in periods of 15 minutes, stationary energy storage devices can prove useful in short-term buffering of the power demand. Consequently, more electrification projects can be rolled out under the same, or minimally extended grid contract. In this aim, this paper looks at validating energy storage as a means of enabling bus fleet electrification. It presents a power management strategy that controls the power exchange between the energy storage system (ESS) within the TS, specifically to manage the 15-minute average power. This strategy also serves as a tool for sizing the ESS with the minimum capacity required for the application. A case study for the city of Bologna, Italy, has been considered to validate the proposed approach. The findings indicate that billing contract power can be reduced by up to 41.7% when a storage device actuates in high-energy-demand substations. Furthermore, different types of Lithium-ion cells, including their second-life versions, are compared to determine the most beneficial options under limited cost and volume constraints. Recommendations are drawn on the exact scenarios where each type of cell is most beneficial.

This paper proposes a shared multi-stakeholder PV system for traction substations and nearby residential loads to reduce the need for storage, AC grid exchange, and curtailment. The residential stakeholders offer both the base electrical load and the solar panels installation space needed by the traction stakeholder, who brings the peak load and investments to the former. Two case studies were conducted for one year in the city of Arnhem, The cy=Netherlands, using comprehensive and verified simulation models: A high-traffic and a low-traffic substation. The results showed a positive, synergetic benefit in reducing the PV system's excess energy and size requirement for any type of traction substations connected to any number of households. In one detailed example, the multi-stakeholder system suggested in this paper is shown to reduce curtailment by up to 80% in moments of zero-traction load. Generally, the direct load coverage of a PV system is increased by as much as 7 absolute percentage points to the single-stakeholder system when looking at energy-neutral system sizes. This multi-stakeholders system offers then an increase in the techno-economic feasibility of PV system integration in urban loads. DC systems, Energy conversion & Storage

This paper offers a complete and verified model of DC trolleybus grids and examines the effect of the common modelling assumptions made in literature by using simulations, as well as bus and substation measurements from the grid of Arnhem, the Netherlands. An equivalent model for the overhead line impedance is offered taking into account the single line impedance, the supply and return lines, and the parallel connections between them. A case study shows that the feeder cables from the substations to the sections can be ignored, but only for certain substation power and feeder-line length ranges. On the other hand, the often-neglected regenerative braking, bus auxiliaries load, bilateral connections, and the exact nominal substation voltage are found to be crucial for the correct modelling of a trolleybus grid. Green Open Access added to TU Delft Institutional Repository 'You share, we take care!' - Taverne project https://www.openaccess.nl/en/you-share-we-take-care Otherwise as indicated in the copyright section: the publisher is the copyright holder of this work and the author uses the Dutch legislation to make this work public. DC systems, Energy conversion & Storage

Reducing the environmental impact of transportation requires the successful integration of renewable energy sources into the electrical transportation networks. However, the mismatch between renewable generation and the intermittent bus schedules causes temporary absence of loads and creates considerable excess energy, potentially rendering the systems economically infeasible. So far, studies on integration of renewables in transport grids were limited to decentralized solar PV systems (placed at the substation level), using statistical or simplified models, and concerned mainly with increasing the trolleygrid capacity. In this paper, both PV and Wind systems are considered and studied as to maximize their direct utilization by using verified simulation models for six different sizing and placement scenarios. The Dutch trolleygrid of Arnhem is used as a case study. Scenarios I to V looked at a decentralized renewable sources placement and ultimately concluded that PV systems at low-traffic substations are best sized for complete energy-neutrality, with daily storage systems. On the other hand, those at high-traffic substations should be without storage and sized below their energy-neutrality point — ideally, using the Marginal Utilization approach (scenario III). Finally, the Centralized (Aggregated) Energy-Neutral Wind and PV Approach of scenario VI offers the best outcome, with a hybrid solution of 53% PV and 47% Wind. This scenario offers a 54.1% direct bus load coverage. In comparison, scenario I, which had attempted a grid energy-neutrality in a decentralized manner, had only achieved 32.4% direct load coverage. The outcome of scenario VI can even be pushed to values above 80% by installing storage systems. DC systems, Energy conversion & Storage