• Energy Research
• Restricted close
• 13. Climate action close
• 11. Sustainability close
• 15. Life on land close
• 14. Life underwater close

Abstract The aerodynamic design of small wind turbines for the urban setting attracts increasing interest within the scientific community, but the adoption of a proper control strategy may be just as important, especially in high turbulent winds, where such energy conversion devices should ideally operate. As a matter of fact, the mere rotor efficiency is meaningless unless the system has also the capability of rapidly changing its angular speed in case of a sudden variation of the wind velocity, to reach a new optimal operating condition. This work will attempt neither to develop dynamic simulation models nor to examine possible turbine control strategies, being the focus much broader, namely, the investigation of operational contexts where the peculiar inertial characteristics of wind turbines would compromise any form of robust control. Inertial and operational data of commercially available turbines (characterized by both horizontal and vertical-axis architectures), as well as the results disseminated in various literature sources, operational experiences and design best practices, are here collected under one cover and compared, thus deriving some basic and fundamental relations between rotor inertia and angular acceleration, highlighting how, in several cases, a control strategy based on the continuous tracking of the optimal operating condition is most unlikely. Such considerations raise the question of whether the problem of inertia renders futile many prevailing theories about small wind turbine operation and plans for implementing new control strategies, especially as far as vertical axis architectures are concerned. On the other hand, some constructive advice is also presented, in the form of a means to compare the effective performances of different turbines, in a given installation site, with respect to their nominal (i.e. steady state, or wind tunnel) behaviour. As a final result, a new bound for a reliable estimation of the amount of energy a wind turbine will generate in a specific site is suggested, based on the comparison between a representative time scale of the installation site and the response time of the candidate wind turbine.

Saving energy in greenhouses is an important issue for growers. Here, we present a method to minimize the total energy that is required to heat and cool a greenhouse. Using this method, the grower can define bounds for temperature, humidity, CO2 concentration, and the maximum amount of CO2 available. Given these settings, optimal control techniques can be used to minimize energy input. To do this, an existing greenhouse climate model for temperature and humidity was expanded to include a CO2 balance. Heating, cooling, the amount of natural ventilation, and the injection of industrial CO2 were used as control variables.Standard optimization settings were defined in order to compare the grower's strategy with the optimal solution. This optimization resulted in a theoretical 47% reduction in heating, 15% reduction in cooling, and 10% reduction in CO2 injection for the year 2012. The optimal control does not need to maintain a minimum pipe temperature, in contrast to current practice. When the minimum pipe temperature strategy of the grower was implemented, heating and CO2 were reduced by 28% and 10% respectively.We also analyzed the effect of different bounds on optimal energy input. We found that as more freedom is given to the climate variables, the higher the potential energy savings. However, in practice the grower is in charge of defining the bounds. Thus, the potential energy savings critically depend on the choice of these bounds. This effect was analyzed by varying the bounds. However, because the effect can be demonstrated to the grower, the outcome has value to the grower with respect to decision making, an option that is not currently available in practice today.

<div class="section abstract"><div class="htmlview paragraph">The introduction of new light-duty vehicle emission limits to comply under real driving conditions (RDE) is pushing the diesel engine manufacturers to identify and improve the technologies and strategies for further emission reduction. The latest technology advancements on the after-treatment systems have permitted to achieve very low emission conformity factors over the RDE, and therefore, the biggest challenge of the diesel engine development is maintaining its competitiveness in the trade-off “CO₂-system cost” in comparison to other propulsion systems. In this regard, diesel engines can continue to play an important role, in the short-medium term, to enable cost-effective compliance of CO₂-fleet emission targets, either in conventional or hybrid propulsion systems configuration. This is especially true for large-size cars, SUVs and light commercial vehicles.</div><div class="htmlview paragraph">In this framework, a comprehensive approach covering the whole powertrain is of primary importance in order to simultaneously meet the performance, efficiency, noise and emission targets, and therefore, further development of the combustion system design and injection system represent important levers for additional improvements. For this purpose, a dedicated 0.5 dm³ single-cylinder engine has been developed and equipped with, a state-of-the-art Euro 6 combustion system, and an advanced common rail fuel injection system (FIS) offering higher flexibility in terms of injection strategy and higher quantity accuracy. Three injector nozzles with different hydraulic flow rates (HF) have been selected and employed for the overall combustion process optimization.</div><div class="htmlview paragraph">The optimization has been performed by means of an extensive DoE-based test campaign in which the engine and FIS operating parameters have been parametrized with the aim to carry out a proper combination in terms of HF and injection strategy. The results at partial load conditions evidence significant advantages in applying an advanced injection pattern, while the HF reduction can significantly improve the smoke emission and combustion noise without fuel consumption penalties. Therefore, a proper combination and optimization of the HF and injection strategy can provide low noise and engine-out smoke while maintaining the rated power performance targets.</div></div>

A Life Cycle Assessment (LCA) with focus on carbon footprint, followed by Life Cycle Costing (LCC) of municipal solid waste (MSW) management were conducted in a residential area of a medium-sized European city of 80,000 inhabitants. The initial results showed high environmental impacts and lack of economic sustainability, due to the high amounts of waste landfilled, the low extent of separate collection, low performance of mechanical-biological treatment as well as absence from alternatives to landfilling of non-recyclable materials. Taking this result as a baseline scenario, three improvement.s were tested with the aim of turning the carbon footprint of the local MSW management system into a neutral value: (i) increased separate collection of recyclables, (ii) enhanced biogas production and (iii) refuse-derived fuel (RDF) production. Successively adding the improvements, three alternative improved scenarios were defined, until reaching a negative carbon footprint, meaning that an optimised system would avoid GHG emissions. The proposed changes were sufficient to achieve carbon neutrality, as well as reduce overall environmental impacts, but were not enough for achieving economic sustainability due to the great influence of collection costs, especially for separate collection. It was concluded that by using an adequate combination of several treatment options and increasing the separate collection of recyclable materials it is possible to turn MSW management into a carbon neutral activity as well as improve its economic balance.

In Vietnam, the energy demand shows an ever-increasing trend. To limit the utilization of fossil fuels and the following consequences for the environment, renewable energy sources must be adopted. In this context, the paper assesses the utilization of offshore wind and sea wave, by considering a commercial wind turbine and a prototypical wave energy converter. Solar energy can be optionally also collected by this device. An algorithm is introduced to find the best composition of the three sources able to cover a desired share of energy demand. The approach is applied to Ca Mau, a province in the southern part of Vietnam. Finally, the results encourage the adoption of these energy sources that could be easily implemented up to a share of the local energy demand equal to 65%.

Abstract One of the critical areas in the outer shell of household refrigerators is the compressor compartment, which has relatively high temperatures, due to the heat generated while the compressor is running. This implies a larger heat transfer to the interior air volume and, consequently, more energy consumption. One way to decrease this temperature is to ventilate the base of the refrigerator with a small fan. In the research carried out, a decrease of 11 °C in the temperature of the surfaces close to the compressor was recorded, when the fan was running. The implications of this effect can be seen at two levels: changes in the temperature distribution at the bottom of the refrigerator envelope and the resulting dynamic effects, and a decrease in energy consumption of the entire system. Consequently, there are lower CO 2 emissions to the environment, making household refrigerators more efficient and sustainable.

Abstract For the option of “carbon capture and storage”, an integrated assessment in the form of a life cycle analysis and a cost assessment combined with a systematic comparison with renewable energies regarding future conditions in the power plant market for the situation in Germany is done. The calculations along the whole process chain show that CCS technologies emit per kWh more than generally assumed in clean-coal concepts (total CO2 reduction by 72–90% and total greenhouse gas reduction by 65–79%) and considerable more if compared with renewable electricity. Nevertheless, CCS could lead to a significant absolute reduction of GHG-emissions within the electricity supply system. Furthermore, depending on the growth rates and the market development, renewables could develop faster and could be in the long term cheaper than CCS based plants. Especially, in Germany, CCS as a climate protection option is phasing a specific problem as a huge amount of fossil power plant has to be substituted in the next 15 years where CCS technologies might be not yet available. For a considerable contribution of CCS to climate protection, the energy structure in Germany requires the integration of capture ready plants into the current renewal programs. If CCS retrofit technologies could be applied at least from 2020, this would strongly decrease the expected CO2 emissions and would give a chance to reach the climate protection goal of minus 80% including the renewed fossil-fired power plants.

Plant-soil feedback (PSF) describes the process whereby plant species modify the soil environment, which subsequently impacts the growth of the same or another plant species. Our aim was to explore PSF by two maize varieties (a landrace and a hybrid variety) and three arbuscular mycorrhizal fungi (AMF) species (Funneliformis mosseae, Claroideoglomus etunicatum, Gigaspora margarita, and the mixture). We carried out a pot experiment with a conditioning and a feedback phase to determine PSF with different species of AMF and with a non-mycorrhizal control. Sterilized soil was conditioned separately by each variety, with or without AMF; in the feedback phase, each soil community was used to grow each in its "home" soil and in the "away" soil. Plant performance was assessed as shoot biomass, phosphorus (P) concentration and P content, and fungal performance was assessed as mycorrhizal colonization and hyphal length density. Both maize varieties were differentially influenced by AMF in the conditioning phase. In the feedback phase, PSF was generally negative for non-mycorrhizal plants or when plants were colonized by G. margarita, whereas PSF was positive in the other three AMF treatments. When plants were grown on home soil, hyphal length density was larger than on away soil. We conclude that different maize varieties can strengthen positive plant-soil feedback for themselves through beneficial mutualists for themselves, but not across the maize varieties.