• Energy Research
• Restricted close
• Embargo close
• 7. Clean energy close
• 11. Sustainability close
• 12. Responsible consumption close
• 2. Zero hunger close

Renewable energy has been prioritized in Danish energy policy since the early 1980s. This has led to the current situation where Denmark is one of the leading countries in the world in the field of wind energy utilization. The background for this success is a story about how a society can manage the development and diffusion of sustainable technologies so that they are simultaneously socially acceptable and environmentally benign. Consequently, this article describes the relationship between the organization of wind power and the protection of nature. The aim is to analyse which kinds of public planning and policy can promote wind power and nature protection in a situation where a conflict exists between these two issues. The discussion acknowledges that it has been a serious problem to balance these contrasting considerations. However, it also suggests that the problems seem solvable if technology development, the social organization relating to the use of the technology and proper planning are brought together to work in a spirit of local involvement. © 1998 John Wiley & Sons, Ltd. and ERP Environment

In this paper some preliminary experimental results on a Zebra battery based propulsion system for urban bus applications are presented. The tests were carried out using a laboratory 1:1 scale test bench, composed by a 65 kW electric drive, specifically designed for urban bus applications, supplied by two 20 kWh Zebra batteries connected in parallel. The electric power train was tested on a laboratory bench, connected through a fixed ratio gear box to a 100 kW regenerative electric brake provided with speed and torque controls, in order to evaluate the propulsion system performance in steady state operative conditions. The obtained preliminary experimental results were utilized to implement a Matlab-Simulink model of urban bus, which might be powered by the same electric propulsion system studied. Thanks to this model it was possible to evaluate the dynamic behavior of the urban bus, working on standard driving cycles, taking into account the resistant forces represented by proper vehicle/road/aerodynamic parameters. An evaluation of the expected real vehicle driving range was also estimated in different road conditions.

Solar Energy Materials and Solar Cells, 116 + (2013) 176-181. doi:10.1016/j.solmat.2013.04.019

Green tea catechins mixed with caffeine have been proposed as adjuvants for maintaining or enhancing energy expenditure and for increasing fat oxidation, in the context of prevention and treatment of obesity. These catechins-caffeine mixtures seem to counteract the decrease in metabolic rate that occurs during weight loss. Their effects are of particular importance during weight maintenance after weight loss. Other metabolic targets may be fat absorption and the gut microbiota composition, but these effects still need further investigation in combination with weight loss. Limitations for the effects of green tea catechins are moderating factors such as genetic predisposition related to COMT-activity, habitual caffeine intake, and ingestion combined with dietary protein. In conclusion, a mixture of green tea catechins and caffeine has a beneficial effect on body-weight management, especially by sustained energy expenditure, fat oxidation, and preservation of fat free body-mass, after energy restriction induced body-weight loss, when taking the limitations into account.

A methodology for the sizing of domestic hot water heating and storage systems is defined, by assuming an extreme operating condition cycle composed of only two parts, a water consumption period and a system repositioning period. In both parts to respond to the extreme hot water demanding conditions, the heating is always on. The subsequent exergy analysis of this domestic hot water production system compares the irreversibility and the exergy efficiency of the water storage and the tankless situation. To carry out such analysis, some basic assumptions were made: a constant temperature heat source, a short duration operating cycle and a constant thermal energy supply. Under these circumstances it is shown that the hot water storage system leads to lower exergy losses while the tankless system is more exergy efficient, but requiring a higher instantaneous thermal power input. The use of the joule effect electricity, as the system heat source, be it a water storage one or a tankless one, maximizes the system irreversibility losses and minimizes the system exergy efficiency. The tankless system, with the joule effect electricity heat source is the worst situation.

This paper aims to correlate the in-cylinder soot formation and the exhaust particle emissions for different methods of gasoline/ethanol fueling in spark ignition engine. In particular, the engine was fueled with gasoline and ethanol separately and not, in this latter case both blended (E30) and dual fueled (EDF). For E30 the bend was direct injected and for EDF, the ethanol was injected in the combustion chamber and the gasoline into the intake duct. For both the injection configurations, the same percentage of ethanol in gasoline was supplied: 30%v/v. The measurements were carried out at 2000 and 4000 rpm, under full load, and stoichiometric condition, in small single cylinder optical engine. 2D-digital imaging was performed to follow the combustion process with a high spatial and temporal resolution through a full-bore optical piston. The two-color pyrometry was applied for the analysis of the in cylinder soot formation in the combustion chamber. Particle mass concentration was evaluated at the exhaust by means of a smoke meter. The particle size distribution function was measured in the range from 5.6 to 560 nm by an Engine Exhaust Particle Sizer (EEPS). It was observed that the use of ethanol allows the reduction of soot formation and particles emission in DI configuration. However, for E30 the in-cylinder soot formation and emissions are larger than EDF. This result is mainly due to the different contribution of gasoline. Optical analysis shows that in E30 the direct injected gasoline causes wide diffusive flames where soot formation is promoted; whereas for EDF the better evaporation and mixing of gasoline, typical of PFI configuration, results in few, small, and localized diffusive flames producing smaller particle emissions.

The use of methane as supplement to liquid fuel is one of the solution proposed for the reduction of the internal combustion engine pollutant emissions. Its intrinsic properties as the high knocking resistance and the low carbon content makes methane the most promising clean fuel. The dual fuel combustion mode allows improving the methane combustion acting mainly on the methane slow burning velocity and allowing lean burn combustion mode. An experimental investigation was carried out to study the methane-gasoline dual fuel combustion. Methane was injected in combustion chamber (DI fuel) while gasoline was injected in the intake manifold (PFI fuel). The measurements were carried out in an optically accessible small single-cylinder four-stroke engine. It was equipped with the cylinder head of a commercial 250 cc motorcycles engine representative of the most popular two-wheel vehicles in Europe. UV-visible spectroscopy measurements were performed to analyze the combustion process with high spatial and temporal resolution. In particular, UV-visible spectroscopy allows detecting the chemical markers of combustion process such as the radicals OH* and CH*. The in-cylinder lambda spatial and temporal evolution was evaluated. The combustion evolution is characterized by means of a high speed cycle resolved camera. The exhaust emissions were characterized by means of gaseous analyzers. The measurements were performed under steady state conditions at different engine operating conditions.

A new concept of a system for Combined Heat and Power generation is presented. The concept is based on hybrid use of two renewable energy sources, direct solar (thermodynamic solar) and biomass (indirect solar energy). Biomass combustion is conducted using a fluidized bed combustor. A second source of energy, given by the direct irradiation of the bed with a concentrated solar radiation, is integrated in the same system, using the fluidized bed as solar receiver. A Stirling engine converts heat into mechanical power. A Scheffler type mirror is adopted to allow irradiation of the system in a fixed focal point. Advantages of the proposed solution are illustrated and some preliminary results on the performance of the system, obtained with a simple model, are presented. The principal improvements with respect to existing systems of similar size and primary energy source are illustrated. The most important are the enhanced heat transfer processes that are realized with the help of the fluidized bed, and the possibility of continuous cogeneration during the day. Different working conditions are considered to estimate the contribution given by the burning of fuel, in presence as well as in absence of sun irradiation (as during the night). The distribution of energy shares among the different flux contributes is reported versus the amount of biomass burned per unit time. The results clearly demonstrate the advantage of coupling, in the same system, two sources for heat generation, thus maintaining the option of producing electricity without the supply of biomass fuel.