• Energy Research
• Open Access close
• Hyper Article en Ligne close

This paper addresses the study of vibrations induced by turbulent boundary layers (TBLs) flowing over plate-like structures. The aim is here to propose a predictive method in order to evaluate the vibroacoustical behaviour of a plate excited by TBL pressure fluctuations. The ultimate goal is to develop tools for predicting internal cabin noise in an aircraft during flight. Hence TBL is considered. Different TBL models are discussed and compared. A prediction method well suited for mid-high frequencies is also presented. The method called simplified energy method (SEM) is based on local energetic considerations and extends the well-known statistical energy analysis (SEA). Two different SEM formulations are presented. The first one is of heat conduction type, whilst the second is radiative. The TBL source model was integrated in the local energy proposed formulations. When applied to a simple Kirchhoff-Love simply supported plate, SEM allows prediction of averaged energy quantities. Comparisons are drawn between heat and radiative formulations. Good concordance was observed between energy results and pure analytical calculations of the structural response under TBL excitation over a wide frequency range.

This paper addresses the study of vibrations induced by turbulent boundary layers (TBLs) flowing over plate-like structures. The aim is here to propose a predictive method in order to evaluate the vibroacoustical behaviour of a plate excited by TBL pressure fluctuations. The ultimate goal is to develop tools for predicting internal cabin noise in an aircraft during flight. Hence TBL is considered. Different TBL models are discussed and compared. A prediction method well suited for mid-high frequencies is also presented. The method called simplified energy method (SEM) is based on local energetic considerations and extends the well-known statistical energy analysis (SEA). Two different SEM formulations are presented. The first one is of heat conduction type, whilst the second is radiative. The TBL source model was integrated in the local energy proposed formulations. When applied to a simple Kirchhoff-Love simply supported plate, SEM allows prediction of averaged energy quantities. Comparisons are drawn between heat and radiative formulations. Good concordance was observed between energy results and pure analytical calculations of the structural response under TBL excitation over a wide frequency range.

Cu(In,Ga)Se-2-based solar cells buffered with indium sulfide grown by numerous techniques have reached efficiencies comparable to those achieved by standard devices buffered with (CBD)CdS. The present paper firstly recalls some of the properties of the indium sulfide single crystal and Points Out the disagreements concerning the thin films properties inventoried in the literature. Secondly, the influence of the presence of some "foreign elements" within file indium sulfide on its properties is presented. It is shown that these "foreign elements", even at low concentration levels, are possibly at the origin or the thin films properties deviations compared to the single crystal. The impact of these contaminants on the solar cells performance is finally discussed.

Cu(In,Ga)Se-2-based solar cells buffered with indium sulfide grown by numerous techniques have reached efficiencies comparable to those achieved by standard devices buffered with (CBD)CdS. The present paper firstly recalls some of the properties of the indium sulfide single crystal and Points Out the disagreements concerning the thin films properties inventoried in the literature. Secondly, the influence of the presence of some "foreign elements" within file indium sulfide on its properties is presented. It is shown that these "foreign elements", even at low concentration levels, are possibly at the origin or the thin films properties deviations compared to the single crystal. The impact of these contaminants on the solar cells performance is finally discussed.

The movement of the powdery material occurs in a multi-phase non-uniform electrostatic field at determined values of the voltage and the frequency, using travelling wave technique. This technique was applied for very small particles such as bacteria and other similar particle size. The objective of this work is to analyze the movement of PVC micronized particles and the feasibility of the separation of PVC/copper granular mixture of average size 100 μm. Two-phase and three-phase conveyors, which are supplied by high voltage amplifiers controlled by digital function generators, have been the subject of a parametric experimental investigation. Several factors were analyzed such as the voltage level up to 1400 V, the frequency, the phase shift and the number of phases of the conveyor. The obtained results showed that depending on the values of the above factors: i) the micronized particles can move instantly right after switching the conveyor, ii) the particles move towards one direction or the other of the conveyor iii) the separation of a granular mixture of plastic and copper micronized particles is possible.

The movement of the powdery material occurs in a multi-phase non-uniform electrostatic field at determined values of the voltage and the frequency, using travelling wave technique. This technique was applied for very small particles such as bacteria and other similar particle size. The objective of this work is to analyze the movement of PVC micronized particles and the feasibility of the separation of PVC/copper granular mixture of average size 100 μm. Two-phase and three-phase conveyors, which are supplied by high voltage amplifiers controlled by digital function generators, have been the subject of a parametric experimental investigation. Several factors were analyzed such as the voltage level up to 1400 V, the frequency, the phase shift and the number of phases of the conveyor. The obtained results showed that depending on the values of the above factors: i) the micronized particles can move instantly right after switching the conveyor, ii) the particles move towards one direction or the other of the conveyor iii) the separation of a granular mixture of plastic and copper micronized particles is possible.

A natural holm oak forest was selectively thinned to test thinning as a tool to reduce tree mortality, increase productivity, and reverse the recent regression of the dominant species (Quercus ilex) induced by climate change. Thinning increased aboveground productivity and reduced stem mortality in this Mediterranean forest during four years just after thinning, contributing to the maintenance of forest functioning under changing climatic conditions. Q. ilex was the only species positively affected by the thinning: stem growth increased for all stem sizes, and mortality was significantly lower in thinned plots. On the contrary, mortality rates of Phillyrea latifolia and Arbutus unedo were not significantly lower. Stem growth increased for P. latifolia only in the smallest stem-size class. Our results highlight the suitability of selective thinning for improving the forest productivity and ensuring the conservation of Mediterranean coppices. Other benefits of selective thinning, such as a decrease in the risk of fire dispersion and an increase in the water supply for human populations, are also discussed.