• Energy Research
• Closed Access close
• Restricted close
• Embargo close
• Energy close

Abstract A new formulation for the evaporation, flashing, condensation processes taking place in the effects of thermal desalination systems which simulates the operation of both forward and parallel/cross configurations is coupled with an exergo-economic model based on the SPECO method. The thermo-economic model uses accurate properties for the seawater, brine, pure water and vapour and is solved with an equation solver which does not require the development of a specific solution algorithm as in most previous studies. This flexible model is used to analyze the influence of the number of effects N and the temperature difference ΔT e between effects on the technical and economic performance of multi-effect desalination systems with ejector vapour compression. In particular, it is shown that the performance calculated by an earlier black-box approach is not attainable by technically and economically realistic systems. It is also shown that for each feed configuration and a given number of effects there exists an optimum value of ΔT e which minimizes the cost of the produced potable water. This last result forms the basis of a procedure that combines black-box results with the optimum value of ΔT e and can be used to select the appropriate system for any specific application.

Abstract A new formulation for the evaporation, flashing, condensation processes taking place in the effects of thermal desalination systems which simulates the operation of both forward and parallel/cross configurations is coupled with an exergo-economic model based on the SPECO method. The thermo-economic model uses accurate properties for the seawater, brine, pure water and vapour and is solved with an equation solver which does not require the development of a specific solution algorithm as in most previous studies. This flexible model is used to analyze the influence of the number of effects N and the temperature difference ΔT e between effects on the technical and economic performance of multi-effect desalination systems with ejector vapour compression. In particular, it is shown that the performance calculated by an earlier black-box approach is not attainable by technically and economically realistic systems. It is also shown that for each feed configuration and a given number of effects there exists an optimum value of ΔT e which minimizes the cost of the produced potable water. This last result forms the basis of a procedure that combines black-box results with the optimum value of ΔT e and can be used to select the appropriate system for any specific application.

Abstract Clamping mechanisms have significant effect on the performance of polymer electrolyte membrane (PEM) fuel cells. In this paper, PEM fuel cell with new clamping mechanism is designed to study the contact pressure distribution over the active area of PEM fuel cell's membrane electrode assembly (MEA). The clamping pressure is pneumatically exerted on the PEM fuel cell assembly. A comparison between the conventional and new clamping mechanism is carried out with simulation, and the numerical results are validated against experimental investigation performed in the fuel cell technology research laboratory. The experimental results are gathered using embedded pressure measurement films in the designed single cell. The results achieved via finite element method are in good agreement with experimental results. It is concluded that the contact pressure distribution of MEA for the new clamping mechanism is more uniform than the conventional one.

Abstract Clamping mechanisms have significant effect on the performance of polymer electrolyte membrane (PEM) fuel cells. In this paper, PEM fuel cell with new clamping mechanism is designed to study the contact pressure distribution over the active area of PEM fuel cell's membrane electrode assembly (MEA). The clamping pressure is pneumatically exerted on the PEM fuel cell assembly. A comparison between the conventional and new clamping mechanism is carried out with simulation, and the numerical results are validated against experimental investigation performed in the fuel cell technology research laboratory. The experimental results are gathered using embedded pressure measurement films in the designed single cell. The results achieved via finite element method are in good agreement with experimental results. It is concluded that the contact pressure distribution of MEA for the new clamping mechanism is more uniform than the conventional one.

Abstract The 2013/2017 Nankai Trough (Japan) and 2017 Shenhu Area (China) offshore methane hydrate production tests showed the world the possibility and feasibility of the oceanic methane hydrate production by depressurization. However, the relatively low gas production rate still remained as one of the critical bottlenecks for the economical utilization. This study chose the Nankai Trough as a target area, and aimed at the gas recovery enhancement from the methane hydrate reservoir using vertical wells. A traditional single-vertical-well system and a new dual-vertical-well system were proposed, and special production strategies of the aggressive depressurization and permeability improvement were applied to these two systems for the effectiveness verification. Based on the 15-year simulation results, it was found that the middle low-permeability silt-dominated layers in the reservoir held the key to the gas recovery enhancement, and for the single-vertical-well system, the permeability improvement in this sublayer seemed more reliable and feasible than the aggressive depressurization. On the other hand, the dual-vertical-well system significantly exceeded the single-vertical-well system due to the synergistic effect of the two wellbores, and could raise the average gas production rate (9.5 × 103 m3/day) by one order of magnitude (to 7.9 × 104 m3/day). Moreover, if this new system was combined with the aggressive depressurization, the average gas production rate could be further raised by one order of magnitude (to 3.4 × 105 m3/day).

Abstract The 2013/2017 Nankai Trough (Japan) and 2017 Shenhu Area (China) offshore methane hydrate production tests showed the world the possibility and feasibility of the oceanic methane hydrate production by depressurization. However, the relatively low gas production rate still remained as one of the critical bottlenecks for the economical utilization. This study chose the Nankai Trough as a target area, and aimed at the gas recovery enhancement from the methane hydrate reservoir using vertical wells. A traditional single-vertical-well system and a new dual-vertical-well system were proposed, and special production strategies of the aggressive depressurization and permeability improvement were applied to these two systems for the effectiveness verification. Based on the 15-year simulation results, it was found that the middle low-permeability silt-dominated layers in the reservoir held the key to the gas recovery enhancement, and for the single-vertical-well system, the permeability improvement in this sublayer seemed more reliable and feasible than the aggressive depressurization. On the other hand, the dual-vertical-well system significantly exceeded the single-vertical-well system due to the synergistic effect of the two wellbores, and could raise the average gas production rate (9.5 × 103 m3/day) by one order of magnitude (to 7.9 × 104 m3/day). Moreover, if this new system was combined with the aggressive depressurization, the average gas production rate could be further raised by one order of magnitude (to 3.4 × 105 m3/day).

An expression for the optimum length of a flat-plate solar collector that maximizes the life-cycle savings of the collector is derived. An expression has been obtained also for the optimal distribution of a finite amount of thermal insulation that minimizes the energy loss from the back side of a flat-plate solar collector.

An expression for the optimum length of a flat-plate solar collector that maximizes the life-cycle savings of the collector is derived. An expression has been obtained also for the optimal distribution of a finite amount of thermal insulation that minimizes the energy loss from the back side of a flat-plate solar collector.

Abstract Process heaters are typically located outside and subject to the weather. Although heaters are typically tuned at a given set of conditions, actual operating conditions vary significantly from season to season and sometimes even within a given day. Unfortunately, most heaters are not properly adjusted for actual operating conditions. Ambient air temperature, pressure and humidity all significantly impact process heater efficiency. This paper shows how changing ambient conditions can reduce efficiency if proper adjustments are not made. Combustion efficiency is related to air:fuel ratio and to air–fuel mixing. A general industry rule-of-thumb is that operating at 2–3% excess O 2 (dry basis) results in the best combination of efficiency and flexibility. At higher O 2 levels, efficiency is reduced because the additional O 2 and N 2 absorb heat, much of which exits the exhaust stack. At lower O 2 levels, efficiency can be substantially reduced because some fuel is uncombusted. Low O 2 levels can also lead to soot and coke buildup on process tubes reducing heat transfer to the process fluid and reducing efficiency. Several examples demonstrate how ambient conditions affect heater efficiency. Calculations and graphs for a wide range of operating conditions demonstrate how efficiency can be affected by changes in ambient conditions for process heaters.