• Energy Research

In this paper we present a novel manufacturing method to produce achromatic Fresnel lenses for photovoltaic application. These achromatic lenses are capable of reaching a concentration factor three times higher than that attained by a conventional Silicone-on-Glass (SOG) Fresnel lens. The manufacturing method presented to fabricate the achromatic lens, which we refer to as Achromatic Doublet on Glass (ADG) Fresnel lens, is simple, cost-effective and highly scalable. A comprehensive ray-tracing analysis and its comparison with experimental results is presented in this work.

The 1-diode/2-resistors electric circuit equivalent to a photovoltaic system is analyzed. The equations at particular points of the I–V curve are studied considering the maximum number of terms. The maximum power point as a boundary condition is given special attention. A new analytical method is developed based on a reduced amount of information, consisting in the normal manufacturer data. Results indicate that this new method is faster than numerical methods and has similar (or better) accuracy than other existing methods, numerical or analytical.

Distributed solar photovoltaic (PV) systems are projected to be a key contributor to future energy landscape, but are often poorly represented in energy models due to their distributed nature. They have higher costs compared to utility PV, but offer additional advantages, e.g., in terms of social acceptance. Here, we model the European power network with a high spatial resolution of 181 nodes and a 2-hourly temporal resolution. We use a simplified model of distribution and transmission networks that allows the representation of power distribution losses and differentiates between utility and distributed generation and storage. Three scenarios, including a sector-coupled scenario with heating, transport, and industry are investigated. The results show that incorporating distributed solar PV leads to total system cost reduction in all scenarios (1.4% for power sector, 1.9-3.7% for sector-coupled). The achieved cost reductions primarily stem from demand peak reduction and lower distribution capacity requirements because of self-consumption from distributed solar. This also enhances self-sufficiency for countries. The role of distributed PV is noteworthy in the sector-coupled scenario and is helped by other distributed technologies including heat pumps and electric vehicle batteries.

This article summarizes experimental methods to evaluate the performance and to assess the efficiency of a lens that will be used as primary optics in a concentrating photovoltaic system comprising multijunction solar cells. The methods are classified into two groups: those intended to quantify the transmission losses and those that estimate the size and shape of the light spot. In addition, the optical efficiency definition is reviewed and a systematic procedure to evaluate it is proposed.

ABSTRACTThis paper proposes an indoor procedure based on charge‐coupled device camera measurements to characterize the non‐uniform light patterns produced by optical systems used in concentration photovoltaic (CPV) systems. These irradiance patterns are reproduced on CPV solar cells for their characterization at concentrated irradiances by using a concentrator cell tester and placing high‐resolution masks over the cells. Measured losses based on the masks method are compared with losses in concentrator optical systems measured by using the Helios 3198 solar simulator for CPV modules. Copyright © 2011 John Wiley & Sons, Ltd.

To achieve the ambitious climate goals of the Paris agreement [1] , major revisions of the global energy system are needed. Energy system modeling is, however, a complicated, task subject to large uncertainty [2]. Decision-makers have to consider a multitude of aspects including financial, political, and technical constraints. To aid decision-makers, energy system models are commonly used to study possible future scenarios [3].

To limit the global temperature increase to 1.5 degrees Celsius, fossil-free energy systems will be required eventually. To understand how such systems can be designed, the current state-of-the-art is to apply techno-economical optimisation modelling with high spatial and temporal resolution. This approach relies on a number of climatic, technical and economic predictions that reach multiple decades into the future. In this paper, we investigate how the design of a fossil-free energy system for Europe is affected by changes in these assumptions. In particular, the synergy among renewable generators, power-to-heat converters, storage units, synthetic gas and transmission manage to deliver an affordable net-zero emissions system. We find that levelised cost of energy decreases due to heat savings, but not for global temperature increases. In both cases, heat pumps become less favourable as surplus electricity is more abundant for heating. Demand-side management through buildings' thermal inertia could shape the heating demand, yet has modest impact on the system configuration. Cost reductions of heat pumps impact resistive heaters substantially, but not the opposite. Cheaper power-to-gas could lower the need for thermal energy storage. The submitted version, with 16 pages, 17 figures and 1 table