• Energy Research
• Open Access close
• Closed Access close
• Restricted close
• ZENODO close

The presented Report forms Deliverable D6.2 resulted from the realization of Workpackage WP.6.3 titled “Overview of market drivers, fiscal measures and subsidies” in frame of the EU-Project “Geothermal communities – demonstrating the cascaded use of geothermal energy for district heating with small scale RES integration and retrofitting measures” (GEOCOM). The following seven countries were covered by WP6.3 works and this Deliverable D6.2: o Macedonia, o Hungary, o Italy, o Poland, o Romania, o Serbia, o Slovakia. The work was done with the contribution of all GEOCOM Project Partner teams and appointed experts, coordinated, interpreted and summarized by the Mineral and Energy Economy Research Institute of PAS team, WP6 leader. FP7

Abstract. Since the first estimate of global CO2 emissions was published in 1894, important progress has been made in the development of estimation methods while the number of available datasets has grown. The existence of parallel efforts should lead to improved accuracy and understanding of emissions estimates, but there remains significant deviation between estimates and relatively poor understanding of the reasons for this. Here I describe the most important global emissions datasets available today and – by way of global, large-emitter, and case examples – quantitatively compare their estimates, exploring the reasons for differences. In many cases differences in emissions come down to differences in system boundaries: which emissions sources are included and which are omitted. With minimal work in harmonising these system boundaries across datasets, the range of estimates of global emissions drops to 5 %, and further work on harmonisation would likely result in an even lower range, without changing the data. Some potential errors were found, and some discrepancies remain unexplained, but it is shown to be inappropriate to conclude that uncertainty in emissions is high simply because estimates exhibit a wide range. While true emissions cannot be known, by comparing different datasets methodically, differences that result from system boundaries and allocation approaches can be highlighted and set aside to enable identification of true differences, and potential errors. This must be an important way forward in improving global datasets of CO2 emissions. Data used to generate figures 4–19 are available at https://doi.org/10.5281/zenodo.3687042 (Andrew, 2020).

Sustainable food supply has gained considerable consumer concern due to the high percentage of spoilage microorganisms. Food industries need to expand advanced technologies that can maintain the nutritive content of foods, enhance the bio-availability of bioactive compounds, provide environmental and economic sustainability, and fulfill consumers’ requirements of sensory characteristics. Heat treatment negatively affects food samples’ nutritional and sensory properties as bioactives are sensitive to high-temperature processing. The need arises for non-thermal processes to reduce food losses, and sustainable developments in preservation, nutritional security, and food safety are crucial parameters for the upcoming era. Non-thermal processes have been successfully approved because they increase food quality, reduce water utilization, decrease emissions, improve energy efficiency, assure clean labeling, and utilize by-products from waste food. These processes include pulsed electric field (PEF), sonication, high-pressure processing (HPP), cold plasma, and pulsed light. This review describes the use of HPP in various processes for sustainable food processing. The influence of this technique on microbial, physicochemical, and nutritional properties of foods for sustainable food supply is discussed. This approach also emphasizes the limitations of this emerging technique. HPP has been successfully analyzed to meet the global requirements. A limited global food source must have a balanced approach to the raw content, water, energy, and nutrient content. HPP showed positive results in reducing microbial spoilage and, at the same time, retains the nutritional value. HPP technology meets the essential requirements for sustainable and clean labeled food production. It requires limited resources to produce nutritionally suitable foods for consumers’ health.

The electric power system has undergone numerous changes over the years. The transformation of the end-users from passive actors to active actors brings implications for the electric power system. The distribution system operator will be able to guide its operations in the function of the active role of the end-users. In many situations, the distribution system operator is carried out to avoid congestion in the distribution networks, and when it happens the distribution system operator is obliged to compensate the affected end-users. This paper presents a model in which distribution system operator can take advantage of the flexibility of the end-users in order to minimize the costs of the investments in distribution network expansion. The investment cost with the presented methodology as show the results has a reduction of 5.77%.

AbstractCurrently, Sb2Se3 thin films receive considerable research interest as a solar cell absorber material. When completed into a device stack, the major bottleneck for further device improvement is the open‐circuit voltage, which is the focus of the work presented here. Polycrystalline thin‐film Sb2Se3 absorbers and solar cells are prepared in substrate configuration and the dominant recombination path is studied using photoluminescence spectroscopy and temperature‐dependent current–voltage characteristics. It is found that a post‐deposition annealing after the CdS buffer layer deposition can effectively remove interface recombination since the activation energy of the dominant recombination path becomes equal to the bandgap of the Sb2Se3 absorber. The increased activation energy is accompanied by an increased photoluminescence yield, that is, reduced non‐radiative recombination. Finished Sb2Se3 solar cell devices reach open‐circuit voltages as high as 485 mV. Contrarily, the short‐circuit current density of these devices is limiting the efficiency after the post‐deposition annealing. It is shown that atomic layer‐deposited intermediate buffer layers such as TiO2 or Sb2S3 can pave the way for overcoming this limitation.

As population grows, demand for reliable and sustainable energy increases prompting the need for innovative solutions. The numerous strategies are needed to shift centralized power generation to distributed generation in the evolution of smart energy systems. The response and electricity market paradigms using multiple loads are missing in literature. In this paper, multiple loads are considered to propose optimal energy hub modeling comprised of the various sources and storage. The proposed system is modelled using demand response technique. The exact method-based optimization is used to simulate the proposed model in MATLAB. The results obtained show the effectiveness of the proposed model to reduce the operational cost and greenhouse gas (GHG) emissions. A case study is taken, where a poultry farm producing approximately 1.94 million tons of poultry waste annually, is used to evaluate the proposed model. For the industrial load, the optimized scheduling reduced the operational cost to $161.8 as compared to $1670 relying only on the utility grid. For the residential load, the optimized cost is reduced by -$3.3 from the pre-optimization cost of $2.7. This work highlights the economic and environmental benefits, particularly in developing countries where biomass-based energy generation is yet to be fully explored.

<p>Commonly used host rock reservoirs for Enhanced Geothermal Systems (EGS) are composed of granite, as they display highly conductive and sustainable fracture networks after stimulation. However, considering the large amount of metamorphic rocks in Europe’s underground, these rock types may also show a large potential to extract geothermal energy from the subsurface. Within the framework of the European Union’s Horizon 2020 initiative ‘MEET (Multi-Sites EGS Demonstration)’, we are conducting fracture permeability experiments at elevated confining pressures, p<sub>c</sub>, temperatures, T, and differential stresses, </p>