• Energy Research

Emerging wide bandgap (WBG) semiconductors, such as silicon carbide (SiC), will enable chargers to operate at higher switching frequencies, which grants the ability to deliver high power and enhances efficiency. This paper addresses the modeling of a double-sided cooling (DSC) SiC technology-based off-board charger for battery electric buses (BEBs) and the design of its control and real-time (RT) implementation. A three-phase active front-end (AFE) rectifier topology is considered in the modeling and control system design for the active part of the DC off-board charger. The control system consists of a dual-loop voltage–current controller and is used to ensure AC to DC power conversion for charging and to achieve the targeted grid current total harmonic distortion (THD) and unity power factor (PF). Linear and nonlinear simulation models are developed in MATLAB/Simulink for optimum control design and to validate the voltage and current control performances. Four types of controllers (i.e., proportional–integral (PI), lead–lag, proportional–resonant (PR), and modified proportional–resonant (MPR)) are designed as current controllers, and a comparative analysis is conducted on the simulation model. In addition, the final design of the dual-loop controller is implemented on the RT–FPGA platform of dSpace MicroLabBox. It is then tested with the charger to validate the control performance with experimental data. The simulation and experimental results demonstrate the correct operation of the converter control performance by tracking the reference commands.

The development of electric vehicles (EVs) is an important step towards clean and green cities. An electric powertrain provides power to the vehicle and consists of a charger, a battery, an inverter, and a motor as the main components. Supplied by a battery pack, the automotive inverter manages the power of the motor. EVs require a highly efficient inverter, which satisfies low cost, size, and weight requirements. One approach to meeting these requirements is to use the new wide-bandgap (WBG) semiconductors, which are being widely investigated in the industry as an alternative to silicon switches. WBG devices have superior intrinsic properties, such as high thermal flux, of up to 120 W/cm2 (on average); junction temperature of 175–200 °C; blocking voltage limit of about 6.5 kV; switching frequency about 20-fold higher than that of Si; and up to 73% lower switching losses with a lower conduction voltage drop. This study presents a review of WBG-based inverter cooling systems to investigate trends in cooling techniques and changes associated with the use of WBG devices. The aim is to consider suitable cooling techniques for WBG inverters at different power levels.

Active Front-End (AFE) rectifiers have regained momentum as the demand for highpower Electric Vehicle (EV) charging infrastructure increases exponentially. AFE rectifiers have high efficiency and reliability, and they minimize the disturbances that could be generated due to the operation of the EV charging systems by reducing harmonic distortion and operating close to the Unity Power Factor (UPF). The purpose of this review is to present the current state-of-the-art AFE rectifiers used in fast chargers, focusing on the comparison between different AFE topologies and their components, as well as modular AFE solutions. Furthermore, different control strategies of AFE converters are presented and compared. Some of their more widely used control techniques, namely Voltage Oriented Control (VOC), Direct Power Control (DPC), Hysteresis Current Control (HCC), and Model Predictive Control (MPC), have been implemented, and their performance compared. Centralized and distributed control systems are compared for operating parallel AFE rectifiers for modular, fast charging systems. An overview of cooling systems and reliability evaluation tools is also presented. Finally, trends and future outlooks are analyzed.

Electric vehicles (EVs) are expected to take over the transportation and mobility market over traditional internal combustion engine (ICE) vehicles soon. The internal power demands of EVs are expected to increase. The reason for this is to achieve a longer driving range for the EV and to provide the required power for the low-voltage (LV) network auxiliary loads. To illustrate, there are extra added sensors, cameras, and small actuating motors, especially for future autonomous vehicles. Therefore, a new electrical/electronic (E/E) architecture is required to convert the high-voltage (HV) traction battery voltage (e.g., 320–800 V DC) to the standard LV levels with high current ratings of 5 kW and more. This HV-LV DC-DC converter is known in the literature as an auxiliary power module (APM). The standard LV rails in an EV are the 12 V/24 V rail to supply for an instant the EV’s lighting and electronic control units (ECUs), while the 48 V rail is required for propulsive loads, such as air compressors and electric power steering systems. Furthermore, in a few applications, this converter is responsible for voltage upwards to support the start of a hybrid vehicle or emergency backup power handling, which requires bidirectional capability. Therefore, in this paper, possible APM topologies for EV applications are presented. In line with this, the main standards and safety requirements of the APMs are presented. Detailed quantitative and qualitative comparisons between topologies and their associated control schemes are discussed. In addition, the placement of the APM in the EV cooling cycle has been investigated and demonstrated. Finally, the industrial trends and future research targets for the APM in automotive applications are outlined.