• Energy Research
• Closed Access close

Wide‐bandgap (WBG) perovskite solar cells (PSCs) are acknowledged as promising candidates for tandem solar cells and building photovoltaics. It is well known that cesium‐based all‐inorganic halide WBG perovskites possess the comparable optoelectronic properties as the organic–inorganic counterparts, but exhibit superior thermal stability. Among them, CsPbIBr2 is considered a feasible material for tandem solar cells after balancing the bandgap and stability of the inorganic perovskite. However, CsPbIBr2 PSCs are often subjected to drastic interfacial charge recombination especially in carbon‐based device structure derived from the chemical bonding defects (i.e., uncoordinated Pb2+) naked on CsPbIBr2 soft lattice, which dramatically limits overall efficiency of CsPbIBr2 WBG PSCs. Herein, a trimethyl ammonium salt hexyltrimethylammonium bromide is presented for CsPbIBr2/carbon interfacial modification. Benefiting from the −N+(CH3)3 passivation effect and −C6H13 hydrophobic alkyl chain, the optimal device with highly smooth morphology and sufficient charge extraction exhibits a champion power conversion efficiency of 11.24% and improved long‐term stability with 99.7% and 79.7% efficiency retention under dry air atmosphere and continuous 85 °C thermal stress, indicating the valuable potential application of the lattice solidified CsPbIBr2 WBG PSCs.

A method is presented for calculating the electromagnetic forces on the end windings of turbine generators for both the steady state and transient modes of operation. Part 1 of this paper deals with the basic concepts of the force calculation and gives several examples of steady state forces and how they vary with load and power factor. PartII deals with several types of transient operation. The currents and fields which these transients produce are discussed and forces are found for various cases such as short circuits, synchronizing out of phase and transmission line switching.

The article deals with studies of the arcing performance of SF6 puffer breakers at currents of up to 80 kA and voltages of up to 200 kV, using an interrupter unit fitted with viewing windows. The studies are mainly concerned with the behavior of the arc at current zero and with restrike phenomena under various conditions. In addition to measurements of the electrical variables and the pressure variation, the tests cover the use of high-speed cameras, spectroscopic diagnostic methods, and schlieren methods. The density fields and flow fields derived from the latter are used to optimize the gas flow. On the basis of the breaker data and those of its operating mechanism a method for computing the essential variables, e.g., pressure, gas flow, back pressure, and contact travel, is developed. The variation of these parameters as a function of the interrupter data for various currents and with due allowance for the interaction between the arc and the operating mechanism must be known if the breaker design is to be optimized. The method uses simplified equations for the gas flow and the arc. The relationship between the gas data (e. g., density, enthalpy, speed of sound, electrical conductivity, and dielectric strength) and the temperature is taken into account by using approximation functions. The temperature of the arc core is matched to the test results.

The microbial electrolysis desalination and chemical-production cell (MEDCC) is a device to desalinate seawater, and produce acid and alkali. The objective of this study was to enhance the desalination and chemical-production performance of the MEDCC using two types of stack structure. Experiments were conducted with different membrane spacings, numbers of desalination chambers and applied voltages. Results showed that the stack construction in the MEDCC enhanced the desalination and chemical-production rates. The maximal desalination rate of 0.58 ± 0.02 mmol/h, which was 43% higher than that in the MEDCC, was achieved in the four-desalination-chamber MEDCC with the AEM-CEM stack structure and the membrane spacing of 1.5mm. The maximal acid- and alkali-production rates of 0.079 ± 0.006 and 0.13 ± 0.02 mmol/h, which were 46% and 8% higher than that in the MEDCC, respectively, were achieved in the two-desalination-chamber MEDCC with the BPM-AEM-CEM stack structure and the membrane spacing of 3mm.